The Marvell Switches support jumbo packages. So implement the
callbacks needed for changing the MTU.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flow spec member vlan_tci is in network order. Hence comparisons
should be made again network order values.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
One way of utilizing DSA is by cascading switches which do not all have
compatible taggers. Consider the following real-life topology:
+---------------------------------------------------------------+
| LS1028A |
| +------------------------------+ |
| | DSA master for Felix | |
| |(internal ENETC port 2: eno2))| |
| +------------+------------------------------+-------------+ |
| | Felix embedded L2 switch | |
| | | |
| | +--------------+ +--------------+ +--------------+ | |
| | |DSA master for| |DSA master for| |DSA master for| | |
| | | SJA1105 1 | | SJA1105 2 | | SJA1105 3 | | |
| | |(Felix port 1)| |(Felix port 2)| |(Felix port 3)| | |
+--+-+--------------+---+--------------+---+--------------+--+--+
+-----------------------+ +-----------------------+ +-----------------------+
| SJA1105 switch 1 | | SJA1105 switch 2 | | SJA1105 switch 3 |
+-----+-----+-----+-----+ +-----+-----+-----+-----+ +-----+-----+-----+-----+
|sw1p0|sw1p1|sw1p2|sw1p3| |sw2p0|sw2p1|sw2p2|sw2p3| |sw3p0|sw3p1|sw3p2|sw3p3|
+-----+-----+-----+-----+ +-----+-----+-----+-----+ +-----+-----+-----+-----+
The above can be described in the device tree as follows (obviously not
complete):
mscc_felix {
dsa,member = <0 0>;
ports {
port@4 {
ethernet = <&enetc_port2>;
};
};
};
sja1105_switch1 {
dsa,member = <1 1>;
ports {
port@4 {
ethernet = <&mscc_felix_port1>;
};
};
};
sja1105_switch2 {
dsa,member = <2 2>;
ports {
port@4 {
ethernet = <&mscc_felix_port2>;
};
};
};
sja1105_switch3 {
dsa,member = <3 3>;
ports {
port@4 {
ethernet = <&mscc_felix_port3>;
};
};
};
Basically we instantiate one DSA switch tree for every hardware switch
in the system, but we still give them globally unique switch IDs (will
come back to that later). Having 3 disjoint switch trees makes the
tagger drivers "just work", because net devices are registered for the
3 Felix DSA master ports, and they are also DSA slave ports to the ENETC
port. So packets received on the ENETC port are stripped of their
stacked DSA tags one by one.
Currently, hardware bridging between ports on the same sja1105 chip is
possible, but switching between sja1105 ports on different chips is
handled by the software bridge. This is fine, but we can do better.
In fact, the dsa_8021q tag used by sja1105 is compatible with cascading.
In other words, a sja1105 switch can correctly parse and route a packet
containing a dsa_8021q tag. So if we could enable hardware bridging on
the Felix DSA master ports, cross-chip bridging could be completely
offloaded.
Such as system would be used as follows:
ip link add dev br0 type bridge && ip link set dev br0 up
for port in sw0p0 sw0p1 sw0p2 sw0p3 \
sw1p0 sw1p1 sw1p2 sw1p3 \
sw2p0 sw2p1 sw2p2 sw2p3; do
ip link set dev $port master br0
done
The above makes switching between ports on the same row be performed in
hardware, and between ports on different rows in software. Now assume
the Felix switch ports are called swp0, swp1, swp2. By running the
following extra commands:
ip link add dev br1 type bridge && ip link set dev br1 up
for port in swp0 swp1 swp2; do
ip link set dev $port master br1
done
the CPU no longer sees packets which traverse sja1105 switch boundaries
and can be forwarded directly by Felix. The br1 bridge would not be used
for any sort of traffic termination.
For this to work, we need to give drivers an opportunity to listen for
bridging events on DSA trees other than their own, and pass that other
tree index as argument. I have made the assumption, for the moment, that
the other existing DSA notifiers don't need to be broadcast to other
trees. That assumption might turn out to be incorrect. But in the
meantime, introduce a dsa_broadcast function, similar in purpose to
dsa_port_notify, which is used only by the bridging notifiers.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
These struct members named 'phylink_validate' was assigned twice:
static const struct mv88e6xxx_ops mv88e6190_ops = {
......
.phylink_validate = mv88e6390_phylink_validate,
......
.phylink_validate = mv88e6390_phylink_validate,
};
static const struct mv88e6xxx_ops mv88e6190x_ops = {
......
