update Nano Pi Neo Plus 2(nanopineoplus2) DT (#743)

incorporate feed back from ThomasKaiser, arm-kernel list, and
Kernel commit 442e1f7e

Remove stuff that was incorrectly copied from Orange Pi PC2
Change white speces to tabs in the dts file

 add wifi power controller,  mmc1, mmc2
 fix typo s/orangepi/nanopi/, s/pus/plus/
 usb_otg set to host mode
 wifi fix from brcm,bcm43xx-fmac.txt
 remove functions on header pins: spi, ir, ehci 1&2, ohci 1&2, uart 1&2
 remove hdmi, de2, r-gpio-keys, mixer - not supported the board, reg_usb0_vbus

Signed-off-by: Antony Antony <antony@phenome.org>
This commit is contained in:
Antony Antony 2017-08-26 16:09:59 +02:00 committed by Mikhail
parent d3180af7bc
commit 66a3269524

View file

@ -8,15 +8,14 @@ index b296f10..f361a2a 100644
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-nanopi-neo2.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-nanopi-neo-plus2.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-nanopim1plus2.dtb
always := $(dtb-y)
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo-plus2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo-plus2.dts
new file mode 100644
index 0000000..93df9fd
index 0000000..f86db28
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo-plus2.dts
@@ -0,0 +1,256 @@
@@ -0,0 +1,260 @@
+/*
+ * Copyright (C) 2017 Antony Antony <antony@phenome.org>
+ * Copyright (C) 2016 ARM Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
@ -67,7 +66,7 @@ index 0000000..93df9fd
+
+/ {
+ model = "FriendlyARM NanoPi NEO Plus2";
+ compatible = "friendlyarm,nanopi-neo-pus2", "allwinner,sun50i-h5";
+ compatible = "friendlyarm,nanopi-neo-plus2", "allwinner,sun50i-h5";
+
+ reg_vcc3v3: vcc3v3 {
+ compatible = "regulator-fixed";
@ -89,29 +88,21 @@ index 0000000..93df9fd
+ compatible = "gpio-leds";
+
+ pwr {
+ label = "orangepi:green:pwr";
+ label = "nanopi:green:pwr";
+ gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+
+ status {
+ label = "orangepi:red:status";
+ label = "nanopi:red:status";
+ gpios = <&pio 0 20 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ r-gpio-keys {
+ compatible = "gpio-keys";
+
+ sw4 {
+ label = "sw4";
+ linux,code = <BTN_0>;
+ gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ reg_gmac_3v3: gmac-3v3 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_power_pin_nanopi>;
+ regulator-name = "gmac-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
@ -120,14 +111,32 @@ index 0000000..93df9fd
+ gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
+ };
+
+ reg_usb0_vbus: usb0-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb0-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
+ status = "okay";
+ vdd_cpux: gpio-regulator {
+ compatible = "regulator-gpio";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&vdd_cpux_r_npi>;
+
+ regulator-name = "vdd-cpux";
+ regulator-type = "voltage";
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-ramp-delay = <50>; /* 4ms */
+
+ gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>;
+ gpios-states = <0x1>;
+ states = <1100000 0x0
+ 1300000 0x1>;
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_en_npi>;
+ reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+ post-power-on-delay-ms = <200>;
+ };
+};
+
@ -139,22 +148,10 @@ index 0000000..93df9fd
+ status = "okay";
+};
+
+&de {
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&ehci2 {
+ status = "okay";
+};
+
+&ehci3 {
+ status = "okay";
+};
@ -168,16 +165,6 @@ index 0000000..93df9fd
+ status = "okay";
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&ir {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir_pins_a>;
+ status = "okay";
+};
+
+&mdio {
+ ext_rgmii_phy: ethernet-phy@7 {
+ compatible = "ethernet-phy-ieee802.3-c22";
@ -185,10 +172,6 @@ index 0000000..93df9fd
+ };
+};
+
+&mixer0 {
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
@ -198,48 +181,80 @@ index 0000000..93df9fd
+ status = "okay";
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins_a>;
+ vmmc-supply = <&reg_vcc3v3>;
+ vqmmc-supply = <&reg_vcc3v3>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ boot_device = <0>;
+ status = "okay";
+
+ /*
+ * WiFi driver support could be incomplete,
+ * wlan0 is able to see Base Stations, however not able to join.
+ */
+ brcmf: wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ };
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_8bit_pins>;
+ vmmc-supply = <&reg_vcc3v3>;
+ bus-width = <8>;
+ non-removable;
+ cap-mmc-hw-reset;
+ boot_device = <0>;
+ status = "okay";
+};
+
+&mmc2_8bit_pins {
+ /* Increase drive strength for DDR modes */
+ drive-strength = <40>;
+ /* eMMC is missing pull-ups */
+ bias-pull-up;
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&ohci2 {
+ status = "okay";
+};
+
+&ohci3 {
+ status = "okay";
+};
+
+&tcon0 {
+ status = "okay";
+&pio {
+ leds_npi: led_pins@0 {
+ pins = "PA10";
+ function = "gpio_out";
+ };
+ gmac_power_pin_nanopi: gmac_power_pin@0 {
+ pins = "PD6";
+ function = "gpio_out";
+ };
+};
+
+&spi0 {
+ status = "okay";
+ spi-flash@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "jedec,spi-nor";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <10000000>;
+ status = "okay";
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ partition@0 {
+ label = "uboot";
+ reg = <0x0 0x100000>;
+ };
+ partition@100000 {
+ label = "env";
+ reg = <0x100000 0x100000>;
+&r_pio {
+ leds_r_npi: led_pins@0 {
+ pins = "PL10";
+ function = "gpio_out";
+ };
+
+ vdd_cpux_r_npi: regulator_pins@0 {
+ allwinner,pins = "PL6";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ wifi_en_npi: wifi_en_pin {
+ pins = "PL7";
+ function = "gpio_out";
+ };
+};
+
@ -249,26 +264,15 @@ index 0000000..93df9fd
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "disabled";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "disabled";
+};
+
+&usb_otg {
+ dr_mode = "otg";
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usbphy {
+ /* USB Type-A ports' VBUS is always on */
+ usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+ usb0_vbus-supply = <&reg_usb0_vbus>;
+ status = "okay";
+};
--
2.9.3