Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2020-06-25
This series contains updates to i40e driver and removes the individual
driver versions from all of the Intel wired LAN drivers.
Shiraz moves the client header so that it can easily be shared between
the i40e LAN driver and i40iw RDMA driver.
Jesse cleans up the unused defines, since they are just dead weight.
Alek reduces the unreasonably long wait time for a PF reset after reboot
by using jiffies to limit the maximum wait time for the PF reset to
succeed. Added additional logging to let the user know when the driver
transitions into recovery mode. Adds new device support for our 5 Gbps
NICs.
Todd adds a check to see if MFS is set after warm reboot and notifies
the user when MFS is set to anything lower than the default value.
Arkadiusz fixes a possible race condition, where were holding a
spin-lock while in atomic context.
v2: removed code comments that were no longer applicable in patch 2 of
the series. Also removed 'inline' from patch 4 and patch 8 of the
series. Also re-arranged code to be able to remove the forward
function declarations. Dropped patch 9 of the series, while the
author works on cleaning up the commit message.
v3: Updated patch 8 description to answer Jakub's questions
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
As with other networking drivers, remove the unnecessary driver version
from the Intel drivers. The ethtool driver information and module version
will then report the kernel version instead.
For ixgbe, i40e and ice drivers, the driver passes the driver version to
the firmware to confirm that we are up and running. So we now pass the
value of UTS_RELEASE to the firmware. This adminq call is required per
the HAS document. The Device then sends an indication to the BMC that the
PF driver is present. This is done using Host NC Driver Status Indication
in NC-SI Get Link command or via the Host Network Controller Driver Status
Change AEN.
What the BMC may do with this information is implementation-dependent, but
this is a standard NC-SI 1.1 command we honor per the HAS.
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Alek Loktionov <aleksandr.loktionov@intel.com>
CC: Kevin Liedtke <kevin.d.liedtke@intel.com>
CC: Aaron Rowden <aaron.f.rowden@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Co-developed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
The READ_ONCE macro is used when reading rings prior to accessing the
statistics pointer. The corresponding WRITE_ONCE usage when allocating and
freeing the rings to ensure protected access was not in place. Introduce
this.
Signed-off-by: Ciara Loftus <ciara.loftus@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When setting the PHY cfg (CQ cmd 0x0601), if the firmware responds
with an EMODE error, software will ignore the error as it simply
means that manageability (ex: BMC) is in control of the link and that
the new setting may not be applied.
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit ceb2f00707 ("ice: Use pci_get_dsn()") changed the code to
use a new function to get the Device Serial Number. It also changed
the case of the filename for loading a package on a specific NIC
from lowercase to uppercase. Change the filename back to
lowercase since that is what we specified.
Fixes: ceb2f00707 ("ice: Use pci_get_dsn()")
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently VF VSI are being reset twice during a PFR or greater. This is
causing reset, specifically resetting all VFs, to take too long. This is
causing various issues with VF drivers not being able to gracefully
handle the VF reset timeout. Fix this by refactoring how VF reset is
handled for the case mentioned previously and for the VFR/VFLR case.
The refactor was done by doing the following:
1. Removing the call to ice_vsi_rebuild_by_type for
ICE_VSI_VF VSI, which was causing the initial VSI rebuild.
2. Adding functions for pre/post VSI rebuild functions that can be called
in both the reset all VFs case and reset individual VF case.
3. Adding VSI rebuild functions that are specific for the reset all VFs
case and adding functions that are specific for the reset individual
VF case.
4. Calling the pre-rebuild function, then the specific VSI rebuild
function based on the reset type, and then calling the post-rebuild
function to handle VF resets.
This patch series makes some assumptions about how VSI are handling by
FW during reset:
1. During a PFR or greater all VSI in FW will be cleared.
2. During a VFR/VFLR the VSI rebuild responsibility is in the hands of
the PF software.
3. There is code in the ice_reset_all_vfs() case to amortize operations
if possible. This was left intact.
4. PF software should not be replaying VSI based filters that were added
other than host configured, PF software configured, or the VF's
default/LAA MAC. This is the VF drivers job after it has been reset.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If register_netdev() fails, the driver will attempt to cleanup the
q_vectors and inadvertently trigger a kernel BUG due to a NULL pointer
dereference.
This occurs because cleaning up q_vectors attempts to call
netif_napi_del on napi_structs which were never initialized.