.phylink_validate = mv88e6390_phylink_validate,
......
.phylink_validate = mv88e6390x_phylink_validate,
};
static const struct mv88e6xxx_ops mv88e6191_ops = {
......
.phylink_validate = mv88e6390_phylink_validate,
......
.phylink_validate = mv88e6390_phylink_validate,
};
static const struct mv88e6xxx_ops mv88e6290_ops = {
......
.phylink_validate = mv88e6390_phylink_validate,
......
.phylink_validate = mv88e6390_phylink_validate,
};
Remove all the first one and leave the second one which are been used in
fact. Be aware that for 'mv88e6190x_ops' the assignment functions is
different while the others are all the same. This fixes the following
coccicheck warning:
drivers/net/dsa/mv88e6xxx/chip.c:3911:48-49: phylink_validate: first
occurrence line 3965, second occurrence line 3967
drivers/net/dsa/mv88e6xxx/chip.c:3970:49-50: phylink_validate: first
occurrence line 4024, second occurrence line 4026
drivers/net/dsa/mv88e6xxx/chip.c:4029:48-49: phylink_validate: first
occurrence line 4082, second occurrence line 4085
drivers/net/dsa/mv88e6xxx/chip.c:4184:48-49: phylink_validate: first
occurrence line 4238, second occurrence line 4242
Fixes: 4262c38dc4 ("net: dsa: mv88e6xxx: Add SERDES stats counters to all 6390 family members")
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 88e6185 is reporting it has detected a PHY, when a port is
connected to an SFP. As a result, the fixed-phy configuration is not
being applied. That then breaks packet transfer, since the port is
reported as being down.
Add additional conditions to check the interface mode, and if it is
fixed always configure the port on link up/down, independent of the
PPU status.
Fixes: 30c4a5b0aa ("net: mv88e6xxx: use resolved link config in mac_link_up()")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the status of the PHY_DETECT bit to determine whether we need to
force the MAC settings in mac_link_up() and mac_link_down().
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port_link_state method is only used by mv88e6xxx_port_setup_mac(),
which is now only called during port setup, rather than also being
called via phylink's mac_config method.
Remove this now unnecessary optimisation, which allows us to remove the
port_link_state methods as well.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting the speed independently of duplex makes little sense; the two
parameters result from negotiation or fixed setup, and may have inter-
dependencies. Moreover, they are always controlled via the same
register - having them split means we have to read-modify-write this
register twice.
Combine the two operations into a single port_set_speed_duplex()
operation. Not only is this more efficient, it reduces the size of the
code as well.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the mv88e6xxx phylink implementation down to Serdes PHYs, which
handle the PCS layer of such links.
- Implement phylink PCS link state reading, so that we can provide
ethtool with the linkmodes and link speed in the expected manner.
Note: this will only be called for in-band negotiation, which is
only supported by the serdes interfaces.
- Implement phylink PCS configuration, so that the in-band AN and
advertisement can be configured.
- Implement phylink PCS negotiation restart, so that the in-band AN
can be restarted.
- Implement phylink PCS link up, so that when operating out-of-band,
the Serdes can be configured for the appropriate fixed speed mode.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only configure the interface settings in mac_config(), leaving the
speed and duplex settings to mac_link_up to deal with.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the bottom 12 bits contain the ATU bin occupancy statistics. The
upper bits need masking off.
Fixes: e0c69ca7df ("net: dsa: mv88e6xxx: Add ATU occupancy via devlink resources")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the resolved link configuration to set the MAC configuration when
mac_link_up() for non-internal-PHY ports.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Propagate the resolved link configuration down via DSA's
phylink_mac_link_up() operation to allow split PCS/MAC to work.
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting VLANs on DSA switches, the VLAN is added to both the port
concerned as well as the CPU port by dsa_slave_vlan_add(), as well as
any DSA ports. If multiple ports are configured with the same VLAN ID,
this triggers a warning on the CPU and DSA ports.
Avoid this warning for CPU and DSA ports.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390 has upto 8 sets of PCS registers, depending on how ports
9 and 10 are configured. The can be spread over 8 ports. If a port has
a PCS register set, return it along with the port registers. The
register space is sparse, so hard code a list of registers which will
be returned. It can later be extended, if needed, by append to the end
of the list.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6352 has one PCS which can be used for 1000BaseX or
SGMII. Add the registers to the dump for the port which the PCS is
associated to.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool provides a generic mechanism for a driver to return the
registers of an ethernet device. DSA uses this to give the port
registers associated with an interfaces. Extend this to allow PCS
registers to also be returned, if the port has a PCS associated to it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SERDES statistics are valid for all members of the 6390 family,
not just the 6390 itself. Add the needed callbacks to all members of
the family.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible to stack multiple DSA switches in a way that they are not
part of the tree (disjoint) but the DSA master of a switch is a DSA
slave of another. When that happens switch drivers may have to know this
is the case so as to determine whether their tagging protocol has a
remove chance of working.
