DDI ports have its encoders initialized with INTEL_OUTPUT_DDI type and
later eDP ports that have the type changed to INTEL_OUTPUT_EDP.
But for all other DDI ports it can drive HDMI or DP depending on what
user connects to the ports.
ehl_get_combo_buf_trans() and tgl_get_combo_buf_trans() was checking
for INTEL_OUTPUT_DP that was never true, causing wrong vswing tables
being used.
So here replacing the INTEL_OUTPUT_DP checks by the valid output types
that this functions receives as parameters. HDMI cases will be
correctly handled as it do not use encoder->type, instead it calls the
functions with INTEL_OUTPUT_HDMI as type parameter and HDMI don't have
retraining.
v2:
changed INTEL_OUTPUT_DDI to INTEL_OUTPUT_EDP and INTEL_OUTPUT_HDMI
Fixes: bd3cf6f7ce ("drm/i915/dp/tgl+: Update combo phy vswing tables")
Cc: Clinton A Taylor <clinton.a.taylor@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200330210044.130510-1-jose.souza@intel.com
(cherry picked from commit 70988115ac)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The DDI IO power well must not be enabled for a TypeC port in TBT mode,
ensure this during driver loading/system resume.
This gets rid of error messages like
[drm] *ERROR* power well DDI E TC2 IO state mismatch (refcount 1/enabled 0)
and avoids leaking the power ref when disabling the output.
Cc: <stable@vger.kernel.org> # v5.4+
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200330152244.11316-1-imre.deak@intel.com
(cherry picked from commit f77a2db27f)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Converting error to debug print if sink fails to configure scrambling or
TMDS bit clock ratio. In this case, we are timing out while disabling
the scrambling and setting the SCDC ratio, as there is no response
to the I2C SCDC write from the sink device. Error isn't due to something
wrong done from driver side.
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200302213807.6488-1-swati2.sharma@intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
intel_ddi_clock_get() tests the DPLL ID against DPLL_ID_ICL_TBTPLL (2)
to determine whether to try to descend into a TBT-specific handler.
However this test will also be true when DPLL4 on EHL is used since that
shares the same DPLL ID (2).
Add an extra check to ensure the PHY is actually a Type-C PHY before
descending into the TBT handling. This should ensure EHL still takes
the correct code path and somewhat future-proof the code as well.
v2: Drop the gen+ check since only gen11+ platforms can have Type-C
outputs. (Imre)
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/issues/1369
Fixes: 45e4728b87 ("drm/i915: Move DPLL frequency calculation to intel_dpll_mgr.c")
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303195043.959913-1-matthew.d.roper@intel.com
Move all the DPLL params->DPLL frequency conversion functions to
intel_dpll_mgr.c where the corresponding inverse conversions are.
The GEN11+ TBT PLL outputs multiple frequencies and for selecting the
one in use we need to check the DDI CLK mux. As part of the DDI clock
logic this selection is kept in intel_ddi.c.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226203455.23032-7-imre.deak@intel.com
For clarity add a new DPLL specific struct to the i915 device struct and
move all DPLL fields into it. Accordingly remove the dpll_ prefixes, as
the new struct already provides the required namespacing.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226203455.23032-4-imre.deak@intel.com
This patch pushes out the computation of master and slave
transcoders in crtc states after encoder's compute_config hook.
This ensures that the assigned master slave crtcs have exact same
mode and timings which is a requirement for Port sync mode
to be enabled.
v3:
* Make crtc_state const, remove crtc state NULL init (Ville)
v2:
* Correct indentation
* Rename to intel_ddi_port_sync_transcoders (Ville)
* remove unwanted debug (Ville)
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200214114126.13192-2-manasi.d.navare@intel.com
Commit 1c9d2eb241 ("drm/i915: move intel_dp_set_m_n() to encoder for
DDI platforms") moved the intel_dp_set_m_n() from hsw_crtc_enable()
to intel_ddi_pre_enable_dp() but it missed add it to
intel_mst_pre_enable_dp() causing MST slaves to not work.
v2: Not setting intel_ddi_set_dp_msa() twice for MST master
Fixes: 1c9d2eb241 ("drm/i915: move intel_dp_set_m_n() to encoder for DDI platforms")
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200211185008.30806-1-jose.souza@intel.com
A recent bspec update added an extra voltage level that we didn't have
on ICL and new criteria for selecting the level.
