Fix the condition which verifies that doorbell address is inside the
doorbell bar by checking that the end of the address is within range
as well.
Signed-off-by: Denis Bolotin <dbolotin@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DB_REC_DRY_RUN (running doorbell recovery without sending doorbells) is
never used. DB_REC_ONCE (send a single doorbell from the doorbell recovery)
is not needed anymore because by running the periodic handler we make sure
we check the overflow status later instead.
This patch is needed because in the next patches, the only doorbell
recovery type being used is DB_REC_REAL_DEAL, and the fixes are much
cleaner without this enum.
Signed-off-by: Denis Bolotin <dbolotin@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch introduces a new Multi-Function bit for cases where firmware
shouldn't perform the insertion of vlan-0 tag. The new bit is defined to
abstract the implementation from the actual MF mode.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Read port count from the shared memory instead of driver deriving this
value. This change simplifies the driver implementation and also avoids
any dependencies for finding the port-count.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the detection and handling of a parity error ("process kill
event"), including the update of the protocol drivers, and the prevention
of any HW access that will lead to device access towards the host while
recovery is in progress.
It also provides the means for the protocol drivers to trigger a recovery
process on their decision.
Signed-off-by: Tomer Tayar <tomer.tayar@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initiating final cleanup after an ungraceful driver unload can lead to bad
PCI accesses towards the host.
This patch revises the load sequence so final cleanup is sent while the
internal master enable is cleared, to prevent the host accesses, and clears
the internal error indications just before enabling the internal master
enable.
Signed-off-by: Tomer Tayar <tomer.tayar@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a spelling mistake in a DP_NOTICE message, fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of an attention from the doorbell queue block, analyze the HW
indications. In case of a doorbell overflow, execute a doorbell recovery.
Since there can be spurious indications (race conditions between multiple PFs),
schedule a periodic task for checking whether a doorbell overflow may have been
missed. After a set time with no indications, terminate the periodic task.
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the database used to register doorbelling entities, and APIs for adding
and deleting entries, and logic for traversing the database and doorbelling
once on behalf of all entities.
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The getter callers doesn't know the valid Physical Queues (PQ) values.
This patch makes sure that a valid PQ will always be returned.
The patch consists of 3 fixes:
- When qed_init_qm_get_idx_from_flags() receives a disabled flag, it
returned PQ 0, which can potentially be another function's pq. Verify
that flag is enabled, otherwise return default start_pq.
- When qed_init_qm_get_idx_from_flags() receives an unknown flag, it
returned NULL and could lead to a segmentation fault. Return default
start_pq instead.
- A modulo operation was added to MCOS/VFS PQ getters to make sure the
PQ returned is in range of the required flag.
Fixes: b5a9ee7cf3 ("qed: Revise QM cofiguration")
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the condition which verifies that only one flag is set. The API
bitmap_weight() should receive size in bits instead of bytes.
Fixes: b5a9ee7cf3 ("qed: Revise QM cofiguration")
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Certain flows need to access the rdma-info structure, for example dcbx
update flows. In some cases there can be a race between the allocation or
deallocation of the structure which was done in roce start / roce stop and
an asynchrounous dcbx event that tries to access the structure.
For this reason, we move the allocation of the rdma_info structure to be
similar to the iscsi/fcoe info structures which are allocated during device
setup.
We add a new field of "active" to the struct to define whether roce has
already been started or not, and this is checked instead of whether the
pointer to the info structure.
Fixes: 51ff17251c ("qed: Add support for RoCE hw init")
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add driver support for configuring/reading the 20G link speed.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Version bump conflict in batman-adv, take what's in net-next.
iavf conflict, adjustment of netdev_ops in net-next conflicting
with poll controller method removal in net.
Signed-off-by: David S. Miller <davem@davemloft.net>
In multi-function mode, driver receives the stag value (outer vlan)
for a PF from management FW (MFW). If the stag value is negotiated prior to
the driver load, then the stag is not notified to the driver and hence
driver will have the invalid stag value.
The fix is to request the MFW for STAG value during the driver load time.
Fixes: cac6f691 ("qed: Add support for Unified Fabric Port")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new qed firmware with fixes and support for new features.
Fixes:
- Fix a rare case of device crash with iWARP, iSCSI or FCoE offload.
- Fix GRE tunneled traffic when iWARP offload is enabled.
- Fix RoCE failure in ib_send_bw when using inline data.
- Fix latency optimization flow for inline WQEs.
- BigBear 100G fix
RDMA:
- Reduce task context size.
- Application page sizes above 2GB support.
- Performance improvements.
ETH:
- Tenant DCB support.
- Replace RSS indirection table update interface.
Misc:
- Debug Tools changes.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case, I replaced the code comments with
a proper "fall through" annotation, which is what GCC is expecting
to find.
