Igor Pecovnik
61f7953842
Remove deprecated patches in most mainline kernels and adjust few configs.
2019-06-02 22:15:15 +02:00
Martin Ayotte
aa643138d7
copy board-odroidc2-add-uartA patch from dev to next
2019-06-02 15:00:21 -04:00
Igor Pečovnik
55ad41787a
Merge pull request #1395 from Koumes/tuner-t230c2
...
Fix "No signal" issue with DVB-T/T2 tuner MyGica T230C v2
2019-06-02 20:02:01 +02:00
mei
1d0f199473
[sunxi-dev][h6] update opp table ( #1394 )
...
use more powerfull 'cpuburn-a53' to do pressure test.
power meter shows that 'cpuburn-a53' consumes much more power than
'stress -c 4' in the same condition. 930mV is not enough when running
'cpuburn-a53' meanwhile 950mV is the minimum voltage.
When running 'cpuburn-a53' at 1.8G, h6 consumes lots of power and generate
such amount of heat that an active cooling is necessary otherwise h6
gets overheat and system crashes. Even with active cooling and heatsink
is in low temperature the junction temperature is still quit high that
it reaches about 88~90 ℃ . Maybe the high thermal resistance of plastic
package causes the problem.
2019-06-02 19:57:43 +02:00
Koumes
c1e284e09c
si2168: add cmd timeout fix
2019-06-01 21:30:18 +00:00
may
7d0c6a2d71
10mV step according to AXP805 datasheet
2019-06-01 13:58:51 +08:00
Igor Pecovnik
b82c88191b
[ s5p6818 next ] patches and kernel adjustements
2019-05-31 21:34:43 +02:00
Igor Pecovnik
94cbeae168
[ odroidn2 ] Adjust and add upstream patch
2019-05-31 20:18:51 +02:00
Igor Pecovnik
f7edc91c8f
[ sunxi next ] Adjust patches
2019-05-31 19:40:38 +02:00
Igor Pecovnik
f7030069f4
[ rockchip-next ] remove deprecated patches, adjust kernel configuration
2019-05-31 19:08:48 +02:00
mei
634ec8f5da
patches clean up and fix lite2 usb3.0 port(works but only usb2.0 part) ( #1390 )
...
* [sunxi-dev][h6]update orangepi lite2 dts file patch
* [sunxi-dev][h6]update patch for sun50i-h6.dtsi
* [sunxi-dev][h6] new operation voltage table of allwinner h6
The correct operation voltages are find out after many reboots and test (over 20+).
the original 1.16v@1.64/1.8GHz was too high since standard cell voltage
of 28nm@HPC is 0.9v, h6 got overheat very quickly over 110 Celsius and then system hangs,
a power-cycle off is needed to reset soc.
I use 'stress -c 4' to do pressure test, with a medium size passive heatsink on top of h6.
The pressure test proves that the soc has about 4 watt power consuming
that is much lesser than original 6~7.x watt when running at 1.8GHz(orangepi lite2 with
usb Ethernet rtl8153 and usb hub, wifi is connected but not used).
Soc runs much more stable and does not get overheat easily under heavy load
with new opp table.
* [sunxi-dev][h6] orangepi lite2 wifi fix
bcm43455-fmac is buggy, reset to bcm4329-fmac
2019-05-31 18:05:46 +02:00
Igor Pecovnik
fb30186165
[ mvebu64-next ] Adjust patches and configuration
2019-05-30 20:53:12 +02:00
Igor Pečovnik
718ae4c50a
Merge pull request #1304 from FlashBurnGitHub/master
...
[WIP] Fix for making the cpu scaling on EspressoBIN working
2019-05-30 20:14:00 +02:00
Igor Pecovnik
f7c634c2bb
[ odroidn2 / general ] further improvements with some general patches, kernel config adjustements, upstream patches, bump with version
2019-05-28 21:43:48 +02:00
Igor Pecovnik
33ec5f38da
[ rk3399-default ] upstream patches
2019-05-27 14:42:52 +02:00
Igor Pecovnik
45194e865f
[ sunxi-next ] Upstream patches
2019-05-26 17:44:55 +02:00
Igor Pecovnik
ffffbb9cd0
[ odroidn2 ] Remove deprecated patches, kernel config adjustements, added AUFS -> docker support, adding mainline targets which needs further adjustements ...