Resolve this by releasing the netdev in ice_cfg_netdev and setting
vsi->netdev to NULL. This ensures that after ice_cfg_netdev fails the
state is rewound to match as if ice_cfg_netdev was never called.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If ice_init_interrupt_scheme fails, ice_probe will jump to clearing up
the interrupts. This can lead to some static analysis tools such as the
compiler sanitizers complaining about double free problems.
Since ice_init_interrupt_scheme already unrolls internally on failure,
there is no need to call ice_clear_interrupt_scheme when it fails. Add
a new unroll label and use that instead.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are certain cases where the DDP load fails and the FW issues a
core reset. For these cases, wait for reset to complete before
proceeding with reset of the driver init.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In current implementation number of XDP Tx queues is the same as
the number of transmit queues, which is not always true. This
patch changes this number to match the number of receive queues.
XDP programs are running on Rx rings, so what we actually need to
provide is the XDP Tx ring per each Rx ring so that the whole XDP
ecosystem is functional, e.g. if the result of XDP prog is XDP_TX
then you have the need to access the XDP Tx ring.
Signed-off-by: Marta Plantykow <marta.a.plantykow@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When XDP Tx program is loaded and packets are sent from
interface, VSI statistics are not updated. This patch adds
packets sent on Tx XDP ring to VSI ring stats.
Signed-off-by: Marta Plantykow <marta.a.plantykow@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When XDP Tx rings are destroyed the number of XDP Tx queues
is not changing. This patch is changing this number to 0.
Signed-off-by: Marta Plantykow <marta.a.plantykow@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A race condition between FW and SW can occur between admin queue setup and
the first command sent. A link event may occur and FW attempts to notify a
non-existent queue. FW will set the critical error bit and disable the
queue. When this happens retry queue setup.
Signed-off-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently we are only including illegal_bytes and rx_crc_errors in the
PF netdev's rx_error counter. There are many more causes of Rx errors
that the device supports and reports via Ethtool. Accumulate all Rx
errors in the PF netdev's rx_error counter.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix the remaining signed vs unsigned issues, which appear
when compiling with -Werror=sign-compare.
Many of these are because there is an external interface that is passing
an int to us (which we can't change) but that we (rightfully) store
and compare against as an unsigned in our data structures.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix loop variables that are comparing or assigning signed against
unsigned values, mostly by declaring loop counters as unsigned.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was using rq_last_status where it should have been
using sq_last_status. Fix the string to be using the correct
error reporting variable.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Require the Dynamic Device Personalization (DDP) file to have the same
major version number and the same or older minor number than the firmware
version major and minor, respectively.
Check the OS and NVM package versions before downloading the package.
If the OS package version is not compatible with NVM then return an
appropriate error.
Split the 32-byte segment name into a 28-byte segment name and
a 4-byte Track-ID. Older packages will still work with this change
because no package has a name that will take up more than 28 bytes;
in this case the Track-ID will be 0.
Note that the driver will store the segment name as 32-bytes in the
ice_hw structure, in order to normalize the length of the various
package name strings that it uses.
Also add section ID and structure for the segment metadata section.
Signed-off-by: Victor Raj <victor.raj@intel.com>
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Rx MDD auto reset message was not being logged because logging occurred
after the VF reset and the VF MDD data was reinitialized.
Log the Rx MDD auto reset message before triggering the VF reset.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As per the specification, the driver needs to call set_mac_cfg
(opcode 0x0603) to be able to exercise jumbo frames. Call the
function during initialization and the post reset rebuild flow.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Enable accelerated Receive Flow Steering (aRFS). It is used to steer Rx
flows to a specific queue. This functionality is triggered by the network
stack through ndo_rx_flow_steer and requires Flow Director (ntuple on) to
function.
The fltr_info is used to add/remove/update flow rules in the HW, the
fltr_state is used to determine what to do with the filter with respect
to HW and/or SW, and the flow_id is used in co-ordination with the
network stack.
The work for aRFS is split into two paths: the ndo_rx_flow_steer
operation and the ice_service_task. The former is where the kernel hands
us an Rx SKB among other items to setup aRFS and the latter is where
the driver adds/updates/removes filter rules from HW and updates filter
state.
In the Rx path the following things can happen:
1. New aRFS entries are added to the hash table and the state is
set to ICE_ARFS_INACTIVE so the filter can be updated in HW
by the ice_service_task path.
