This is a methodical transition of the driver from phylib
to phylink, following the guidelines from sfp-phylink.rst.
The MAC register configurations based on interface mode
were moved from the probing path to the mac_config() hook.
MAC enable and disable commands (enabling Rx and Tx paths
at MAC level) were also extracted and assigned to their
corresponding phylink hooks.
As part of the migration to phylink, the serdes configuration
from the driver was offloaded to the PCS_LYNX module,
introduced in commit 0da4c3d393 ("net: phy: add Lynx PCS module"),
the PCS_LYNX module being a mandatory component required to
make the enetc driver work with phylink.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.cionei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use DT information rather than in-band information from bootloader to
set up MAC for XGMII. For RGMII use the DT indication in addition to
RGMII defaults in hardware.
However, this implies that PHY connection information needs to be
extracted before netdevice creation, when the ENETC Port MAC is
being configured.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ENETC has ethernet MACs capable of SGMII, 2500BaseX and USXGMII. But in
order to use these protocols some SerDes configurations need to be
performed. The SerDes is configurable via an internal PCS PHY which is
connected to an internal MDIO bus at address 0.
This patch basically removes the dependency on bootloader regarding
SerDes initialization.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Within the LS1028A SoC, the register map for the ENETC MDIO controller
is instantiated a few times: for the central (external) MDIO controller,
for the internal bus of each standalone ENETC port, and for the internal
bus of the Felix switch.
Refactoring is needed to support multiple MDIO buses from multiple
drivers. The enetc_hw structure is made an opaque type and a smaller
enetc_mdio_priv is created.
'mdio_base' - MDIO registers base address - is being parameterized, to
be able to work with different MDIO register bases.
The ENETC MDIO bus operations are exported from the fsl-enetc-mdio
kernel object, the same that registers the central MDIO controller (the
dedicated PF). The ENETC main driver has been changed to select it, and
use its exported helpers to further register its private MDIO bus. The
DSA Felix driver will do the same.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each ENETC PF has its own MDIO interface, the corresponding
MDIO registers are mapped in the ENETC's Port register block.
The current patch adds a driver for these PF level MDIO buses,
so that each PF can manage directly its own external link.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
VSIs (VFs) may send a message to the PSI (PF) for general notification
or to gain access to hardware resources which requires host inspection.
These messages may vary in size and are handled as a partition copy
between two memory regions owned by the respective participants.
The PSI will respond with fail or success and a 16-bit message code.
The patch implements the vf to pf messaging mechanism above and, as the
first application making use of this support, it enables the VF to
configure its own primary MAC address.
Signed-off-by: Catalin Horghidan <catalin.horghidan@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ENETC is a multi-port virtualized Ethernet controller supporting GbE
designs and Time-Sensitive Networking (TSN) functionality.
ENETC is operating as an SR-IOV multi-PF capable Root Complex Integrated
Endpoint (RCIE). As such, it contains multiple physical (PF) and
virtual (VF) PCIe functions, discoverable by standard PCI Express.
Introduce basic PF and VF ENETC ethernet drivers. The PF has access to
the ENETC Port registers and resources and makes the required privileged
configurations for the underlying VF devices. Common functionality is
controlled through so called System Interface (SI) register blocks, PFs
and VFs own a SI each. Though SI register blocks are almost identical,
there are a few privileged SI level controls that are accessible only to
PFs, and so the distinction is made between PF SIs (PSI) and VF SIs (VSI).
As such, the bulk of the code, including datapath processing, basic h/w
offload support and generic pci related configuration, is shared between
the 2 drivers and is factored out in common source files (i.e. enetc.c).
Major functionalities included (for both drivers):
MSI-X support for Rx and Tx processing, assignment of Rx/Tx BD ring pairs
to MSI-X entries, multi-queue support, Rx S/G (Rx frame fragmentation) and
jumbo frame (up to 9600B) support, Rx paged allocation and reuse, Tx S/G
support (NETIF_F_SG), Rx and Tx checksum offload, PF MAC filtering and
initial control ring support, VLAN extraction/ insertion, PF Rx VLAN
CTAG filtering, VF mac address config support, VF VLAN isolation support,
etc.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
