Currently we save host state like user-visible host MSRs, and do some
initial guest register setup for MSR_TSC_AUX and MSR_AMD64_TSC_RATIO
in svm_vcpu_load(). Defer this until just before we enter the guest by
moving the handling to kvm_x86_ops.prepare_guest_switch() similarly to
how it is done for the VMX implementation.
Additionally, since handling of saving/restoring host user MSRs is the
same both with/without SEV-ES enabled, move that handling to common
code.
Suggested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Michael Roth <michael.roth@amd.com>
Message-Id: <20210202190126.2185715-4-michael.roth@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now that the set of host user MSRs that need to be individually
saved/restored are the same with/without SEV-ES, we can drop the
.sev_es_restored flag and just iterate through the list unconditionally
for both cases. A subsequent patch can then move these loops to a
common path.
Signed-off-by: Michael Roth <michael.roth@amd.com>
Message-Id: <20210202190126.2185715-3-michael.roth@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Using a guest workload which simply issues 'hlt' in a tight loop to
generate VMEXITs, it was observed (on a recent EPYC processor) that a
significant amount of the VMEXIT overhead measured on the host was the
result of MSR reads/writes in svm_vcpu_load/svm_vcpu_put according to
perf:
67.49%--kvm_arch_vcpu_ioctl_run
|
|--23.13%--vcpu_put
| kvm_arch_vcpu_put
| |
| |--21.31%--native_write_msr
| |
| --1.27%--svm_set_cr4
|
|--16.11%--vcpu_load
| |
| --15.58%--kvm_arch_vcpu_load
| |
| |--13.97%--svm_set_cr4
| | |
| | |--12.64%--native_read_msr
Most of these MSRs relate to 'syscall'/'sysenter' and segment bases, and
can be saved/restored using 'vmsave'/'vmload' instructions rather than
explicit MSR reads/writes. In doing so there is a significant reduction
in the svm_vcpu_load/svm_vcpu_put overhead measured for the above
workload:
50.92%--kvm_arch_vcpu_ioctl_run
|
|--19.28%--disable_nmi_singlestep
|
|--13.68%--vcpu_load
| kvm_arch_vcpu_load
| |
| |--9.19%--svm_set_cr4
| | |
| | --6.44%--native_read_msr
| |
| --3.55%--native_write_msr
|
|--6.05%--kvm_inject_nmi
|--2.80%--kvm_sev_es_mmio_read
|--2.19%--vcpu_put
| |
| --1.25%--kvm_arch_vcpu_put
| native_write_msr
Quantifying this further, if we look at the raw cycle counts for a
normal iteration of the above workload (according to 'rdtscp'),
kvm_arch_vcpu_ioctl_run() takes ~4600 cycles from start to finish with
the current behavior. Using 'vmsave'/'vmload', this is reduced to
~2800 cycles, a savings of 39%.
While this approach doesn't seem to manifest in any noticeable
improvement for more realistic workloads like UnixBench, netperf, and
kernel builds, likely due to their exit paths generally involving IO
with comparatively high latencies, it does improve overall overhead
of KVM_RUN significantly, which may still be noticeable for certain
situations. It also simplifies some aspects of the code.
With this change, explicit save/restore is no longer needed for the
following host MSRs, since they are documented[1] as being part of the
VMCB State Save Area:
MSR_STAR, MSR_LSTAR, MSR_CSTAR,
MSR_SYSCALL_MASK, MSR_KERNEL_GS_BASE,
MSR_IA32_SYSENTER_CS,
MSR_IA32_SYSENTER_ESP,
MSR_IA32_SYSENTER_EIP,
MSR_FS_BASE, MSR_GS_BASE
and only the following MSR needs individual handling in
svm_vcpu_put/svm_vcpu_load:
MSR_TSC_AUX
We could drop the host_save_user_msrs array/loop and instead handle
MSR read/write of MSR_TSC_AUX directly, but we leave that for now as
a potential follow-up.