2. aRFS entries have their Rx Queue updated if we receive a
pre-existing flow_id and the filter state is ICE_ARFS_ACTIVE.
The state is set to ICE_ARFS_INACTIVE so the filter can be
updated in HW by the ice_service_task path.
3. aRFS entries marked as ICE_ARFS_TODEL are deleted
In the ice_service_task path the following things can happen:
1. New aRFS entries marked as ICE_ARFS_INACTIVE are added or
updated in HW.
and their state is updated to ICE_ARFS_ACTIVE.
2. aRFS entries are deleted from HW and their state is updated
to ICE_ARFS_TODEL.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Madhu Chittim <madhu.chittim@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Following a reset, Flow Director filters are cleared from the hardware.
Rebuild the filters using the software structures containing the filter
rules.
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add functionality for ethtool --show-ntuple, allowing for filters to be
displayed when set functionality is added. Add statistics related to
Flow Director matches and status.
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Flow Director allows for redirection based on ntuple rules. Rules are
programmed using the ethtool set-ntuple interface. Supported actions are
redirect to queue and drop.
Setup the initial framework to process Flow Director filters. Create and
allocate resources to manage and program filters to the hardware. Filters
are processed via a sideband interface; a control VSI is created to manage
communication and process requests through the sideband. Upon allocation of
resources, update the hardware tables to accept perfect filters.
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The variable status cannot be zero due to a prior check of it; remove this
check.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The else conditional expression is always true due to the if conditional
expression; remove it and add a comment to make it obvious still.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In function ice_set_mac_address, we will remove old dev_addr before
adding the new MAC. In the removing and adding process of the MAC,
there is no need to return error if the check finds the to-be-removed
dev_addr does not exist in the MAC filter list or the to-be-added mac
already exists, keep going or return success accordingly.
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move filter functions to separate file.
Add functions that prepare suitable ice_fltr_info struct
depending on the filter type and add this struct to earlier created
list:
- ice_fltr_add_mac_to_list
- ice_fltr_add_vlan_to_list
- ice_fltr_add_eth_to_list
This functions are used in adding and removing filters.
Create wrappers for functions mentioned above that alloc list,
add suitable ice_fltr_info to it and call add or remove function.
- ice_fltr_prepare_mac
- ice_fltr_prepare_mac_and_broadcast
- ice_fltr_prepare_vlan
- ice_fltr_prepare_eth
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change min() macros to min_t() which has compare type specified and it
helps avoid precision loss.
In some cases there was precision loss during calls or assignments.
Some fields in structs were unnecessarily large and gave multiple
warnings.
There were also some minor type differences which are now fixed as well as
some cases where a simple cast was needed.
Callers were were passing data that is a u16 to
ice_sched_cfg_node_bw_alloc() but the function was truncating that to a u8.
Fix that by changing the function to take a u16.
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When printing the ice status or AQ error codes, instead of printing out the
numerical value, provide the description of the error code. This provides
more info about the issue than a number.
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As soon as the driver registers the PF netdev, userspace utilities
like NetworkManager try to bring up the associated interface. When
this happens, the driver may not have finished initializing fully,
resulting in a bunch of errors in the interface up flow.
The driver already has a mechanism to indicate if it's not up yet;
by setting the __ICE_DOWN bit in pf->state, but this bit gets
cleared too early in the current flow. So clear this bit only when
the driver is fully up. Also check for the same bit in the ice_open
flow, and return -EBUSY if the bit is set.
Also in ice_open, replace references of vsi->back with a local
variable.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When there's a Tx timeout for a queue which belongs to a PFC enabled TC,
then it's not because the queue is hung but because PFC is in action.
In PFC, peer sends a pause frame for a specified period of time when its
buffer threshold is exceeded (due to congestion). Netdev on the other
hand checks if ACK is received within a specified time for a TX packet, if
not, it'll invoke the tx_timeout routine.