2019-05-20 15:17:40 +02:00
Igor Pecovnik
af5245a297
[ sunxi ] add upstream patch for 4.19.y and remove not supported build target for Banana M64
2019-05-19 16:29:23 +02:00
Martin Ayotte
7cd2f9ff58
fix missing ethernet0 alias lost during 5.1.y switch
2019-05-18 11:09:44 -04:00
Igor Pecovnik
79c1c27819
[ odroidxu4 dev ] Move to 5.1.y
2019-05-17 10:46:57 +02:00
Igor Pecovnik
dda974ecd7
[ bugfix ] fix broken patch
2019-05-17 08:11:46 +02:00
Martin Ayotte
54049e6c58
add dual w1 overlay for meson64
2019-05-16 15:17:37 -04:00
Martin Ayotte
80b816f93c
adjust meson64 patches under 5.1.y
2019-05-16 14:38:08 -04:00
Martin Ayotte
eac7e401c3
remove useless meson64 patches under 5.1.y
2019-05-16 14:37:36 -04:00
Martin Ayotte
8295a7fb61
remove usless patches for meson64 since 5.1.y
2019-05-16 13:57:26 -04:00
Martin Ayotte
0afdccfbe2
move meson64 to 5.1.y
2019-05-16 13:02:56 -04:00
Martin Ayotte
4dd70d1520
restore nanopim1plus2.eos
2019-05-16 09:33:20 -04:00
Igor Pecovnik
8d7ef421b6
[ sunxi-dev ] remove deprecated patch, added bt support for orangepi win, teste for building only
2019-05-16 12:19:03 +02:00
Igor Pecovnik
0205e530af
[ sunxi-next ] upstream patches
2019-05-16 12:17:37 +02:00
Martin Ayotte
840a1ff43f
fix OpiZeroPlus2 default regulator
2019-05-15 13:38:52 -04:00
Martin Ayotte
b791e39ffa
add missing H6 IR-RX
2019-05-14 17:59:57 -04:00
Martin Ayotte
79e0a668e7
add missing phy on OPiOne+
2019-05-14 16:32:22 -04:00
Martin Ayotte
23bb6358de
fix missing regulator-always-on for OPiLite2
2019-05-14 15:30:18 -04:00
Martin Ayotte
f52fa0fbce
fix xxx-teres-fixed
2019-05-13 17:50:18 -04:00
Data Plus
1951a89e35
Create add-nanopi-neo-core.patch
...
[ nanopi-neo-core ] Add support for eMMC within u-boot
2019-05-13 10:14:32 +03:00
Martin Ayotte
710a75f2fd
add h6-cpu-supply patch
2019-05-12 10:24:49 -04:00
Martin Ayotte
0ddffca0b9
fix orangepi3 eMMC patch
2019-05-11 11:27:58 -04:00
Igor Pecovnik
c4281e5957
a20 sunxi - write speed improvement. Need testings.
2019-05-11 11:59:32 +02:00
Igor Pecovnik
2bd7f8efbd
[ Odroid N2 ] Added Odroid N2 with mods necessary to build from sources. Made a few tests builds ... it works at least as good as stock.
2019-05-10 10:27:01 +02:00
Thomas McKahan
5df7a1ce50
[ Rockchip Next ] Fix w1-gpio overlay
2019-05-10 00:17:43 -04:00
Martin Ayotte
694c9a7024
fix typo in RUART overlay
2019-05-09 17:07:30 -04:00
Martin Ayotte
96013852af
add spi-spidev1 overlay since spi-spidev don't work on OPi3 because spi0 doesn't exist
2019-05-09 16:50:18 -04:00
Martin Ayotte
624adfd0cd
add sun50i-h6-ruart overlay
2019-05-09 15:03:40 -04:00
Martin Ayotte
e074919e5b
add R_UART to OPI3
2019-05-09 14:44:34 -04:00
Martin Ayotte
3b70763ca0
fix general-add-H6-UARTs patch
2019-05-09 12:01:05 -04:00
Martin Ayotte
bcf2180acb
remove useless patches for 5.1.y
2019-05-09 11:52:00 -04:00
Martin Ayotte
b79c38c86c
recreate OPiLite2 patch
2019-05-08 15:24:17 -04:00
Igor Pecovnik
9afdc70340
[ rockchip dev ] move to 5.1.y and adjust patches false permissions, add new patch to remove broken boards
2019-05-08 09:42:55 +02:00
martinayotte
e0ca135edc
remove mmc1 duplicate in orangepi3
2019-05-07 21:56:42 -04:00
martinayotte
fbbea7fe82
fix H6 opp according to 5.1.y
2019-05-07 20:52:57 -04:00
