drm/i915: Move DPIO phy documentation section to intel_dpio_phy.c

Move the DPIO phy documentation section to intel_dpio_phy.c, since that
is a more suitable place now that there is a source file dedicated for
those phys.

Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/55a2d38c15c06a8c5bce498b28decc03948f0224.1475770848.git-series.ander.conselvan.de.oliveira@intel.com

Documentation/gpu/i915.rst

@@ -189,7 +189,7 @@ Display Refresh Rate Switching (DRRS)
 DPIO
 ----
 
-.. kernel-doc:: drivers/gpu/drm/i915/i915_reg.h
+.. kernel-doc:: drivers/gpu/drm/i915/intel_dpio_phy.c
    :doc: DPIO
 
 CSR firmware support for DMC

drivers/gpu/drm/i915/i915_reg.h

@@ -830,96 +830,7 @@ enum skl_disp_power_wells {
 #define  CCK_FREQUENCY_STATUS_SHIFT		8
 #define  CCK_FREQUENCY_VALUES			(0x1f << 0)
 
-/**
+/* DPIO registers */
- * DOC: DPIO
- *
- * VLV, CHV and BXT have slightly peculiar display PHYs for driving DP/HDMI
- * ports. DPIO is the name given to such a display PHY. These PHYs
- * don't follow the standard programming model using direct MMIO
- * registers, and instead their registers must be accessed trough IOSF
- * sideband. VLV has one such PHY for driving ports B and C, and CHV
- * adds another PHY for driving port D. Each PHY responds to specific
- * IOSF-SB port.
- *
- * Each display PHY is made up of one or two channels. Each channel
- * houses a common lane part which contains the PLL and other common
- * logic. CH0 common lane also contains the IOSF-SB logic for the
- * Common Register Interface (CRI) ie. the DPIO registers. CRI clock
- * must be running when any DPIO registers are accessed.
- *
- * In addition to having their own registers, the PHYs are also
- * controlled through some dedicated signals from the display
- * controller. These include PLL reference clock enable, PLL enable,
- * and CRI clock selection, for example.
- *
- * Eeach channel also has two splines (also called data lanes), and
- * each spline is made up of one Physical Access Coding Sub-Layer
- * (PCS) block and two TX lanes. So each channel has two PCS blocks
- * and four TX lanes. The TX lanes are used as DP lanes or TMDS
- * data/clock pairs depending on the output type.
- *
- * Additionally the PHY also contains an AUX lane with AUX blocks
- * for each channel. This is used for DP AUX communication, but
- * this fact isn't really relevant for the driver since AUX is
- * controlled from the display controller side. No DPIO registers
- * need to be accessed during AUX communication,
- *
- * Generally on VLV/CHV the common lane corresponds to the pipe and
- * the spline (PCS/TX) corresponds to the port.
- *
- * For dual channel PHY (VLV/CHV):
- *
- *  pipe A == CMN/PLL/REF CH0
- *
- *  pipe B == CMN/PLL/REF CH1
- *
- *  port B == PCS/TX CH0
- *
- *  port C == PCS/TX CH1
- *
- * This is especially important when we cross the streams
- * ie. drive port B with pipe B, or port C with pipe A.
- *
- * For single channel PHY (CHV):
- *
- *  pipe C == CMN/PLL/REF CH0
- *
- *  port D == PCS/TX CH0
- *
- * On BXT the entire PHY channel corresponds to the port. That means
- * the PLL is also now associated with the port rather than the pipe,
- * and so the clock needs to be routed to the appropriate transcoder.
- * Port A PLL is directly connected to transcoder EDP and port B/C
- * PLLs can be routed to any transcoder A/B/C.
- *
- * Note: DDI0 is digital port B, DD1 is digital port C, and DDI2 is
- * digital port D (CHV) or port A (BXT). ::
- *
- *
- *     Dual channel PHY (VLV/CHV/BXT)
- *     ---------------------------------
- *     |      CH0      |      CH1      |
- *     |  CMN/PLL/REF  |  CMN/PLL/REF  |
- *     |---------------|---------------| Display PHY
- *     | PCS01 | PCS23 | PCS01 | PCS23 |
- *     |-------|-------|-------|-------|
- *     |TX0|TX1|TX2|TX3|TX0|TX1|TX2|TX3|
- *     ---------------------------------
- *     |     DDI0      |     DDI1      | DP/HDMI ports
- *     ---------------------------------
- *
- *     Single channel PHY (CHV/BXT)
- *     -----------------
- *     |      CH0      |
- *     |  CMN/PLL/REF  |
- *     |---------------| Display PHY
- *     | PCS01 | PCS23 |
- *     |-------|-------|
- *     |TX0|TX1|TX2|TX3|
- *     -----------------
- *     |     DDI2      | DP/HDMI port
- *     -----------------
- */
 #define DPIO_DEVFN			0
 