Signed-off-by: Avinash JD <avinash.dayanand@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Create a boost TCAM entry for each tunnel port in order to get a tunnel
PTYPE. Update netdev feature flags and implement the appropriate logic to
get and set values for hardware offloads.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-----BEGIN PGP SIGNATURE-----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=deWu
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Revert sysfs "rescan" renames that broke apps (Kelsey Skunberg)
- Add more 32 GT/s link speed decoding and improve the implementation
(Yicong Yang)
Resource management:
- Add support for sizing programmable host bridge apertures and fix a
related alpha Nautilus regression (Ivan Kokshaysky)
Interrupts:
- Add boot interrupt quirk mechanism for Xeon chipsets and document
boot interrupts (Sean V Kelley)
PCIe native device hotplug:
- When possible, disable in-band presence detect and use PDS
(Alexandru Gagniuc)
- Add DMI table for devices that don't use in-band presence detection
but don't advertise that correctly (Stuart Hayes)
- Fix hang when powering slots up/down via sysfs (Lukas Wunner)
- Fix an MSI interrupt race (Stuart Hayes)
Virtualization:
- Add ACS quirks for Zhaoxin devices (Raymond Pang)
Error handling:
- Add Error Disconnect Recover (EDR) support so firmware can report
devices disconnected via DPC and we can try to recover (Kuppuswamy
Sathyanarayanan)
Peer-to-peer DMA:
- Add Intel Sky Lake-E Root Ports B, C, D to the whitelist (Andrew
Maier)
ASPM:
- Reduce severity of common clock config message (Chris Packham)
- Clear the correct bits when enabling L1 substates, so we don't go
to the wrong state (Yicong Yang)
Endpoint framework:
- Replace EPF linkup ops with notifier call chain and improve locking
(Kishon Vijay Abraham I)
- Fix concurrent memory allocation in OB address region (Kishon Vijay
Abraham I)
- Move PF function number assignment to EPC core to support multiple
function creation methods (Kishon Vijay Abraham I)
- Fix issue with clearing configfs "start" entry (Kunihiko Hayashi)
- Fix issue with endpoint MSI-X ignoring BAR Indicator and Table
Offset (Kishon Vijay Abraham I)
- Add support for testing DMA transfers (Kishon Vijay Abraham I)
- Add support for testing > 10 endpoint devices (Kishon Vijay Abraham I)
- Add support for tests to clear IRQ (Kishon Vijay Abraham I)
- Add common DT schema for endpoint controllers (Kishon Vijay Abraham I)
Amlogic Meson PCIe controller driver:
- Add DT bindings for AXG PCIe PHY, shared MIPI/PCIe analog PHY (Remi
Pommarel)
- Add Amlogic AXG PCIe PHY, AXG MIPI/PCIe analog PHY drivers (Remi
Pommarel)
Cadence PCIe controller driver:
- Add Root Complex/Endpoint DT schema for Cadence PCIe (Kishon Vijay
Abraham I)
Intel VMD host bridge driver:
- Add two VMD Device IDs that require bus restriction mode (Sushma
Kalakota)
Mobiveil PCIe controller driver:
- Refactor and modularize mobiveil driver (Hou Zhiqiang)
- Add support for Mobiveil GPEX Gen4 host (Hou Zhiqiang)
Microsoft Hyper-V host bridge driver:
- Add support for Hyper-V PCI protocol version 1.3 and
PCI_BUS_RELATIONS2 (Long Li)
- Refactor to prepare for virtual PCI on non-x86 architectures (Boqun
Feng)
- Fix memory leak in hv_pci_probe()'s error path (Dexuan Cui)
NVIDIA Tegra PCIe controller driver:
- Use pci_parse_request_of_pci_ranges() (Rob Herring)
- Add support for endpoint mode and related DT updates (Vidya Sagar)
- Reduce -EPROBE_DEFER error message log level (Thierry Reding)
Qualcomm PCIe controller driver:
- Restrict class fixup to specific Qualcomm devices (Bjorn Andersson)
Synopsys DesignWare PCIe controller driver:
- Refactor core initialization code for endpoint mode (Vidya Sagar)
- Fix endpoint MSI-X to use correct table address (Kishon Vijay
Abraham I)
TI DRA7xx PCIe controller driver:
- Fix MSI IRQ handling (Vignesh Raghavendra)
TI Keystone PCIe controller driver:
- Allow AM654 endpoint to raise MSI-X interrupt (Kishon Vijay Abraham I)
Miscellaneous:
- Quirk ASMedia XHCI USB to avoid "PME# from D0" defect (Kai-Heng
Feng)
- Use ioremap(), not phys_to_virt(), for platform ROM to fix video
ROM mapping with CONFIG_HIGHMEM (Mikel Rychliski)"
* tag 'pci-v5.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (96 commits)
misc: pci_endpoint_test: remove duplicate macro PCI_ENDPOINT_TEST_STATUS