Since 'vmsave'/'vmload' also handles the LDTR and FS/GS segment
registers (and associated hidden state)[2], some of the code
previously used to handle this is no longer needed, so we drop it
as well.
The first public release of the SVM spec[3] also documents the same
handling for the host state in question, so we make these changes
unconditionally.
Also worth noting is that we 'vmsave' to the same page that is
subsequently used by 'vmrun' to record some host additional state. This
is okay, since, in accordance with the spec[2], the additional state
written to the page by 'vmrun' does not overwrite any fields written by
'vmsave'. This has also been confirmed through testing (for the above
CPU, at least).
[1] AMD64 Architecture Programmer's Manual, Rev 3.33, Volume 2, Appendix B, Table B-2
[2] AMD64 Architecture Programmer's Manual, Rev 3.31, Volume 3, Chapter 4, VMSAVE/VMLOAD
[3] Secure Virtual Machine Architecture Reference Manual, Rev 3.01
Suggested-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Michael Roth <michael.roth@amd.com>
Message-Id: <20210202190126.2185715-2-michael.roth@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If not in long mode, the low bits of CR3 are reserved but not enforced to
be zero, so remove those checks. If in long mode, however, the MBZ bits
extend down to the highest physical address bit of the guest, excluding
the encryption bit.
Make the checks consistent with the above, and match them between
nested_vmcb_checks and KVM_SET_SREGS.
Cc: stable@vger.kernel.org
Fixes: 761e416934 ("KVM: nSVM: Check that MBZ bits in CR3 and CR4 are not set on vmrun of nested guests")
Fixes: a780a3ea62 ("KVM: X86: Fix reserved bits check for MOV to CR3")
Reviewed-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Typically under KVM, an AP is booted using the INIT-SIPI-SIPI sequence,
where the guest vCPU register state is updated and then the vCPU is VMRUN
to begin execution of the AP. For an SEV-ES guest, this won't work because
the guest register state is encrypted.
Following the GHCB specification, the hypervisor must not alter the guest
register state, so KVM must track an AP/vCPU boot. Should the guest want
to park the AP, it must use the AP Reset Hold exit event in place of, for
example, a HLT loop.
First AP boot (first INIT-SIPI-SIPI sequence):
Execute the AP (vCPU) as it was initialized and measured by the SEV-ES
support. It is up to the guest to transfer control of the AP to the
proper location.
Subsequent AP boot:
KVM will expect to receive an AP Reset Hold exit event indicating that
the vCPU is being parked and will require an INIT-SIPI-SIPI sequence to
awaken it. When the AP Reset Hold exit event is received, KVM will place
the vCPU into a simulated HLT mode. Upon receiving the INIT-SIPI-SIPI
sequence, KVM will make the vCPU runnable. It is again up to the guest
to then transfer control of the AP to the proper location.
To differentiate between an actual HLT and an AP Reset Hold, a new MP
state is introduced, KVM_MP_STATE_AP_RESET_HOLD, which the vCPU is
placed in upon receiving the AP Reset Hold exit event. Additionally, to
communicate the AP Reset Hold exit event up to userspace (if needed), a
new exit reason is introduced, KVM_EXIT_AP_RESET_HOLD.
A new x86 ops function is introduced, vcpu_deliver_sipi_vector, in order
to accomplish AP booting. For VMX, vcpu_deliver_sipi_vector is set to the
original SIPI delivery function, kvm_vcpu_deliver_sipi_vector(). SVM adds
a new function that, for non SEV-ES guests, invokes the original SIPI
delivery function, kvm_vcpu_deliver_sipi_vector(), but for SEV-ES guests,
implements the logic above.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Message-Id: <e8fbebe8eb161ceaabdad7c01a5859a78b424d5e.1609791600.git.thomas.lendacky@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The GHCB specification requires the hypervisor to save the address of an
AP Jump Table so that, for example, vCPUs that have been parked by UEFI
can be started by the OS. Provide support for the AP Jump Table set/get
exit code.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The run sequence is different for an SEV-ES guest compared to a legacy or
even an SEV guest. The guest vCPU register state of an SEV-ES guest will
be restored on VMRUN and saved on VMEXIT. There is no need to restore the
guest registers directly and through VMLOAD before VMRUN and no need to
save the guest registers directly and through VMSAVE on VMEXIT.
