Fix the following coccicheck warning:
net/caif/caif_dev.c:410:2-13: WARNING: Assignment of 0/1 to bool
variable
net/caif/caif_dev.c:445:2-13: WARNING: Assignment of 0/1 to bool
variable
net/caif/caif_dev.c:145:1-12: WARNING: Assignment of 0/1 to bool
variable
net/caif/caif_dev.c:223:1-12: WARNING: Assignment of 0/1 to bool
variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For dwmac4, enable VLAN promiscuity when MAC controller is requested to
enter promiscuous mode.
Signed-off-by: Chuah, Kim Tatt <kim.tatt.chuah@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Tan, Tee Min <tee.min.tan@intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
macvlan_hash_lookup() uses list_for_each_entry_rcu() for traversing
should either under RCU in fast path or the protection of rtnl_mutex.
In the case of holding RTNL, we should add the corresponding lockdep
expression to silence the following false-positive warning:
=============================
WARNING: suspicious RCU usage
5.7.0-rc1-next-20200416-00003-ga3b8d28bc #1 Not tainted
-----------------------------
drivers/net/macvlan.c:126 RCU-list traversed in non-reader section!!
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add tests for vrf and xfrms with a second round after adding a
qdisc. There are a few known problems documented with the test
cases that fail. The fix is non-trivial; will come back to it
when time allows.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a qdisc is attached to the VRF device, the packet goes down the ndo
xmit function which is setup to send the packet back to the VRF driver
which does a lookup to send the packet out. The lookup in the VRF driver
is not considering xfrm policies. Change it to use ip6_dst_lookup_flow
rather than ip6_route_output.
Fixes: 35402e3136 ("net: Add IPv6 support to VRF device")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for non-root users to send ICMP ECHO requests was added
back in Linux 3.0 kernel, but the documentation for the sysctl
to enable it has been missing.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jere Leppänen says:
====================
sctp: Fix problems with peer restart when in SHUTDOWN-PENDING state and socket is closed
These patches are related to the scenario described in commit
bdf6fa52f0 ("sctp: handle association restarts when the socket is
closed."). To recap, when our association is in SHUTDOWN-PENDING state
and we've closed our one-to-one socket, while the peer crashes without
being detected, restarts and reconnects using the same addresses and
ports, we start association shutdown.
In this case, Cumulative TSN Ack in the SHUTDOWN that we send has
always been incorrect. Additionally, bundling of the SHUTDOWN with the
COOKIE-ACK was broken by a later commit. This series fixes both of
these issues.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When starting shutdown in sctp_sf_do_dupcook_a(), get the value for
SHUTDOWN Cumulative TSN Ack from the new association, which is
reconstructed from the cookie, instead of the old association, which
the peer doesn't have anymore.
Otherwise the SHUTDOWN is either ignored or replied to with an ABORT
by the peer because CTSN Ack doesn't match the peer's Initial TSN.
Fixes: bdf6fa52f0 ("sctp: handle association restarts when the socket is closed.")
Signed-off-by: Jere Leppänen <jere.leppanen@nokia.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we start shutdown in sctp_sf_do_dupcook_a(), we want to bundle
the SHUTDOWN with the COOKIE-ACK to ensure that the peer receives them
at the same time and in the correct order. This bundling was broken by
commit 4ff40b8626 ("sctp: set chunk transport correctly when it's a
new asoc"), which assigns a transport for the COOKIE-ACK, but not for
the SHUTDOWN.
Fix this by passing a reference to the COOKIE-ACK chunk as an argument
to sctp_sf_do_9_2_start_shutdown() and onward to
sctp_make_shutdown(). This way the SHUTDOWN chunk is assigned the same
transport as the COOKIE-ACK chunk, which allows them to be bundled.
In sctp_sf_do_9_2_start_shutdown(), the void *arg parameter was
previously unused. Now that we're taking it into use, it must be a
valid pointer to a chunk, or NULL. There is only one call site where
it's not, in sctp_sf_autoclose_timer_expire(). Fix that too.