Bspec: 49208
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200207001417.1229251-2-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Voltage level depends not only on the cdclk, but also on the DDI clock.
Last time the bspec voltage level table for EHL was updated, we only
updated the cdclk requirements, but forgot to account for the new port
clock criteria.
Bspec: 21809
Fixes: d147483884 ("drm/i915/ehl: Update voltage level checks")
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200207001417.1229251-1-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
TGL is suffering of timeouts and fifo underruns when disabling
transcoder in MST mode, this is fixed by set TRANS_DDI_MODE_SELECT to
0(HDMI mode) when clearing DDI select.
Although BSpec disable sequence don't require this step, it is a
harmless change and it is also done by Windows driver.
Anyhow HW team was notified about that but it can take some time to
documentation to be updated.
A case that always lead to those issues is:
- do a modeset enabling pipe A and pipe B in the same MST stream
leaving A as master
- disable pipe A, promote B as master doing a full modeset in A
- enable pipe A, changing the master transcoder back to A(doing a
full modeset in B)
- Pow: underruns and timeouts
The transcoders involved will only work again when complete disabled
and their power wells turned off causing a reset in their registers.
v2: Setting TRANS_DDI_MODE_SELECT to default when clearing DDI select
not anymore when disabling TRANS_DDI, both work but this one looks
more safe. (Ville comment)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200203225549.152301-1-jose.souza@intel.com
The DDI encoder code shouln't have to know about the guts of
HDCP. Abstract the pipe update code to a new intel_hdcp_update_pipe() in
intel_hdcp.c. No functional changes.
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200128163803.5954-1-jani.nikula@intel.com
To allow better flexibility for encoder specific code, push
intel_enable_pipe(), lpt_pch_enable() and intel_crtc_vblank_on() down to
the encoders from hsw_crtc_enable().
There's slight duplication, but also more clarity with the reduced
conditional statements.
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200128162850.8660-1-jani.nikula@intel.com
A recent change in BSpec allow us to change EXTLINE while transcoder
is enabled so this allow us to change it even when doing the first
fastset after taking over previous hardware state set by BIOS.
BIOS don't enable PSR, so if sink supports PSR it will be enabled on
the first fastset, so moving the EXTLINE compute and set to PSR flows
allow us to simplfy a bunch of code.
This will save a lot of time in all the IGT tests that uses CRC, as
when PSR2 is enabled CRCs are not generated, so we switch to PSR1, so
the previous code would compute dc3co_exitline=0 causing a full
modeset that would shutdown pipe, enable and train link.
v2: only programming EXTLINE when DC3CO is enabled
BSpec: 49196
Cc: Imre Deak <imre.deak@intel.com>
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200122182617.18597-2-jose.souza@intel.com
TGL has now a table for RBR and HBR and another table for HBR2 over
combo phys. The HBR2 one has some small changes comparing to the ICL
one, so adding two new tables and adding a function to return TGL
combo phy tables.
v2:
- reordered the tgl_combo_phy_ddi_translations_dp_hbr2 to reduce diff
(Matt)
- removed definition of rates, kept using raw number(Jani and Ville)
- changed code to use icl_get_combo_buf_trans() for non-DP as those
are equal between TGL and ICL(Matt)
BSpec: 49291
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200110233902.154960-1-jose.souza@intel.com
When moving the pipe disable & co. function calls from
haswell_crtc_disable() into the encoder .post_disable() hooks I
neglected to account for the MST vs. DDI interactions properly.
This now leads us to call these functions two times for the last
MST stream (once from the MST code and a second time from the DDI
code). The calls from the DDI code should only be done for SST
and not MST. Add the proper check for that.
This results in an MCE on ICL. My vague theory is that we turn off
the transcoder clock from the MST code and then we proceed to touch
something in the DDI code which still depends on that clock causing
the hardware to become upset. Though I can't really explain why
Stan's hack of omitting the pipe disable in the MST code would avoid
the MCE since we should still be turning off the transcoder clock.