Update the svm_vcpu_run() function to skip register state saving and
restoring and provide an alternative function for running an SEV-ES guest
in vmenter.S
Additionally, certain host state is restored across an SEV-ES VMRUN. As
a result certain register states are not required to be restored upon
VMEXIT (e.g. FS, GS, etc.), so only do that if the guest is not an SEV-ES
guest.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Message-Id: <fb1c66d32f2194e171b95fc1a8affd6d326e10c1.1607620209.git.thomas.lendacky@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
An SEV-ES vCPU requires additional VMCB vCPU load/put requirements. SEV-ES
hardware will restore certain registers on VMEXIT, but not save them on
VMRUN (see Table B-3 and Table B-4 of the AMD64 APM Volume 2), so make the
following changes:
General vCPU load changes:
- During vCPU loading, perform a VMSAVE to the per-CPU SVM save area and
save the current values of XCR0, XSS and PKRU to the per-CPU SVM save
area as these registers will be restored on VMEXIT.
General vCPU put changes:
- Do not attempt to restore registers that SEV-ES hardware has already
restored on VMEXIT.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Message-Id: <019390e9cb5e93cd73014fa5a040c17d42588733.1607620209.git.thomas.lendacky@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
An SEV-ES vCPU requires additional VMCB initialization requirements for
vCPU creation and vCPU load/put requirements. This includes:
General VMCB initialization changes:
- Set a VMCB control bit to enable SEV-ES support on the vCPU.
- Set the VMCB encrypted VM save area address.
- CRx registers are part of the encrypted register state and cannot be
updated. Remove the CRx register read and write intercepts and replace
them with CRx register write traps to track the CRx register values.
- Certain MSR values are part of the encrypted register state and cannot
be updated. Remove certain MSR intercepts (EFER, CR_PAT, etc.).
- Remove the #GP intercept (no support for "enable_vmware_backdoor").
- Remove the XSETBV intercept since the hypervisor cannot modify XCR0.
General vCPU creation changes:
- Set the initial GHCB gpa value as per the GHCB specification.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Message-Id: <3a8aef366416eddd5556dfa3fdc212aafa1ad0a2.1607620209.git.thomas.lendacky@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The SVM host save area is used to restore some host state on VMEXIT of an
SEV-ES guest. After allocating the save area, clear it and add the
encryption mask to the SVM host save area physical address that is
programmed into the VM_HSAVE_PA MSR.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Message-Id: <b77aa28af6d7f1a0cb545959e08d6dc75e0c3cba.1607620209.git.thomas.lendacky@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
For an SEV-ES guest, string-based port IO is performed to a shared
(un-encrypted) page so that both the hypervisor and guest can read or
write to it and each see the contents.
For string-based port IO operations, invoke SEV-ES specific routines that
can complete the operation using common KVM port IO support.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Message-Id: <9d61daf0ffda496703717218f415cdc8fd487100.1607620209.git.thomas.lendacky@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
For an SEV-ES guest, MMIO is performed to a shared (un-encrypted) page
so that both the hypervisor and guest can read or write to it and each
see the contents.
The GHCB specification provides software-defined VMGEXIT exit codes to
indicate a request for an MMIO read or an MMIO write. Add support to
recognize the MMIO requests and invoke SEV-ES specific routines that
can complete the MMIO operation. These routines use common KVM support
to complete the MMIO operation.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Message-Id: <af8de55127d5bcc3253d9b6084a0144c12307d4d.1607620209.git.thomas.lendacky@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The GHCB specification defines a GHCB MSR protocol using the lower
12-bits of the GHCB MSR (in the hypervisor this corresponds to the
GHCB GPA field in the VMCB).