Addresses-Coverity-ID: 114809 ("Missing break in switch")
Addresses-Coverity-ID: 114810 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RoCE qps use a pair of physical queues (pq) received from the Queue Manager
(QM) - an offload queue (OFLD) and a low latency queue (LLT). The QM block
creates a pq for each TC, and allows RoCE qps to ask for a pq with a
specific TC. As a result, qps with different VLAN priorities can be mapped
to different TCs, and employ features such as PFC and ETS.
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Distinguish not set offload_tc from offload_tc 0 and add getters and
setters.
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/ethernet/qlogic/qed/qed_cxt.c:1534:6: warning: symbol 'qed_cm_init_pf' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:233:4: warning: symbol 'qed_init_qm_get_num_tcs' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:238:5: warning: symbol 'qed_init_qm_get_num_vfs' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:246:5: warning: symbol 'qed_init_qm_get_num_pf_rls' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:264:5: warning: symbol 'qed_init_qm_get_num_vports' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:276:5: warning: symbol 'qed_init_qm_get_num_pqs' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_mcp.c:573:5: warning: symbol 'qed_mcp_nvm_wr_cmd' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_mcp.c:3012:1: warning: symbol '__qed_mcp_resc_lock' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dcbx.c:870:6: warning: symbol 'qed_dcbx_aen' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_debug.c:7841:5: warning: symbol 'qed_dbg_nvm_image_length' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_debug.c:7857:5: warning: symbol 'qed_dbg_nvm_image' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_sriov.c:675:6: warning: symbol '_qed_iov_pf_sanity_check' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_sriov.c:690:6: warning: symbol 'qed_iov_pf_sanity_check' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_sriov.c:3982:6: warning: symbol 'qed_iov_pf_get_pending_events' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_vf.c:172:5: warning: symbol '_qed_vf_pf_release' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_rdma.c:137:5: warning: symbol 'qed_rdma_get_sb_id' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_rdma.c:709:5: warning: symbol 'qed_rdma_stop' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_ll2.c:161:6: warning: symbol 'qed_ll2b_complete_rx_packet' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_roce.c:160:6: warning: symbol 'qed_roce_free_cid_pair' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:380:12: warning: symbol 'iwarp_state_names' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:946:1: warning: symbol 'qed_iwarp_parse_private_data' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:971:1: warning: symbol 'qed_iwarp_mpa_reply_arrived' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:2504:1: warning: symbol 'qed_iwarp_ll2_slowpath' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:2806:6: warning: symbol 'qed_iwarp_qp_in_error' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:2827:6: warning: symbol 'qed_iwarp_exception_received' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:2958:1: warning: symbol 'qed_iwarp_connect_complete' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iscsi.c:876:6: warning: symbol 'qed_iscsi_free_connection' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Denis Bolotin <Denis.Bolotin@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are no in-tree callers of qed_get_cm_pq_idx_rl since it be there,
so it can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, driver sets the eswitch mode incorrectly as VEB (virtual
Ethernet bridging).
Need to set VEB eswitch mode only when sriov is enabled, and it should be
to set NONE by default. The patch incorporates this change.
Fixes: 0fefbfbaa ("qed*: Management firmware - notifications and defaults")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This FW contains several fixes and features.
RDMA
- Several modifications and fixes for Memory Windows
- drop vlan and tcp timestamp from mss calculation in driver for
this FW
- Fix SQ completion flow when local ack timeout is infinite
- Modifications in t10dif support
ETH
- Fix aRFS for tunneled traffic without inner IP.
- Fix chip configuration which may fail under heavy traffic conditions.
- Support receiving any-VNI in VXLAN and GENEVE RX classification.
iSCSI / FcoE
- Fix iSCSI recovery flow
- Drop vlan and tcp timestamp from mss calc for fw 8.37.2.0
Misc
- Several registers (split registers) won't read correctly with
ethtool -d
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Manish Rangankar <manish.rangankar@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove and coalesce formats when there is an unnecessary
character after a logging newline. These extra characters
cause logging defects.
Miscellanea:
o Coalesce formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds driver changes for supporting the Unified Fabric Port
(UFP). This is a new paritioning mode wherein MFW provides the set of
parameters to be used by the device such as traffic class, outer-vlan
tag value, priority type etc. Drivers receives this info via notifications
from mfw and configures the hardware accordingly.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds support for new Multi function mode wherein the traffic
classification is done based on the 802.1ad tagging and the outer vlan tag
provided by the management firmware.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
`mf_mode' field indicates the multi-partitioning mode the device is
configured to. This method doesn't scale very well, adding a new MF mode
requires going over all the existing conditions, and deciding whether those
are needed for the new mode or not.
