mirror of
https://github.com/Fishwaldo/Star64_linux.git
synced 2025-05-11 09:43:48 +00:00
5625f965d7
WILC1000 is an IEEE 802.11 b/g/n IoT link controller module. The WILC1000 connects to Microchip AVR/SMART MCUs, SMART MPUs, and other processors with minimal resource requirements with a simple SPI/SDIO-to-Wi-Fi interface. WILC1000 driver has been part of staging for few years. With contributions from the community, it has improved significantly. Full driver review has helped in achieving the current state. The details for those reviews are captured in 1 & 2. [1]. https://lore.kernel.org/linux-wireless/1537957525-11467-1-git-send-email-ajay.kathat@microchip.com/ [2]. https://lore.kernel.org/linux-wireless/1562896697-8002-1-git-send-email-ajay.kathat@microchip.com/ Signed-off-by: Ajay Singh <ajay.kathat@microchip.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
47 lines
1.9 KiB
Text
47 lines
1.9 KiB
Text
# SPDX-License-Identifier: GPL-2.0
|
|
config WILC1000
|
|
tristate
|
|
help
|
|
Add support for the Atmel WILC1000 802.11 b/g/n SoC.
|
|
This provides Wi-FI over an SDIO or SPI interface, and
|
|
is usually found in IoT devices.
|
|
|
|
This module only support IEEE 802.11n WiFi.
|
|
|
|
config WILC1000_SDIO
|
|
tristate "Atmel WILC1000 SDIO (WiFi only)"
|
|
depends on CFG80211 && INET && MMC
|
|
select WILC1000
|
|
help
|
|
This module adds support for the SDIO interface of adapters using
|
|
WILC1000 chipset. The Atmel WILC1000 SDIO is a full speed interface.
|
|
It meets SDIO card specification version 2.0. The interface supports
|
|
the 1-bit/4-bit SD transfer mode at the clock range of 0-50 MHz.
|
|
The host can use this interface to read and write from any register
|
|
within the chip as well as configure the WILC1000 for data DMA.
|
|
To use this interface, pin9 (SDIO_SPI_CFG) must be grounded. Select
|
|
this if your platform is using the SDIO bus.
|
|
|
|
config WILC1000_SPI
|
|
tristate "Atmel WILC1000 SPI (WiFi only)"
|
|
depends on CFG80211 && INET && SPI
|
|
select WILC1000
|
|
select CRC7
|
|
help
|
|
This module adds support for the SPI interface of adapters using
|
|
WILC1000 chipset. The Atmel WILC1000 has a Serial Peripheral
|
|
Interface (SPI) that operates as a SPI slave. This SPI interface can
|
|
be used for control and for serial I/O of 802.11 data. The SPI is a
|
|
full-duplex slave synchronous serial interface that is available
|
|
immediately following reset when pin 9 (SDIO_SPI_CFG) is tied to
|
|
VDDIO. Select this if your platform is using the SPI bus.
|
|
|
|
config WILC1000_HW_OOB_INTR
|
|
bool "WILC1000 out of band interrupt"
|
|
depends on WILC1000_SDIO
|
|
help
|
|
This option enables out-of-band interrupt support for the WILC1000
|
|
chipset. This OOB interrupt is intended to provide a faster interrupt
|
|
mechanism for SDIO host controllers that don't support SDIO interrupt.
|
|
Select this option If the SDIO host controller in your platform
|
|
doesn't support SDIO time devision interrupt.
|