Function 0x100 is a request for termination of the guest. The guest has
encountered some situation for which it has requested to be terminated.
The GHCB MSR value contains the reason for the request.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Message-Id: <f3a1f7850c75b6ea4101e15bbb4a3af1a203f1dc.1607620209.git.thomas.lendacky@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The GHCB specification defines a GHCB MSR protocol using the lower
12-bits of the GHCB MSR (in the hypervisor this corresponds to the
GHCB GPA field in the VMCB).
Function 0x004 is a request for CPUID information. Only a single CPUID
result register can be sent per invocation, so the protocol defines the
register that is requested. The GHCB MSR value is set to the CPUID
register value as per the specification via the VMCB GHCB GPA field.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Message-Id: <fd7ee347d3936e484c06e9001e340bf6387092cd.1607620209.git.thomas.lendacky@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The GHCB specification defines a GHCB MSR protocol using the lower
12-bits of the GHCB MSR (in the hypervisor this corresponds to the
GHCB GPA field in the VMCB).
Function 0x002 is a request to set the GHCB MSR value to the SEV INFO as
per the specification via the VMCB GHCB GPA field.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Message-Id: <c23c163a505290a0d1b9efc4659b838c8c902cbc.1607620209.git.thomas.lendacky@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
SEV-ES adds a new VMEXIT reason code, VMGEXIT. Initial support for a
VMGEXIT includes mapping the GHCB based on the guest GPA, which is
obtained from a new VMCB field, and then validating the required inputs
for the VMGEXIT exit reason.
Since many of the VMGEXIT exit reasons correspond to existing VMEXIT
reasons, the information from the GHCB is copied into the VMCB control
exit code areas and KVM register areas. The standard exit handlers are
invoked, similar to standard VMEXIT processing. Before restarting the
vCPU, the GHCB is updated with any registers that have been updated by
the hypervisor.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Message-Id: <c6a4ed4294a369bd75c44d03bd7ce0f0c3840e50.1607620209.git.thomas.lendacky@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since the guest register state of an SEV-ES guest is encrypted, debugging
is not supported. Update the code to prevent guest debugging when the
guest has protected state.
Additionally, an SEV-ES guest must only and always intercept DR7 reads and
writes. Update set_dr_intercepts() and clr_dr_intercepts() to account for
this.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Message-Id: <8db966fa2f9803d6454ce773863025d0e2e7f3cc.1607620209.git.thomas.lendacky@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Allocate a page during vCPU creation to be used as the encrypted VM save
area (VMSA) for the SEV-ES guest. Provide a flag in the kvm_vcpu_arch
structure that indicates whether the guest state is protected.
When freeing a VMSA page that has been encrypted, the cache contents must
be flushed using the MSR_AMD64_VM_PAGE_FLUSH before freeing the page.
[ i386 build warnings ]
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Message-Id: <fde272b17eec804f3b9db18c131262fe074015c5.1607620209.git.thomas.lendacky@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add support to KVM for determining if a system is capable of supporting
SEV-ES as well as determining if a guest is an SEV-ES guest.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Message-Id: <e66792323982c822350e40c7a1cf67ea2978a70b.1607620209.git.thomas.lendacky@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM does not have separate ASIDs for L1 and L2; either the nested
hypervisor and nested guests share a single ASID, or on older processor
the ASID is used only to implement TLB flushing.
Either way, ASIDs are handled at the VM level. In preparation
for having different VMCBs passed to VMLOAD/VMRUN/VMSAVE for L1 and
L2, store the current ASID to struct vcpu_svm and only move it to
the VMCB in svm_vcpu_run. This way, TLB flushes can be applied
no matter which VMCB will be active during the next svm_vcpu_run.