But maybe there's something magic in the hw that keeps the clock on
as long as the pipe is on. Or maybe the clock isn't the problem and
we now touch something in the DDI disable code that really does need
the pipe to be still enabled.
v2: Rebase to latest drm-tip
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Reported-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/issues/901
Fixes: 773b4b5435 ("drm/i915: Move stuff from haswell_crtc_disable() into encoder .post_disable()")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200108144550.29280-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Talked with HW team and this is a left over, driver should not
program clockgating, mg or dekel firmware is reponsible for any
clockgating programing.
Also removing the register and bits definition related to clockgating.
v2:
Added WARN_ON
v3:
Only calling icl_phy_set_clock_gating() on intel_ddi_pre_enable_hdmi
for GEN11
v4:
ICL should also not program clockgating (thanks Matt for catching
this)
BSpec issue: 20885
BSpec: 49292
BSpec: 21735
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200107170922.153612-1-jose.souza@intel.com
While clearing the Ports ync mode enable and master select bits
we need to clear the register completely instead of using disable masks
v3:
* Remove reg variable (Matt)
v2:
* Just write 0 to the reg (Ville)
* Rebase
Bugzilla: https://gitlab.freedesktop.org/drm/intel/issues/5
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Fixes: 51528afe7c ("drm/i915/display/icl: Disable transcoder port sync as part of crtc_disable() sequence")
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191228031204.10189-3-manasi.d.navare@intel.com
We are currently using a mix of platform name and acronym to name the
functions. Let's prefer the acronym as it should be clear what platform
it's about and it's shorter, so it doesn't go over 80 columns in a few
cases. This converts ironlake to ilk where appropriate.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191224084012.24241-7-lucas.demarchi@intel.com
We are currently using a mix of platform name and acronym to name the
functions. Let's prefer the acronym as it should be clear what platform
it's about and it's shorter, so it doesn't go over 80 columns in a few
cases. This converts skylake to skl where appropriate.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191224084012.24241-4-lucas.demarchi@intel.com
We are currently using a mix of platform name and acronym to name the
functions. Let's prefer the acronym as it should be clear what platform
it's about and it's shorter, so it doesn't go over 80 columns in a few
cases. This converts haswell to hsw where appropriate.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191224084012.24241-3-lucas.demarchi@intel.com
The disable sequence after wait for transcoder off was not correctly
implemented.
The MST disable sequence is basically the same for HSW, SKL, ICL and
TGL, with just minor changes for TGL.
With this last patch we finally fixed the hotplugs triggered by MST
sinks during the disable/enable sequence, those were causing source
to try to do a link training while it was not ready causing CPU pipe
FIFO underrrus on TGL.
v2: Only unsetting TGL_TRANS_DDI_PORT_MASK for TGL on the post
disable sequence
v4: Rebased, moved MST sequences to intel_mst_post_disable_dp()
BSpec: 4231
BSpec: 4163
BSpec: 22243
BSpec: 49190
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191223010654.67037-4-jose.souza@intel.com
On TGL the blending of all the streams have moved from DDI to
transcoder, so now every transcoder working over the same MST port must
send its stream to a master transcoder and master will send to DDI
respecting the time slots.
So here adding all the CRTCs that shares the same MST stream if
needed and computing their state again, it will pick the lowest
pipe/transcoder among the ones in the same stream to be master.