Fixes: 4ff40b8626 ("sctp: set chunk transport correctly when it's a new asoc")
Signed-off-by: Jere Leppänen <jere.leppanen@nokia.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now it can be seen that the VSC9959 (Felix) switch will not flood
frames if they have a VLAN tag with a PCP of 1-7 (nonzero).
It turns out that Felix is quite different from its cousin, Ocelot, in
that frame flooding can be allowed/denied per traffic class. Where
Ocelot has 1 instance of the ANA_FLOODING register, Felix has 8.
The approach that this driver is going to take is "thanks, but no
thanks". We have no use case of limiting the flooding domain based on
traffic class, so we just want to allow packets to be flooded, no matter
what traffic class they have.
So we copy the line of code from ocelot.c which does the one-shot
initialization of the flooding PGIDs, and we add it to felix.c as well -
except replicated 8 times.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no reason to fail the probing of the switch if the MTU couldn't
be configured correctly (either the switch port itself, or the host
port) for whatever reason. MTU-sized traffic probably won't work, sure,
but we can still probably limp on and support some form of communication
anyway, which the users would probably appreciate more.
Fixes: bfcb813203 ("net: dsa: configure the MTU for switch ports")
Reported-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following sparse warning:
kernel/trace/tracing_map.c:286:6: warning: symbol
'tracing_map_array_clear' was not declared. Should it be static?
kernel/trace/tracing_map.c:297:6: warning: symbol
'tracing_map_array_free' was not declared. Should it be static?
kernel/trace/tracing_map.c:319:26: warning: symbol
'tracing_map_array_alloc' was not declared. Should it be static?
Link: http://lkml.kernel.org/r/20200410073312.38855-1-yanaijie@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
This macro was intentionally broken so that the kernel code is not
poluted with such noargs macro used simply as markers. This use case
can be satisfied by using dummy no inline functions. Just remove it.
Link: http://lkml.kernel.org/r/20200413153246.8511-1-nborisov@suse.com
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
As the bug report [1] pointed out, <linux/vermagic.h> must be included
after <linux/module.h>.
I believe we should not impose any include order restriction. We often
sort include directives alphabetically, but it is just coding style
convention. Technically, we can include header files in any order by
making every header self-contained.
Currently, arch-specific MODULE_ARCH_VERMAGIC is defined in
<asm/module.h>, which is not included from <linux/vermagic.h>.
Hence, the straight-forward fix-up would be as follows:
|--- a/include/linux/vermagic.h
|+++ b/include/linux/vermagic.h
|@@ -1,5 +1,6 @@
| /* SPDX-License-Identifier: GPL-2.0 */
| #include <generated/utsrelease.h>
|+#include <linux/module.h>
|
| /* Simply sanity version stamp for modules. */
| #ifdef CONFIG_SMP
This works enough, but for further cleanups, I split MODULE_ARCH_VERMAGIC
definitions into <asm/vermagic.h>.
With this, <linux/module.h> and <linux/vermagic.h> will be orthogonal,
and the location of MODULE_ARCH_VERMAGIC definitions will be consistent.
For arc and ia64, MODULE_PROC_FAMILY is only used for defining
MODULE_ARCH_VERMAGIC. I squashed it.
For hexagon, nds32, and xtensa, I removed <asm/modules.h> entirely
because they contained nothing but MODULE_ARCH_VERMAGIC definition.
Kbuild will automatically generate <asm/modules.h> at build-time,
wrapping <asm-generic/module.h>.
[1] https://lore.kernel.org/lkml/20200411155623.GA22175@zn.tnic
Reported-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Acked-by: Jessica Yu <jeyu@kernel.org>
Since commit 7a04960560 ("kbuild: fix DT binding schema rule to detect
command line changes"), this rule is every time re-run even if you change
nothing.
cmd_dtc takes one additional parameter to pass to the -O option of dtc.