Signed-off-by: Cathy Avery <cavery@redhat.com>
Message-Id: <20201011184818.3609-2-cavery@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Split out VMX's checks on CR4.VMXE to a dedicated hook, .is_valid_cr4(),
and invoke the new hook from kvm_valid_cr4(). This fixes an issue where
KVM_SET_SREGS would return success while failing to actually set CR4.
Fixing the issue by explicitly checking kvm_x86_ops.set_cr4()'s return
in __set_sregs() is not a viable option as KVM has already stuffed a
variety of vCPU state.
Note, kvm_valid_cr4() and is_valid_cr4() have different return types and
inverted semantics. This will be remedied in a future patch.
Fixes: 5e1746d620 ("KVM: nVMX: Allow setting the VMXE bit in CR4")
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20201007014417.29276-5-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This way we don't waste memory on VMs which don't use nesting
virtualization even when the host enabled it for them.
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20201001112954.6258-5-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This will be used to signal an error to the userspace, in case
the vendor code failed during handling of this msr. (e.g -ENOMEM)
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20201001112954.6258-4-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We will introduce the concept of MSRs that may not be handled in kernel
space soon. Some MSRs are directly passed through to the guest, effectively
making them handled by KVM from user space's point of view.
This patch introduces all logic required to ensure that MSRs that
user space wants trapped are not marked as direct access for guests.
Signed-off-by: Alexander Graf <graf@amazon.com>
Message-Id: <20200925143422.21718-6-graf@amazon.com>
[Make terminology a bit more similar to VMX. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 761e416934 created a wrong mask for the
CR3 MBZ bits. According to APM vol 2, only the upper 12 bits are MBZ.
Fixes: 761e416934 ("KVM: nSVM: Check that MBZ bits in CR3 and CR4 are not set on vmrun of nested guests", 2020-07-08)
Signed-off-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Message-Id: <20200829004824.4577-2-krish.sadhukhan@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert all the intercepts to one array of 32 bit vectors in
vmcb_control_area. This makes it easy for future intercept vector
additions. Also update trace functions.
Signed-off-by: Babu Moger <babu.moger@amd.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Message-Id: <159985250813.11252.5736581193881040525.stgit@bmoger-ubuntu>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Modify intercept_exceptions to generic intercepts in vmcb_control_area. Use
the generic vmcb_set_intercept, vmcb_clr_intercept and vmcb_is_intercept to
set/clear/test the intercept_exceptions bits.
Signed-off-by: Babu Moger <babu.moger@amd.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Message-Id: <159985250037.11252.1361972528657052410.stgit@bmoger-ubuntu>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Modify intercept_dr to generic intercepts in vmcb_control_area. Use
the generic vmcb_set_intercept, vmcb_clr_intercept and vmcb_is_intercept
to set/clear/test the intercept_dr bits.
Signed-off-by: Babu Moger <babu.moger@amd.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Message-Id: <159985249255.11252.10000868032136333355.stgit@bmoger-ubuntu>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Change intercept_cr to generic intercepts in vmcb_control_area.
Use the new vmcb_set_intercept, vmcb_clr_intercept and vmcb_is_intercept
where applicable.
Signed-off-by: Babu Moger <babu.moger@amd.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Message-Id: <159985248506.11252.9081085950784508671.stgit@bmoger-ubuntu>
[Change constant names. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This is in preparation for the future intercept vector additions.
Add new functions vmcb_set_intercept, vmcb_clr_intercept and vmcb_is_intercept
using kernel APIs __set_bit, __clear_bit and test_bit espectively.
Signed-off-by: Babu Moger <babu.moger@amd.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Message-Id: <159985247876.11252.16039238014239824460.stgit@bmoger-ubuntu>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
host_intercept_exceptions is not used anywhere. Clean it up.
Signed-off-by: Babu Moger <babu.moger@amd.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Message-Id: <159985252277.11252.8819848322175521354.stgit@bmoger-ubuntu>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This is to be more consistient with VMX, and to support
upcoming addition of vmcb02
Hopefully no functional changes.