Most of the time skl_commit_modeset_enables() enables pipes in a
crescent order but due DDB overlapping it might not happen, this
scenarios will be handled in the next patch.
v2:
- Using recently added intel_crtc_state_reset() to set
mst_master_transcoder to invalid transcoder for all non gen12 & MST
code paths
- Setting lowest pipe/transcoder as master, previously it was the
first one but setting a predictable one will help in future MST e
port sync integration
- Moving to intel type as much as we can
v3:
- Now intel_dp_mst_master_trans_compute() returns the MST master transcoder
- Replaced stdbool.h by linux/types.h
- Skip the connector being checked in
intel_dp_mst_atomic_master_trans_check()
- Using pipe instead of transcoder to compute MST master
v4:
- renamed connector_state to conn_state
v5:
- Improved the parameters of intel_dp_mst_master_trans_compute() to
simply code
- Added call drm_atomic_add_affected_planes() in
intel_dp_mst_atomic_master_trans_check() as helper could not do it
for us
- Removed "if (ret)" left over from v3 changes
v6:
- handled ret == I915_MAX_PIPES case in compute
BSpec: 50493
BSpec: 49190
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191223010654.67037-2-jose.souza@intel.com
Move all of haswell_crtc_disable() into the encoder
.post_disable() hooks. Now we're left with just
calling the .disable() and .post_disable() hooks
back to back.
I chose to move the code into the .post_disable() hook instead
of the .disable() hook as most of the sequence is currently
implemented in the .post_disable() hook.
We should collapse it all down to just one hook and then the
encoders can drive the modeset sequence fully. But that may
need some further refactoring as we currently call the
ddi .post_disable() hook from mst code and we can't just
replace that with a call to the ddi .disable() hook.
Should also follow up with similar treatment for the enable
sequence but let's start here where it's easier.
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213195217.15168-5-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
HSW+ platforms call encoder .post_disable() and .post_pll_disable()
back to back. And since we don't even disable the PLL in between
let's just move everything into .post_disable().
intel_dp_mst does forward the .post_disable() call to intel_ddi at
the very end of its own .post_disable() hook, so this time MST
I shouldn't even break MST by accident.
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213195217.15168-2-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Remove the pointless vfunc detour for hsw_fdi_link_train()
and just call it directly. Also pass the encoder in so we
can nuke the silly encoder loop within.
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213195217.15168-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Add basic hardware state readout for DSC, and check the most relevant
details in the state checker.
v2:
- check for DSC power before reading its state
- check if source supports DSC at all
As a side effect, this should also get the power domains for the enabled
DSC on takeover, and subsequently disable DSC if it's not needed.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/3fb018cf9bd9a4c275aab389b6ec0f2a4e938bb9.1575974743.git.jani.nikula@intel.com
intel_hdcp_transcoder_config() is clobbering some globally visible
state in .compute_config(). That is a big no no as .compute_config()
is supposed to have no visible side effects when either the commit
fails or it's just a TEST_ONLY commit.
Inline this stuff into intel_hdcp_enable() so that the state only
gets modified when we actually commit the state to the hardware.
Cc: Ramalingam C <ramalingam.c@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Fixes: 39e2df090c ("drm/i915/hdcp: update current transcoder into intel_hdcp")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191204180549.1267-2-ville.syrjala@linux.intel.com
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
For TGL the step to turn off the transcoder clock was moved to after
the complete shutdown of DDI. Only the MST slave transcoders should
disable the clock before that.
v2:
- Adding last_mst_stream to intel_mst_post_disable_dp, make code more
easy to read and is similar to first_mst_stream in
intel_mst_pre_enable_dp()(Ville's idea)
- Calling intel_ddi_disable_pipe_clock() for GEN12+ right
intel_disable_ddi_buf() as stated in BSpec(Ville)
BSpec: 49190
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191205210350.96795-2-jose.souza@intel.com
Disabling pipe/transcoder clock before power down sink could cause
sink lost signal, causing it to trigger a hotplug to notify source
that link signal was lost.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191202222513.337777-2-jose.souza@intel.com
The bspec initially provided a single DKL PHY vswing table for both HDMI
and DP, but was recently updated to include an independent table for
HDMI.
Bspec: 49292
Fixes: 978c3e539b ("drm/i915/tgl: Add dkl phy programming sequences")
Cc: Clinton A Taylor <clinton.a.taylor@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191118180219.9309-1-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
This register was being enabled after enable TRANS_DDI_FUNC_CTL and
PIPECONF/TRANS_CONF while BSpec states that it should be set when
enabling TRANS_DDI_FUNC_CTL.
BSpec: 49190
BSpec: 22243
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191107214559.77087-3-jose.souza@intel.com