We need to pass 'yaml' to if_changed_rule. Otherwise, cmd-check invoked
from if_changed_rule is false positive.
Fixes: 7a04960560 ("kbuild: fix DT binding schema rule to detect command line changes")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Sometimes, WARN_FUNC() and other users of symbol_by_offset() will
associate the first instruction of a symbol with the symbol preceding
it. This is because symbol->offset + symbol->len is already outside of
the symbol's range.
Fixes: 2a362ecc3e ("objtool: Optimize find_symbol_*() and read_symbols()")
Signed-off-by: Julien Thierry <jthierry@redhat.com>
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
uclamp_fork() resets the uclamp values to their default when the
reset-on-fork flag is set. It also checks whether the task has a RT
policy, and sets its uclamp.min to 1024 accordingly. However, during
reset-on-fork, the task's policy is lowered to SCHED_NORMAL right after,
hence leading to an erroneous uclamp.min setting for the new task if it
was forked from RT.
Fix this by removing the unnecessary check on rt_task() in
uclamp_fork() as this doesn't make sense if the reset-on-fork flag is
set.
Fixes: 1a00d99997 ("sched/uclamp: Set default clamps for RT tasks")
Reported-by: Chitti Babu Theegala <ctheegal@codeaurora.org>
Signed-off-by: Quentin Perret <qperret@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Patrick Bellasi <patrick.bellasi@matbug.net>
Reviewed-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Link: https://lkml.kernel.org/r/20200416085956.217587-1-qperret@google.com
Improve readability of the function intel_set_max_freq_ratio() by moving
the check for KNL CPUs there, together with checks for GLM and SKX.
Signed-off-by: Giovanni Gherdovich <ggherdovich@suse.cz>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lkml.kernel.org/r/20200416054745.740-5-ggherdovich@suse.cz
The static key arch_scale_freq_key only needs to be enabled once (at
boot). This change fixes a bug by which the key was enabled every time cpu0
is started, even as a secondary CPU during cpu hotplug. Secondary CPUs are
started from the idle thread: setting a static key from there means
acquiring a lock and may result in sleeping in the idle task, causing CPU
lockup.
Another consequence of this change is that init_counter_refs() is now
called on each CPU correctly; previously the function on_each_cpu() was
used, but it was called at boot when the only online cpu is cpu0.
[ggherdovich@suse.cz: Tested and wrote changelog]
Fixes: 1567c3e346 ("x86, sched: Add support for frequency invariance")
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Giovanni Gherdovich <ggherdovich@suse.cz>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lkml.kernel.org/r/20200416054745.740-4-ggherdovich@suse.cz
If a CPU has less than 4 physical cores, MSR_TURBO_RATIO_LIMIT will
rightfully report that the 4C turbo ratio is zero. In such cases, use the
1C turbo ratio instead for frequency invariance calculations.
Fixes: 1567c3e346 ("x86, sched: Add support for frequency invariance")
Reported-by: Like Xu <like.xu@linux.intel.com>
Reported-by: Neil Rickert <nwr10cst-oslnx@yahoo.com>
Signed-off-by: Giovanni Gherdovich <ggherdovich@suse.cz>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Link: https://lkml.kernel.org/r/20200416054745.740-3-ggherdovich@suse.cz
Some hypervisors such as VMWare ESXi 5.5 advertise support for
X86_FEATURE_APERFMPERF but then fill all MSR's with zeroes. In particular,
MSR_PLATFORM_INFO set to zero tricks the code that wants to know the base
clock frequency of the CPU (highest non-turbo frequency), producing a
division by zero when computing the ratio turbo_freq/base_freq necessary
for frequency invariant accounting.
It is to be noted that even if MSR_PLATFORM_INFO contained the appropriate
data, APERF and MPERF are constantly zero on ESXi 5.5, thus freq-invariance
couldn't be done in principle (not that it would make a lot of sense in a
VM anyway). The real problem is advertising X86_FEATURE_APERFMPERF. This
appears to be fixed in more recent versions: ESXi 6.7 doesn't advertise
that feature.