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20200827171145.374620-3-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some operations in enter_svm_guest_mode() may fail, e.g. currently
we suppress kvm_set_cr3() return value. Prepare the code to proparate
errors.
No functional change intended.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20200710141157.1640173-5-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
According to section "Canonicalization and Consistency Checks" in APM vol. 2
the following guest state is illegal:
"Any MBZ bit of CR3 is set."
"Any MBZ bit of CR4 is set."
Suggeted-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Message-Id: <1594168797-29444-3-git-send-email-krish.sadhukhan@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Match the naming with other nested svm functions.
No functional changes.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Message-Id: <20200625080325.28439-5-joro@8bytes.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make clear the symbols belong to the SVM code when they are built-in.
No functional changes.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Message-Id: <20200625080325.28439-4-joro@8bytes.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make it more clear what data structure these functions operate on.
No functional changes.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Message-Id: <20200625080325.28439-3-joro@8bytes.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Renaming is only needed in the svm.h header file.
No functional changes.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Message-Id: <20200625080325.28439-2-joro@8bytes.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Both the vcpu_vmx structure and the vcpu_svm structure have a
'last_cpu' field. Move the common field into the kvm_vcpu_arch
structure. For clarity, rename it to 'last_vmentry_cpu.'
Suggested-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Oliver Upton <oupton@google.com>
Reviewed-by: Peter Shier <pshier@google.com>
Message-Id: <20200603235623.245638-6-jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
According to the AMD manual, the effect of turning off EFER.SVME while a
guest is running is undefined. We make it leave guest mode immediately,
similar to the effect of clearing the VMX bit in MSR_IA32_FEAT_CTL.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now that the int_ctl field is stored in svm->nested.ctl.int_ctl, we can
use it instead of vcpu->arch.hflags to check whether L2 is running
in V_INTR_MASKING mode.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Extract the code that is needed to implement CLGI and STGI,
so that we can run it from VMRUN and vmexit (and in the future,
KVM_SET_NESTED_STATE). Skip the request for KVM_REQ_EVENT unless needed,
subsuming the evaluate_pending_interrupts optimization that is found
in enter_svm_guest_mode.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The control state changes on every L2->L0 vmexit, and we will have to
serialize it in the nested state. So keep it up to date in svm->nested.ctl
and just copy them back to the nested VMCB in nested_svm_vmexit.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In preparation for nested SVM save/restore, store all data that matters
from the VMCB control area into svm->nested. It will then become part
of the nested SVM state that is saved by KVM_SET_NESTED_STATE and
restored by KVM_GET_NESTED_STATE, just like the cached vmcs12 for nVMX.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Unmapping the nested VMCB in enter_svm_guest_mode is a bit of a wart,
since the map argument is not used elsewhere in the function. There are
just two callers, and those are also the place where kvm_vcpu_map is
called, so it is cleaner to unmap there.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
All events now inject vmexits before vmentry rather than after vmexit. Therefore,
exit_required is not set anymore and we can remove it.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This allows exceptions injected by the emulator to be properly delivered
as vmexits. The code also becomes simpler, because we can just let all
L0-intercepted exceptions go through the usual path. In particular, our
emulation of the VMX #DB exit qualification is very much simplified,
because the vmexit injection path can use kvm_deliver_exception_payload
to update DR6.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Report interrupts as allowed when the vCPU is in L2 and L2 is being run with
exit-on-interrupts enabled and EFLAGS.IF=1 (either on the host or on the guest
according to VINTR). Interrupts are always unblocked from L1's perspective
in this case.
While moving nested_exit_on_intr to svm.h, use INTERCEPT_INTR properly instead
of assuming it's zero (which it is of course).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move the architectural (non-KVM specific) interrupt/NMI/SMI blocking checks
to a separate helper so that they can be used in a future patch by
svm_check_nested_events().
No functional change intended.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