PCI: tegra: Print -EPROBE_DEFER error message at debug level
misc: pci_endpoint_test: Use full pci-endpoint-test name in request_irq()
misc: pci_endpoint_test: Fix to support > 10 pci-endpoint-test devices
tools: PCI: Add 'e' to clear IRQ
misc: pci_endpoint_test: Add ioctl to clear IRQ
misc: pci_endpoint_test: Avoid using module parameter to determine irqtype
PCI: keystone: Allow AM654 PCIe Endpoint to raise MSI-X interrupt
PCI: dwc: Fix dw_pcie_ep_raise_msix_irq() to get correct MSI-X table address
PCI: endpoint: Fix ->set_msix() to take BIR and offset as arguments
misc: pci_endpoint_test: Add support to get DMA option from userspace
tools: PCI: Add 'd' command line option to support DMA
misc: pci_endpoint_test: Use streaming DMA APIs for buffer allocation
PCI: endpoint: functions/pci-epf-test: Print throughput information
PCI: endpoint: functions/pci-epf-test: Add DMA support to transfer data
PCI: pciehp: Fix MSI interrupt race
PCI: pciehp: Fix indefinite wait on sysfs requests
PCI: endpoint: Fix clearing start entry in configfs
PCI: tegra: Add support for PCIe endpoint mode in Tegra194
PCI: sysfs: Revert "rescan" file renames
...
The AER interfaces to clear error status registers were a confusing mess:
- pci_cleanup_aer_uncorrect_error_status() cleared non-fatal errors
from the Uncorrectable Error Status register.
- pci_aer_clear_fatal_status() cleared fatal errors from the
Uncorrectable Error Status register.
- pci_cleanup_aer_error_status_regs() cleared the Root Error Status
register (for Root Ports), the Uncorrectable Error Status register,
and the Correctable Error Status register.
Rename them to make them consistent:
From To
---------------------------------------- -------------------------------
pci_cleanup_aer_uncorrect_error_status() pci_aer_clear_nonfatal_status()
pci_aer_clear_fatal_status() pci_aer_clear_fatal_status()
pci_cleanup_aer_error_status_regs() pci_aer_clear_status()
Since pci_cleanup_aer_error_status_regs() (renamed to
pci_aer_clear_status()) is only used within drivers/pci/, move the
declaration from <linux/aer.h> to drivers/pci/pci.h.
[bhelgaas: commit log, add renames]
Link: https://lore.kernel.org/r/d1310a75dc3d28f7e8da4e99c45fbd3e60fe238e.1585000084.git.sathyanarayanan.kuppuswamy@linux.intel.com
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add a devlink region for exposing the device's Non Volatime Memory flash
contents.
Support the recently added .snapshot operation, enabling userspace to
request a snapshot of the NVM contents via DEVLINK_CMD_REGION_NEW.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Begin implementing support for the devlink interface with the ice
driver.
The pf structure is currently memory managed through devres, via
a devm_alloc. To mimic this behavior, after allocating the devlink
pointer, use devm_add_action to add a teardown action for releasing the
devlink memory on exit.
The ice hardware is a multi-function PCIe device. Thus, each physical
function will get its own devlink instance. This means that each
function will be treated independently, with its own parameters and
configuration. This is done because the ice driver loads a separate
instance for each function.
Due to this, the implementation does not enable devlink to manage
device-wide resources or configuration, as each physical function will
be treated independently. This is done for simplicity, as managing
a devlink instance across multiple driver instances would significantly
increase the complexity for minimal gain.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit ed5a3f664c ("ice: Removing hung_queue variable to use txqueue
function parameter") began utilizing the txqueue variable over the
hung_queue variable. hung_queue was an int where txqueue is an unsigned
int. Update the format specifiers to reflect the new type.
Fixes: ed5a3f664c ("ice: Removing hung_queue variable to use txqueue function parameter")
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the PF's mailbox receive queue is only 512 entries. This fine,
but considering that all VF's mailbox send queues funnel into the PF's
single mailbox receive queue, let's increase it to the maximum size. This
will help prevent any possible bottleneck/slowdown occurring from the PF's
mailbox receive queue being full.