This is useful for specific switch drivers such as b53 where devices
have been known to be stacked in the wild without the Broadcom tag
protocol supporting that feature. This allows b53 to continue supporting
those devices by forcing the disabling of Broadcom tags on the outermost
switches if necessary.
The get_tag_protocol() function is therefore updated to gain an
additional enum dsa_tag_protocol argument which denotes the current
tagging protocol used by the DSA master we are attached to, else
DSA_TAG_PROTO_NONE for the top of the dsa_switch_tree.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dynamically generate a unique SERDES interrupt name, based on the
device name and the port the SERDES is for. For example:
95: 3 mv88e6xxx-g2 9 Edge mv88e6xxx-0.2:00-serdes-9
96: 0 mv88e6xxx-g2 10 Edge mv88e6xxx-0.2:00-serdes-10
The 0.2:00 indicates the switch and -9 indicates port 9.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dynamically generate a unique switch interrupt name, based on the
device name.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If packet checker is enabled in the serdes, then Rx counter registers
start working, and no side effects have been detected.
This patch enables packet checker automatically when powering serdes on,
and exposes Rx counter registers via ethtool statistics interface.
Code partially basded by older attempt by Andrew Lunn.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a stray semicolon in an if statement that will cause a dev_err
message to be printed unconditionally. Fix this by removing the stray
semicolon.
Addresses-Coverity: ("Stay semicolon")
Fixes: f0942e00a1 ("net: dsa: mv88e6xxx: Add support for port mirroring")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuring port mirroring through the cls_matchall
classifier. We do a full ingress and/or egress capture towards a
capture port. It allows setting a different capture port for ingress
and egress traffic.
It keeps track of the mirrored ports and the destination ports to
prevent changes to the capture port while other ports are being
mirrored.
Signed-off-by: Iwan R Timmer <irtimmer@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate the configuration of the egress and ingress monitor port.
This allows the port mirror functionality to do ingress and egress
port mirroring to separate ports.
Signed-off-by: Iwan R Timmer <irtimmer@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ATU can report how many entries it contains. It does this per bin,
there being 4 bins in total. Export the ATU as a devlink resource, and
provide a method the needed callback to get the resource occupancy.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For each supported switch, add an entry to the info structure for the
number of MACs which can be stored in the ATU. This will later be used
to export the ATU as a devlink resource, and indicate its occupancy,
how full the ATU is.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement a new list of DSA links in the switch fabric itself, to
provide an alterative to the ds->rtable static arrays.
At the same time, provide a new dsa_routing_port() helper to abstract
the usage of ds->rtable in drivers. If there's no port to reach a
given device, return the first invalid port, ds->num_ports. This avoids
potential signedness errors or the need to define special values.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the marvell switches have bits controlling the hash algorithm
the ATU uses for MAC addresses. In some industrial settings, where all
the devices are from the same manufacture, and hence use the same OUI,
the default hashing algorithm is not optimal. Allow the other
algorithms to be selected via devlink.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that ports are dynamically listed in the fabric, there is no need
to provide a special helper to allocate the dsa_switch structure. This
will give more flexibility to drivers to embed this structure as they
wish in their private structure.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Instead of digging into the other dsa_switch structures of the fabric
and relying too much on the dsa_to_port helper, use the new list
of switch fabric ports to remap the Port VLAN Map of local bridge
group members or remap the Port VLAN Table entry of external bridge
group members.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Instead of digging into the other dsa_switch structures of the fabric
and relying too much on the dsa_to_port helper, use the new list of
switch fabric ports to define the mask of the local ports allowed to
receive frames from another port of the fabric.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Since mv88e6xxx_pvt_map is a static helper, no need to return
-EOPNOTSUPP if the chip has no PVT, simply silently skip the operation.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Do not let the drivers access the ds->ports static array directly
while there is a dsa_to_port helper for this purpose.
At the same time, un-const this helper since the SJA1105 driver
assigns the priv member of the returned dsa_port structure.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Implement the .get_rxnfc and .set_rxnfc DSA operations to configure
a port's Layer 2 Policy Control List (PCL) via ethtool.
