When a VF is disabled, there is no way for it to recover until either
the PF driver is reloaded or SR-IOV is disabled and enabled. To correct
this, enable the VF after a successful reset.
Change-ID: I9e0788476c4d53d5407961b503febdfff2b8a7c6
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The VF disable code was just whanging on the reset bit without properly
cleaning up the VF, which would leave the VF in an indeterminate state
from which it could not recover. Fix this by notifying the VF and then
by calling the normal VF reset routine.
Change-ID: I862b9dfa919368773cbdc212b805b520db2f7430
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
MAC filters for VFs were being programmed with 0 for the VLAN value when
there was no VLAN assigned. This is incorrect and actually assigns the
VF to VLAN 0. Instead, we must use -1 to indicate that no VLAN is in
use. This change programs the filters correctly and gets rid of a bogus
error message when setting a port VLAN on an active VF.
Change-ID: Ica9a9906d768405377ff3308e27f7d0b5b2ea96e
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make the necessary updates to i40e_adminq_cmd.h.
Change-ID: Ib031c86cc6cab78e5aa44c64d8ce5474be8d7e42
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes some #ifdef's that should not be there. They
were stopping code that is needed from being compiled in.
With these #ifdef's removed, changes are needed in the driver
to fix some compile errors: adding missing parameters to
the definition of ndo_bridge_setlink and a ndo_dflt_brige_getlink call.
Change-ID: I5516614e1bc50b6bca0647cef971bc96161ba2de
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If user attempts to set a port VLAN on a VF that already has the same
port VLAN configured, the driver will go through a completely
unnecessary flurry of filter removals and filter adds. Just check for
this condition and return success instead of doing a bunch of busywork.
Change-ID: Ia1a9e83e6ed48b3f4658bc20dfc6af0cf525d54a
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver currently only maps TX and RX queues to a single MSI-X vector
per queue pair if there are exactly enough vectors for this.
Unfortunately, if we have too many vectors it will fail and allocate
queues to vectors in a suboptimal manner. Change the condition check to
allow for excess vectors. In this case, the extras just won't be used.
Change-ID: I23e1e2955c64739c86612db88a25583e6a7e0b17
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a prefetch for the next Tx descriptor to be used when we know
there are more coming.
Change-ID: Ibb9acab11d508eec2db7da795df74debc16eeacb
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The Flex10 device/function capability has been upgraded to include
information needed to support Flex-10 configurations. This patch adds new
fields to the i40e_hw_capabilities structure and updates
i40e_parse_discover_capabilities functions to extract them from the AQ
response. Naming convention has changed to use flex10 mode instead of
existing mfp_mode_1.
Change-ID: I305dd888866985a30293acb3fb14fa43ca6b79ea
Signed-off-by: Pawel Orlowski <pawel.orlowski@intel.com>
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since the driver can dynamically enable/disable FD ATR and SB features,
these stats help keep track of the current state and along with
fd_flush count provide a means to debug what could be going on
with the flow director filters. This will take away the need for
being verbose in our debug logs with respect to FD.
Change-ID: I29224f750fe6602391043655d18996570720377d
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e supports UDP tunnel headers up to 80 bytes in length, so
this adds a check to ensure that it doesn't try to offload
packets that exceed that.
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver will only configure as many queues as there are available
CPUs, up the maximum number of queues. However, it always configures
RSS as though it is using the maximum number of queues. This can cause
the device to drop a lot of RX traffic, as the packets get assigned to
nonfunctional queues.
Fix this by only configuring RSS with the number of active queues.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Down was requesting queue disables, but then exited immediately
without waiting for the queues to actually disable. This could
allow any function called after i40evf_down to run immediately,
including i40evf_up, and causes a memory leak.
Removing the whole reinit_locked function is the best way
to go about this, and allows for the driver to handle the
state changes by requesting reset from the periodic timer.
Also, add a couple WARN_ONs in slow path to help us recognize
if we re-introduce this issue or missed any cases.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In SPT hardware does not require this driver workaround.
Removed the conditional that caused K1 workaround execution on SPT.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Due to clocking changes in the Skylake platform, there was i219
data corruption. To work around this, HW team reported the need
to increase the minimum gap between the PHY FIFO read and write pointers.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In SPT/i219, there were CRC errors in speed 10/100 full duplex.
The solution given by the HW team is to increase the IPG from 8 to 0xC
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In i219, there is a hardware bug that prevented ULP entry.
A side effect of the original software fix for this was that EEE in
Sx couldn't be enabled.