The patch defines a set of bit-fields for modes which are derived according
to the mode info shared by the MFW and all the configuration would be made
according to those. To add a new mode, there would be a single place where
we'll need to go and choose which bits apply and which don't.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for populating the flash image attributes.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This FW contains several fixes and features
RDMA Features
- SRQ support
- XRC support
- Memory window support
- RDMA low latency queue support
- RDMA bonding support
RDMA bug fixes
- RDMA remote invalidate during retransmit fix
- iWARP MPA connect interop issue with RTR fix
- iWARP Legacy DPM support
- Fix MPA reject flow
- iWARP error handling
- RQ WQE validation checks
MISC
- Fix some HSI types endianity
- New Restriction: vlan insertion in core_tx_bd_data can't be set
for LB packets
ETH
- HW QoS offload support
- Fix vlan, dcb and sriov flow of VF sending a packet with
inband VLAN tag instead of default VLAN
- Allow GRE version 1 offloads in RX flow
- Allow VXLAN steering
iSCSI / FcoE
- Fix bd availability checking flow
- Support 256th sge proerly in iscsi/fcoe retransmit
- Performance improvement
- Fix handle iSCSI command arrival with AHS and with immediate
- Fix ipv6 traffic class configuration
DEBUG
- Update debug utilities
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Acked-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Assign true or false to boolean variables instead of an integer value.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Sudarsana Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Advance the qed* drivers to use firmware 8.33.1.0:
Modify core driver (qed) to utilize the new FW and initialize the device
with it. This is the lion's share of the patch, and includes changes to FW
interface files, device initialization flows, FW interaction flows, and
debug collection flows.
Modify Ethernet driver (qede) to make use of new FW in fastpath.
Modify RoCE/iWARP driver (qedr) to make use of new FW in fastpath.
Modify FCoE driver (qedf) to make use of new FW in fastpath.
Modify iSCSI driver (qedi) to make use of new FW in fastpath.
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Bason <Yuval.Bason@cavium.com>
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Manish Chopra <Manish.Chopra@cavium.com>
Signed-off-by: Chad Dupuis <Chad.Dupuis@cavium.com>
Signed-off-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch refactors and reorders the FW API files in preparation of
upgrading the code to support new FW.
- Make use of the BIT macro in appropriate places.
- Whitespace changes to align values and code blocks.
- Comments are updated (spelling mistakes, removed if not clear).
- Group together code blocks which are related or deal with similar
matters.
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add the ethtool support to set RX/Tx coalesce
value to the VF associated Rx/Tx queues.
Signed-off-by: Rahul Verma <Rahul.Verma@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds required driver support for reading/configuring the
Energy Efficient Ethernet (EEE) parameters.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iWARP has different physical queue requirements than RoCE
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the passive side connect.
It addresses pre-allocating resources, creating a connection
element upon valid SYN packet received. Calling upper layer and
implementation of the accept/reject calls.
Error handling is not part of this patch.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds iWARP support for flows that have common code
between RoCE and iWARP, such as initialization, teardown and
qp setup verbs: create, destroy, modify, query.
It introduces the iWARP specific files qed_iwarp.[ch] and
iwarp_common.h
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iWARP personality introduced the need for differentiating in several
places in the code whether we are RoCE, iWARP or either. This
leads to introducing new macros for querying the personality.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch places common iWARP / RoCE code in qed_rdma
and roce specific code in qed_roce
There is one new function ( qed_roce_setup ) added, the rest
of the patch removes content from the files and removes some
static definitions.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iWARP would require the chains to allocate/free their PBL memory
independently, so add the infrastructure to provide it externally.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VFs are currently not mapping their doorbell bar, instead relying
on the small doorbell window they have in their limited regview bar.
In order to increase the number of possible Tx connections [queues]
employeed by VF past 16, we need to start using the doorbell bar if
one such is exposed - VF would communicate this fact to PF which would
return the size-bar internally configured into chip, according to
which the VF would decide whether to actually utilize the doorbell
bar.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First step in allowing a single PF/VF to open multiple queues on
the same queue zone is to add per-hwfn database of queue-cids
as a two-dimensional array where entry would be according to
[queue zone][internal index].
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Share several new tidbits with qedf:
- wwpn & wwnn
- Absolute pf-id [this one is actually meant for qedi as well]
- Number of available CQs
While we're at it, now that qedf will be aware of the available CQs
we can add some validation on the inputs it provides.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we're resetting the IGU CAM each time we initialize the PF
device, there's no need to reset the VF SBs again when initializing
IOV.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IGU CAM contains an assocaition between hardware SBs
and interrupt lines, and it can be dynamically configured
to allow more interrupts in one entity over another, specifically
for Re-distibution of SBs between a PF and its child VFs.
While we don't yet use this functionality, there are other
clients that do and as such its possible the information
passed from management firmware during initialization in
regard to the possible number of SBs doesn't accurately reflect
the current HW configuration.
The following changes are going to apply to the driver init sequence:
a. PF is going to re-configure all entries belonging to itself and
its child VFs in IGU CAM based on the management firmware info
regarding the number of SBs that are supposed to exist there.
b. PF is going to stop using the SB resource [management firmware
provided information] for anything but the initialization.
Instead, it would use the live-time counters it maintains for
the numbers.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already have an API struct that contains interrupt-related
numbers. Use it to encapsulate all information relating to the
status of SBs as (used|free).
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