 #define DPIO_CTL			_MMIO(VLV_DISPLAY_BASE + 0x2110)

drivers/gpu/drm/i915/intel_dpio_phy.c

@@ -23,6 +23,97 @@
 
 #include "intel_drv.h"
 
+/**
+ * DOC: DPIO
+ *
+ * VLV, CHV and BXT have slightly peculiar display PHYs for driving DP/HDMI
+ * ports. DPIO is the name given to such a display PHY. These PHYs
+ * don't follow the standard programming model using direct MMIO
+ * registers, and instead their registers must be accessed trough IOSF
+ * sideband. VLV has one such PHY for driving ports B and C, and CHV
+ * adds another PHY for driving port D. Each PHY responds to specific
+ * IOSF-SB port.
+ *
+ * Each display PHY is made up of one or two channels. Each channel
+ * houses a common lane part which contains the PLL and other common
+ * logic. CH0 common lane also contains the IOSF-SB logic for the
+ * Common Register Interface (CRI) ie. the DPIO registers. CRI clock
+ * must be running when any DPIO registers are accessed.
+ *
+ * In addition to having their own registers, the PHYs are also
+ * controlled through some dedicated signals from the display
+ * controller. These include PLL reference clock enable, PLL enable,
+ * and CRI clock selection, for example.
+ *
+ * Eeach channel also has two splines (also called data lanes), and
+ * each spline is made up of one Physical Access Coding Sub-Layer
+ * (PCS) block and two TX lanes. So each channel has two PCS blocks
+ * and four TX lanes. The TX lanes are used as DP lanes or TMDS
+ * data/clock pairs depending on the output type.
+ *
+ * Additionally the PHY also contains an AUX lane with AUX blocks
+ * for each channel. This is used for DP AUX communication, but
+ * this fact isn't really relevant for the driver since AUX is
+ * controlled from the display controller side. No DPIO registers
+ * need to be accessed during AUX communication,
+ *
+ * Generally on VLV/CHV the common lane corresponds to the pipe and
+ * the spline (PCS/TX) corresponds to the port.
+ *
+ * For dual channel PHY (VLV/CHV):
+ *
+ *  pipe A == CMN/PLL/REF CH0
+ *
+ *  pipe B == CMN/PLL/REF CH1
+ *
+ *  port B == PCS/TX CH0
+ *
+ *  port C == PCS/TX CH1
+ *
+ * This is especially important when we cross the streams
+ * ie. drive port B with pipe B, or port C with pipe A.
+ *
+ * For single channel PHY (CHV):
+ *
+ *  pipe C == CMN/PLL/REF CH0
+ *
+ *  port D == PCS/TX CH0
+ *
+ * On BXT the entire PHY channel corresponds to the port. That means
+ * the PLL is also now associated with the port rather than the pipe,
+ * and so the clock needs to be routed to the appropriate transcoder.
+ * Port A PLL is directly connected to transcoder EDP and port B/C
+ * PLLs can be routed to any transcoder A/B/C.
+ *
+ * Note: DDI0 is digital port B, DD1 is digital port C, and DDI2 is
+ * digital port D (CHV) or port A (BXT). ::
+ *
+ *
+ *     Dual channel PHY (VLV/CHV/BXT)
+ *     ---------------------------------
+ *     |      CH0      |      CH1      |
+ *     |  CMN/PLL/REF  |  CMN/PLL/REF  |
+ *     |---------------|---------------| Display PHY
+ *     | PCS01 | PCS23 | PCS01 | PCS23 |
+ *     |-------|-------|-------|-------|
+ *     |TX0|TX1|TX2|TX3|TX0|TX1|TX2|TX3|
+ *     ---------------------------------
+ *     |     DDI0      |     DDI1      | DP/HDMI ports
+ *     ---------------------------------
+ *
+ *     Single channel PHY (CHV/BXT)
+ *     -----------------
+ *     |      CH0      |
+ *     |  CMN/PLL/REF  |
+ *     |---------------| Display PHY
+ *     | PCS01 | PCS23 |
+ *     |-------|-------|
+ *     |TX0|TX1|TX2|TX3|
+ *     -----------------
+ *     |     DDI2      | DP/HDMI port
+ *     -----------------
+ */
+
 bool bxt_ddi_phy_is_enabled(struct drm_i915_private *dev_priv,
 			    enum dpio_phy phy)
 {