This patch implements a modified flow that allows both ULP and EEE in Sx.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On power up, the MAC - PHY interface needs to be set to PCIe, even if
cable is disconnected. In ME systems, the ME handles this on exit from
Sx state. In non-ME, the driver handles it. Added a check for non-ME
system to the driver code that handles that.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
e1000e_disable_aspm called pci_disable_link_state_locked which requires
pci_bus_sem to be held, but is also called from places where this semaphore
was not previously acquired. This patch implements two flavors of
disable_aspm, one that acquires the lock, and the other (_locked) which
should be called when the semaphore is already acquired.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump version of igb to igb-5.2.18
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Disable IPv6 extension header processing as per hardware errata.
Also fix copyright date.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
One more missing piece of the puzzle. Add vlan dump support to switchdev
port's bridge_getlink. iproute2 "bridge vlan show" cmd already knows how
to show the vlans installed on the bridge and the device , but (until now)
no one implemented the port vlan part of the netlink PF_BRIDGE:RTM_GETLINK
msg. Before this patch, "bridge vlan show":
$ bridge -c vlan show
port vlan ids
sw1p1 30-34 << bridge side vlans
57
sw1p1 << device side vlans (missing)
sw1p2 57
sw1p2
sw1p3
sw1p4
br0 None
(When the port is bridged, the output repeats the vlan list for the vlans
on the bridge side of the port and the vlans on the device side of the
port. The listing above show no vlans for the device side even though they
are installed).
After this patch:
$ bridge -c vlan show
port vlan ids
sw1p1 30-34 << bridge side vlan
57
sw1p1 30-34 << device side vlans
57
3840 PVID
sw1p2 57
sw1p2 57
3840 PVID
sw1p3 3842 PVID
sw1p4 3843 PVID
br0 None
I re-used ndo_dflt_bridge_getlink to add vlan fill call-back func.
switchdev support adds an obj dump for VLAN objects, using the same
call-back scheme as FDB dump. Support included for both compressed and
un-compressed vlan dumps.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This howto made sense in the 1990s when users had to manually configure
ISA cards with jumpers or vendor utilities, but with the implementation
of PCI it became increasingly less and less relevant, to the point where
it has been well over a decade since I last updated it. And there is
no value in anyone else taking over updating it either.
However the references to it continue to spread as boiler plate text
from one Kconfig file into the next. We are not doing end users any
favours by pointing them at this old document, so lets kill it with
fire, once and for all, to hopefully stop any further spread.
No code is changed in this commit, just Kconfig help text.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reviewing the code I noticed that one of the commits added an if
statement followed by a for loop, but the if statement was missing the
braces around the loop. This change corrects the coding style error.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a VF issues an LPORT_STATE request to enable a port that is already
enabled, the PF will first disable the VF LPORT. Then it should
re-enable the VF again with the new requested settings. This ensures
that any switch rules are cleared by deleting the LPORT on the switch.
However, the flow is bugged because we actually check if the VF is
enabled at the end, and thus don't re-enable it. Fix the flow so that we
actually clear the enabled flags as part of our removal of the LPORT.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The reference to err_no was left around after a previous code refactor.
We never use the value, and it doesn't seem to be used in side a hidden
macro reference. Discovered via cppcheck.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The SYSTIME_CFG.Adjust Direction bit is actually supposed to indicate
that the adjustment is positive. Fix the code to align correctly with
hardware and documentation.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds the __attribute__((packed)) indicator to some structures
which are overlayed onto a TLV message. These structures must be packed
as small as possible in order to correctly align when copied into the
mailbox buffer. Without doing so, the receiving mailbox code incorrectly
parses the values and we get invalid message responses from the switch
manager software.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During initialization, the VF counts its rings by walking the TQDLOC
registers. This works only if the TQMAP/RQMAP registers are set to map
all of the out-of-bound rings back to the first one. This allows the VF
to cleanly detect when it has run out of queues. Update the PF code so
that it resets the empty TQMAP/RQMAP registers post-VFLR to prevent
innocent VF drivers from triggering malicious driver events.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, we don't notify the switch at all when the PF
administratively sets a new VLAN or MAC address. This causes the old
addresses to remain valid on the switch table. Since the PF is
overriding any configuration done directly by the VF, we choose to
simply re-create the LPORT for the VF. This does mean that all rules for
the VF will be dropped when we set something directly via the PF, but it
prevents some weird issues where the MAC/VLAN table retains some stale
configuration.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch cleans up the use of dma_get_required_mask and uses the
simpler dma_set_mask_and_coherent function instead of doing these as
separate steps.