Signed-off-by: Lukasz Czapnik <lukasz.czapnik@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, if there are bare-metal VFs passing traffic and the ice
driver is removed, there is a possibility of VFs triggering a Tx timeout
right before iavf_remove(). This is causing iavf_close() to not be
called because there is a check in the beginning of iavf_remove() that
bails out early if (adapter->state < IAVF_DOWN_PENDING). This makes it
so some resources do not get cleaned up. Specifically, free_irq()
is never called for data interrupts, which results in the following line
of code to trigger:
pci_disable_msix()
free_msi_irqs()
...
BUG_ON(irq_has_action(entry->irq + i));
...
To prevent the Tx timeout from occurring on the VF during driver unload
for ice and the iavf there are a few changes that are needed.
[1] Don't disable all active VF Tx/Rx queues prior to calling
pci_disable_sriov.
[2] Call ice_free_vfs() before disabling the service task.
[3] Disable VF resets when the ice driver is being unloaded by setting
the pf->state flag __ICE_VF_RESETS_DISABLED.
Changing [1] and [2] allow each VF driver's remove flow to successfully
send VIRTCHNL requests, which includes queue disable. This prevents
unexpected Tx timeouts because the PF driver is no longer forcefully
disabling queues.
Due to [1] and [2] there is a possibility that the PF driver will get a
VFLR or reset request over VIRTCHNL from a VF during PF driver unload.
Prevent that by doing [3].
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Replace the open-coded implementation for reading the PCIe DSN with
pci_get_dsn().
The pci_get_dsn() function will perform two pci_read_config_dword calls
to read the lower and upper config dwords. It bitwise ORs them into
a u64 value. Instead of using put_unaligned_le32 to convert the value to
LE32 format, just use the %016llX printf specifier. This will print the
u64 correct, putting the most significant byte of the value first. Since
pci_get_dsn() correctly orders the two dwords into a u64, this should
produce equivalent results in less code.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This product's name has changed; update the macro identifier accordingly.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add E823 device ids and convert conditional expressions to a more
appropriate switch statement.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for device id 0x159b.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There were several strings found without line feeds, fix
them by adding a line feed, as is typical. Without this
lotsofmessagescanbejumbledtogether.
This patch has known checkpatch warnings from long lines
for the NL_* messages, because checkpatch doesn't know
how to ignore them.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update the PF VFs MDD event message to rate limit once per second and
report the total number Rx|Tx event count. Add support to print pending
MDD events that occur during the rate limit. The use of net_ratelimit did
not allow for per VF Rx|Tx granularity.
Additional PF MDD log messages are guarded by netif_msg_[rx|tx]_err().
Since VF RX MDD events disable the queue, add ethtool private flag
mdd-auto-reset-vf to configure VF reset to re-enable the queue.
Disable anti-spoof detection interrupt to prevent spurious events
during a function reset.
To avoid race condition do not make PF MDD register reads conditional
on global MDD result.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit 0290bd291c ("netdev: pass the stuck queue to the timeout handler")
introduced a new argument to the function but missed adding the description
of the argument to the function header comment. Add it now.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
"fallthrough" comments are used in switch case statements to explicitly
indicate the code is intended to fall through to the following statement.
Different variants of "fallthough" are acceptable, e.g. "fall through",
"fallthrough", "Fall-through". The GCC compiler has an optional warning
(-Wimplicit-fallthrough[=n]) to warn when such a comment is not present;
the default version of which is enabled when compiling the Linux kernel.
There have been recent discussions in kernel mailing lists regarding
replacing non-standardized "fallthrough" comments with the pseudo-reserved
word 'fallthrough' which will be defined as __attribute__ ((fallthrough))
for versions of gcc that support it (i.e. gcc 7 and newer) or as a nop
for versions that do not. Replace "fallthrough" comments with fallthrough
reserved word.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fallthrough comments are used to explicitly indicate the code is intended
to flow from one case statement to the next in a switch statement rather
than break out of the switch statement. They are only needed when a case
has one or more statements to execute before falling through to the next
case, not when there is a list of cases for which the same statement(s)
should be executed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently we are not handling LAN overflow events. There can be cases
where LAN overflow events occur on VF queues, especially with Link Flow
Control (LFC) enabled on the controlling PF. In order to recover from
the LAN overflow event caused by a VF we need to determine if the queue
belongs to a VF and reset that VF accordingly.
The struct ice_aqc_event_lan_overflow returns a copy of the GLDCB_RTCTQ
register, which tells us what the queue index is in the global/device
space. The global queue index needs to first be converted to a PF space
queue index and then it can be used to find if a VF owns it.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