Fixes: 1567c3e346 ("x86, sched: Add support for frequency invariance")
Signed-off-by: Giovanni Gherdovich <ggherdovich@suse.cz>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lkml.kernel.org/r/20200416054745.740-2-ggherdovich@suse.cz
fib_tests is spewing errors:
...
Cannot open network namespace "ns1": No such file or directory
Cannot open network namespace "ns1": No such file or directory
Cannot open network namespace "ns1": No such file or directory
Cannot open network namespace "ns1": No such file or directory
ping: connect: Network is unreachable
Cannot open network namespace "ns1": No such file or directory
Cannot open network namespace "ns1": No such file or directory
...
Each test entry in fib_tests is supposed to do its own setup and
cleanup. Right now the $IP commands in fib_suppress_test are
failing because there is no ns1. Add the setup/cleanup and logging
expected for each test.
Fixes: ca7a03c417 ("ipv6: do not free rt if FIB_LOOKUP_NOREF is set on suppress rule")
Signed-off-by: David Ahern <dsahern@gmail.com>
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add tracepoint support for QRTR with NS as the first candidate. Later on
this can be extended to core QRTR and transport drivers.
The trace_printk() used in NS has been replaced by tracepoints.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
net: dsa: b53: Various ARL fixes
This patch series fixes a number of short comings in the existing b53
driver ARL management logic in particular:
- we were not looking up the {MAC,VID} tuples against their VID, despite
having VLANs enabled
- the MDB entries (multicast) would lose their validity as soon as a
single port in the vector would leave the entry
- the ARL was currently under utilized because we would always place new
entries in bin index #1, instead of using all possible bins available,
thus reducing the ARL effective size by 50% or 75% depending on the
switch generation
- it was possible to overwrite the ARL entries because no proper space
verification was done
This patch series addresses all of these issues.
Changes in v2:
- added a new patch to correctly flip invidual VLAN learning vs. shared
VLAN learning depending on the global VLAN state
- added Andrew's R-b tags for patches which did not change
- corrected some verbosity and minor issues in patch #4 to match caller
expectations, also avoid a variable length DECLARE_BITMAP() call
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Flip the IVL_SVL_SELECT bit correctly based on the VLAN enable status,
the default is to perform Shared VLAN learning instead of Individual
learning.
Fixes: 1da6df85c6 ("net: dsa: b53: Implement ARL add/del/dump operations")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When asking the ARL to read a MAC address, we will get a number of bins
returned in a single read. Out of those bins, there can essentially be 3
states:
- all bins are full, we have no space left, and we can either replace an
existing address or return that full condition
- the MAC address was found, then we need to return its bin index and
modify that one, and only that one
- the MAC address was not found and we have a least one bin free, we use
that bin index location then
The code would unfortunately fail on all counts.
Fixes: 1da6df85c6 ("net: dsa: b53: Implement ARL add/del/dump operations")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ARL {MAC,VID} tuple and the forward entry were off by 0x10 bytes,
which means that when we read/wrote from/to ARL bin index 0, we were
actually accessing the ARLA_RWCTRL register.
Fixes: 1da6df85c6 ("net: dsa: b53: Implement ARL add/del/dump operations")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When support for the MDB entries was added, the valid bit was correctly
changed to be assigned depending on the remaining port bitmask, that is,
if there were no more ports added to the entry's port bitmask, the entry
now becomes invalid. There was another assignment a few lines below that
would override this which would invalidate entries even when there were
still multiple ports left in the MDB entry.
Fixes: 5d65b64a3d ("net: dsa: b53: Add support for MDB")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VLAN is enabled, and an ARL search is issued, we also need to
compare the full {MAC,VID} tuple before returning a successful search
result.