I removed the dma_get_required_mask call because based on some minimal
testing it appears that either (a) we're not doing the right thing with
the call or (b) we don't need it anyways. If the value returned is
<48bits, we'll end up trying with 48 bits anyways. If it's over 48bits,
fm10k can't support that anyways, and we should try 48bits. If 48bits
fails, we'll fallback to 32bits. This cleans up some very funky code.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Also use %d for error values, since printing in hexadecimal is probably
not helpful.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
l2_accel was checked for NULL at the top of fm10k_dfwd_del_station, and
we return if it is not defined. Due to this, we already know it can't be
null here so a separate check is meaningless. Discovered via cppcheck.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The value will never be negative, and we use the %u print format. Thus,
use unsigned int for the loop counter. Issue found using cppcheck.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This prevents a memory leak in fm10k_set_ringparams. The leak occurs
because we go down, change ring parameters, and then come up. However,
fm10k_down on its own is not clearing the Rx rings. Since fm10k_up
assumes the rings are clean we basically drop the buffers and leak a
bunch of memory. Eventually we hit dirty page faults and reboot the
system. This issue does not occur elsewhere because other flows that
involve fm10k_down go through fm10k_close which immediately called
fm10k_free_all_rx_resources which properly cleans the rings.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch resolves a bug in the ts_tx_enqueue code responsible for a
NULL pointer dereference and invalid access of the skb list. We
incorrectly freed the actual skb we found instead of our copy. Thus the
skb queue is essentially invalidated. Resolve this by freeing our clone
in the cases where we did not add it to the queue. This also avoids the
skb memory leak caused by failure to free the clone.
[ 589.719320] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 589.722344] IP: [<ffffffffa0310e60>] fm10k_ts_tx_subtask+0xb0/0x160 [fm10k]
[ 589.723796] PGD 0
[ 589.725228] Oops: 0000 [#1] SMP
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch simplifies the code flow for setting the IN_PROGRESS bit of
the shinfo for an skb we will be timestamping.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change fixes an issue with adding an invalid multicast address
using the iproute2 tool (ip maddr add <MADDR> dev <dev>). The iproute2
tool and the kernel do not validate or filter the multicast addresses
when adding them to the multicast list. Thus, when synchronizing this
list with an invalid entry, the action will be aborted with an error
since the fm10k driver currently validates the list. Consequently,
multicast entries beyond the invalid one will not be processed and
communicated with the switch via the mailbox. This change makes it so
that invalid addresses will simply be skipped and allows synchronizing
the full list to proceed.
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change folds the fm10k_pull_tail call into fm10k_add_rx_frag. The
advantage to doing this is that the fragment doesn't have to be modified
after it is added to the skb.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When programming the start of a periodic output, the code wrongly places
the seconds value into the "low" register and the nanoseconds into the
"high" register. Even though this is backwards, it slipped through my
testing, because the re-arming code in the interrupt service routine is
correct, and the signal does appear starting with the second edge.
This patch fixes the issue by programming the registers correctly.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects a bug in ixgbe_setup_ixfi_x550em where we were
reading and modifying IXGBE_KRM_LINK_CTRL_1 but forgot to write the
results back.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Even though X550 may later clear this value for certain devices
set it initially to support copper.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We need to call the set_lan_id before accessing I2C and this wasn't
being done so this patch corrects that. Likewise we do the same for
QSFP just to be consistent.
In the X550 case this is even more important as with out it the mux
is not controlled properly.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds ixgbe_check_link_t_X550em for checking copper PHY
link. We check that both the MAC and external PHY have link. This
is to avoid a false link up between the internal and external PHY
when the external PHY doesn't have link.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for another 10baseT X550 device.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A subset of the X550 function pointers didn't have default methods. This
didn't cause any issue with previous X550 devices as they were all
redefined. However future devices will need these default values.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reviewing the X550 copper init flow with the Si team resulted in a
new simplified flow. We no longer wait for the PHY FW initialization
complete bit to be set as this bit is only set once by the PHY at power
on and then cleared on the first read. So only the first instance of
running SW (or possibly MAC FW) needs to initialize the PHY.
The PHY initialization has been simplified and now only requires that
the PHY FW be un-stalled
low-power mode or enabled the transceiver
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This check was missed in when this new MAC type was added. Since
these counts can be incremented for X550 we need to clear them.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