Currently only dropping frames based on MAC Destination or Source
Address (including the option VLAN parameter) is supported.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new .port_set_policy operation to configure a port's
Policy Control List, based on mapping such as DA, SA, Etype and so on.
Models similar to 88E6352 and 88E6390 are supported at the moment.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell has different values for the state of a MAC address,
depending on its multicast bit. This patch completes the definitions
for these states.
At the same time, use 0 which is intuitive enough and simplifies the
code a bit, instead of the UC or MC unused value.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The .serdes_irq_setup are all following the same steps: get the SERDES
lane, get the IRQ mapping, request the IRQ, then enable it. So do
the .serdes_irq_free implementations: get the SERDES lane, disable
the IRQ, then free it.
This patch removes these operations in favor of generic functions.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new .serdes_irq_status operation to prepare the abstraction
of IRQ thread from the SERDES IRQ setup code.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new .serdes_irq_enable operation to prepare the abstraction
of IRQ enabling from the SERDES IRQ setup code.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now the first step of all .serdes_power implementations is getting
the lane mapping. Since we have an operation for that, call it in
the wrapper and pass the lane down to the .serdes_power operation.
This also allows to avoid querying the SERDES lane twice in
mv88e6xxx_port_set_cmode.
At the same time provide mv88e6xxx_serdes_power_{up,down} helpers
and prefer up/down instead of on/off as in the documentation.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even though 88E6352 has no dedicated lane for SERDES interfaces, it
uses a similar code as the other .serdes_get_lane implementations to
check the port's CMODE and ensure that SERDES operations are doable.
For consistency, implement mv88e6352_serdes_get_lane for the 88E6352
and similar switches which simply returns an unused 0xff lane address.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new .serdes_irq_mapping operation to prepare the
abstraction of IRQ mapping from the SERDES IRQ setup code.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now mv88e6xxx does not enable its ports at setup itself and let
the DSA core handle this, unused ports are disabled without being
powered on first. While that is expected, the SERDES powering code
was assuming that a port was already set up before powering it down,
resulting in freeing an unused IRQ. The patch fixes this assumption.
Fixes: b759f528ca ("net: dsa: mv88e6xxx: enable SERDES after setup")
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a follow-up patch for commit 7a3007d22e ("net: dsa:
mv88e6xxx: fully support SERDES on Topaz family").
Since .port_set_cmode is only called from mv88e6xxx_port_setup_mac and
mv88e6xxx_phylink_mac_config, it is fine to keep this "make writable"
code private to the mv88e6341_port_set_cmode implementation, instead
of adding yet another operation to the switch info structure.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we support SERDES on the Topaz family in a limited way: no
IRQs and the cmode is not writable, thus the mode is determined by
strapping pins.
Marvell's examples though show how to make cmode writable on port 5 and
support SGMII autonegotiation. It is done by writing hidden registers,
for which we already have code.
This patch adds support for making the cmode for the SERDES port
writable on the Topaz family, via a new chip operation,
.port_set_cmode_writable, which is called from mv88e6xxx_port_setup_mac
just before .port_set_cmode.
SERDES IRQs are also enabled for Topaz.
Tested on Turris Mox.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
By adding an additional serdes_get_lane implementation (for Topaz), we
can merge the implementations of other SERDES functions (powering and
IRQs). We can skip checking port numbers, since the serdes_get_lane()
methods inform if there is no lane on a port or if the lane cannot be
used for given cmode.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a serdes_get_lane() method in the mv88e6xxx operations structure.
Use it instead of calling the different implementations.
Also change the methods so that their return value is used only for
error. The lane number is put into a place referred to by a pointer
given as argument. If the port does not have a lane, return -ENODEV.
Lanes are phy addresses, so use u8 as their type.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the functions operating on the hidden debug registers
into it's own file, port_hidden.c. The functions prefix is renamed from
mv88e6390_hidden_ to mv88e6xxx_port_hidden_, to be consistent with the
rest of this driver. The macros are prefixed with MV88E6XXX_ prefix, and
are changed not to use the BIT() macro nor bit shifts, since the rest of
the port.h file does not use it.
We also add the support for setting the Block Address field when
operating hidden registers. Marvell's mdio examples for SERDES settings
on Topaz use Block Address 0x7 when reading/writing hidden registers,
and although the specification says that block must be set to 0xf, those
settings are reachable only with Block Address 0x7.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