Fixes: 1da6df85c6 ("net: dsa: b53: Implement ARL add/del/dump operations")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/ipv6/ila/ila_xlat.c:604:0: warning: macro "ILA_HASH_TABLE_SIZE" is not used [-Wunused-macros]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the act_ct SW offload in flowtable, The counter of the conntrack
entry will never update. So update the nf_conn_acct conuter in act_ct
flowtable software offload.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern says:
====================
net: Fix looping with vrf, xfrms and qdisc on VRF
Trev reported that use of VRFs with xfrms is looping when a qdisc
is added to the VRF device. The combination of xfrm + qdisc is not
handled by the VRF driver which lost track that it has already
seen the packet.
The XFRM_TRANSFORMED flag is used by the netfilter code for a similar
purpose, so re-use for VRF. Patch 1 drops the #ifdef around setting
the flag in the xfrm output functions. Patch 2 adds a check to
the VRF driver for flag; if set the packet has already passed through
the VRF driver once and does not need to recirculated a second time.
This is a day 1 bug with VRFs; stable wise, I would only take this
back to 4.14. I have a set of test cases which I will submit to
net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid a loop with qdiscs and xfrms, check if the skb has already gone
through the qdisc attached to the VRF device and then to the xfrm layer.
If so, no need for a second redirect.
Fixes: 193125dbd8 ("net: Introduce VRF device driver")
Reported-by: Trev Larock <trev@larock.ca>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPSKB_XFRM_TRANSFORMED and IP6SKB_XFRM_TRANSFORMED are skb flags set by
xfrm code to tell other skb handlers that the packet has been passed
through the xfrm output functions. Simplify the code and just always
set them rather than conditionally based on netfilter enabled thus
making the flag available for other users.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit says:
====================
net: phy: add device-managed devm_mdiobus_register
If there's no special ordering requirement for mdiobus_unregister(),
then driver code can be simplified by using a device-managed version
of mdiobus_register(). Prerequisite is that bus allocation has been
done device-managed too. Else mdiobus_free() may be called whilst
bus is still registered, resulting in a BUG_ON(). Therefore let
devm_mdiobus_register() return -EPERM if bus was allocated
non-managed.
First user of the new functionality is r8169 driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new function devm_mdiobus_register() to simplify the driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there's no special ordering requirement for mdiobus_unregister(),
then driver code can be simplified by using a device-managed version
of mdiobus_register(). Prerequisite is that bus allocation has been
done device-managed too. Else mdiobus_free() may be called whilst
bus is still registered, resulting in a BUG_ON(). Therefore let
devm_mdiobus_register() return -EPERM if bus was allocated
non-managed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
See:
https://www.rfc-editor.org/authors/rfc8781.txt
Cc: Erik Kline <ek@google.com>
Cc: Jen Linkova <furry@google.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: Michael Haro <mharo@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Fixes: c24a77edc9 ("ipv6: ndisc: add support for 'PREF64' dns64 prefix identifier")
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY supports monitoring its die temperature as well as two analog
voltages. Add support for it.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Broadcom BCM54140 is a Quad SGMII/QSGMII Copper/Fiber Gigabit
Ethernet transceiver.
This also adds support for tunables to set and get downshift and
energy detect auto power-down.
The PHY has four ports and each port has its own PHY address.
There are per-port registers as well as global registers.
Unfortunately, the global registers can only be accessed by reading
and writing from/to the PHY address of the first port. Further,
there is no way to find out what port you actually are by just
reading the per-port registers. We therefore, have to scan the
bus on the PHY probe to determine the port and thus what address
we need to access the global registers.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
RDB (Register Data Base) registers are used on newer Broadcom PHYs. Add
helper to read, write and modify these registers.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
dt-bindings: net: mdio.yaml fixes
This patch series documents some common MDIO devices properties such as
resets (and delays) and broken-turn-around. The second patch also
rephrases some descriptions to be more general towards MDIO devices and
not specific towards Ethernet PHYs.
Changes in v3:
- corrected wording of 'broken-turn-around' in ethernet-phy.yaml and
mdio.yaml, add Andrew's R-b tag to patch #3
====================
Signed-off-by: David S. Miller <davem@davemloft.net>