diff --git a/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt b/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt index cbc7847..0f00abd 100644 --- a/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt +++ b/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt @@ -11,6 +11,7 @@ Required properties: * allwinner,sun8i-a33-usb-phy * allwinner,sun8i-a83t-usb-phy * allwinner,sun8i-h3-usb-phy + * allwinner,sun8i-r40-usb-phy * allwinner,sun8i-v3s-usb-phy * allwinner,sun50i-a64-usb-phy - reg : a list of offset + length pairs diff --git a/Documentation/devicetree/bindings/sound/sun4i-i2s.txt b/Documentation/devicetree/bindings/sound/sun4i-i2s.txt index fc5da60..597dcd4 100644 --- a/Documentation/devicetree/bindings/sound/sun4i-i2s.txt +++ b/Documentation/devicetree/bindings/sound/sun4i-i2s.txt @@ -8,6 +8,7 @@ Required properties: - compatible: should be one of the following: - "allwinner,sun4i-a10-i2s" - "allwinner,sun6i-a31-i2s" + - "allwinner,sun8i-a83t-i2s" - "allwinner,sun8i-h3-i2s" - reg: physical base address of the controller and length of memory mapped region. @@ -23,6 +24,7 @@ Required properties: Required properties for the following compatibles: - "allwinner,sun6i-a31-i2s" + - "allwinner,sun8i-a83t-i2s" - "allwinner,sun8i-h3-i2s" - resets: phandle to the reset line for this codec diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 6817198..2fd4d80 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -936,6 +936,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \ sun8i-h3-orangepi-zeroplus2.dtb \ sun8i-r16-bananapi-m2m.dtb \ sun8i-r16-parrot.dtb \ + sun8i-r40-bananapi-m2-ultra.dtb \ sun8i-v3s-licheepi-zero.dtb \ sun8i-v3s-licheepi-zero-dock.dtb dtb-$(CONFIG_MACH_SUN9I) += \ diff --git a/arch/arm/boot/dts/axp81x.dtsi b/arch/arm/boot/dts/axp81x.dtsi new file mode 100644 index 0000000..73b761f --- /dev/null +++ b/arch/arm/boot/dts/axp81x.dtsi @@ -0,0 +1,139 @@ +/* + * Copyright 2017 Chen-Yu Tsai + * + * Chen-Yu Tsai + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/* AXP813/818 Integrated Power Management Chip */ + +&axp81x { + interrupt-controller; + #interrupt-cells = <1>; + + regulators { + /* Default work frequency for buck regulators */ + x-powers,dcdc-freq = <3000>; + + reg_dcdc1: dcdc1 { + }; + + reg_dcdc2: dcdc2 { + }; + + reg_dcdc3: dcdc3 { + }; + + reg_dcdc4: dcdc4 { + }; + + reg_dcdc5: dcdc5 { + }; + + reg_dcdc6: dcdc6 { + }; + + reg_dcdc7: dcdc7 { + }; + + reg_aldo1: aldo1 { + }; + + reg_aldo2: aldo2 { + }; + + reg_aldo3: aldo3 { + }; + + reg_dldo1: dldo1 { + }; + + reg_dldo2: dldo2 { + }; + + reg_dldo3: dldo3 { + }; + + reg_dldo4: dldo4 { + }; + + reg_eldo1: eldo1 { + }; + + reg_eldo2: eldo2 { + }; + + reg_eldo3: eldo3 { + }; + + reg_fldo1: fldo1 { + }; + + reg_fldo2: fldo2 { + }; + + reg_fldo3: fldo3 { + }; + + reg_ldo_io0: ldo-io0 { + /* Disable by default to avoid conflicts with GPIO */ + status = "disabled"; + }; + + reg_ldo_io1: ldo-io1 { + /* Disable by default to avoid conflicts with GPIO */ + status = "disabled"; + }; + + reg_rtc_ldo: rtc-ldo { + /* RTC_LDO is a fixed, always-on regulator */ + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + reg_sw: sw { + }; + + reg_drivevbus: drivevbus { + status = "disabled"; + }; + }; +}; diff --git a/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts b/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts old mode 100644 new mode 100755 index 2bafd7e..01a1f29 --- a/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +++ b/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts @@ -44,7 +44,6 @@ /dts-v1/; #include "sun8i-a83t.dtsi" -#include "sunxi-common-regulators.dtsi" #include @@ -53,12 +52,41 @@ compatible = "sinovoip,bpi-m3", "allwinner,sun8i-a83t"; aliases { + ethernet0 = &emac; serial0 = &uart0; }; chosen { stdout-path = "serial0:115200n8"; }; + + reg_vcc3v3: vcc3v3 { + compatible = "regulator-fixed"; + regulator-name = "vcc3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + reg_usb1_vbus: reg-usb1-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb1-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + enable-active-high; + gpio = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */ + }; + + wifi_pwrseq: wifi_pwrseq { + compatible = "mmc-pwrseq-simple"; + clocks = <&ac100_rtc 1>; + clock-names = "ext_clock"; + /* The WiFi low power clock must be 32768 Hz */ + assigned-clocks = <&ac100_rtc 1>; + assigned-clock-rates = <32768>; + /* enables internal regulator and de-asserts reset */ + reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 WL-PMU-EN */ + }; }; &ehci0 { @@ -68,6 +96,24 @@ /* TODO GL830 USB-to-SATA bridge downstream w/ GPIO power controls */ }; +&emac { + pinctrl-names = "default"; + pinctrl-0 = <&emac_rgmii_pins>; + phy-supply = <®_sw>; + phy-handle = <&rgmii_phy>; + phy-mode = "rgmii"; + allwinner,rx-delay-ps = <700>; + allwinner,tx-delay-ps = <700>; + status = "okay"; +}; + +&mdio { + rgmii_phy: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; +}; + &mmc0 { pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins>; @@ -78,6 +124,23 @@ status = "okay"; }; +&mmc1 { + vmmc-supply = <®_dldo1>; + vqmmc-supply = <®_dldo1>; + mmc-pwrseq = <&wifi_pwrseq>; + bus-width = <4>; + non-removable; + status = "okay"; + + brcmf: wifi@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + interrupt-parent = <&r_pio>; + interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>; + interrupt-names = "host-wake"; + }; +}; + &mmc2 { pinctrl-names = "default"; pinctrl-0 = <&mmc2_8bit_emmc_pins>; @@ -96,6 +159,10 @@ reg = <0x3a3>; interrupt-parent = <&r_intc>; interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + eldoin-supply = <®_dcdc1>; + fldoin-supply = <®_dcdc5>; + swin-supply = <®_dcdc1>; + x-powers,drive-vbus-en; }; ac100: codec@e89 { @@ -123,17 +190,126 @@ }; }; -®_usb1_vbus { - gpio = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */ +#include "axp81x.dtsi" + +®_aldo1 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-1v8"; +}; + +®_aldo2 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "dram-pll"; +}; + +®_aldo3 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "avcc"; +}; + +®_dcdc1 { + /* schematics says 3.1V but FEX file says 3.3V */ + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-3v3"; +}; + +®_dcdc2 { + regulator-always-on; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpua"; +}; + +®_dcdc3 { + regulator-always-on; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpub"; +}; + +®_dcdc4 { + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-gpu"; +}; + +®_dcdc5 { + regulator-always-on; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "vcc-dram"; +}; + +®_dcdc6 { + regulator-always-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + regulator-name = "vdd-sys"; +}; + +®_dldo1 { + /* + * This powers both the WiFi/BT module's main power, I/O supply, + * and external pull-ups on all the data lines. It should be set + * to the same voltage as the I/O supply (DCDC1 in this case) to + * avoid any leakage or mismatch. + */ + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi"; +}; + +®_dldo3 { + regulator-always-on; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-name = "vcc-pd"; +}; + +®_drivevbus { + regulator-name = "usb0-vbus"; status = "okay"; }; -®_vcc3v0 { - status = "disabled"; +®_fldo1 { + regulator-min-microvolt = <1080000>; + regulator-max-microvolt = <1320000>; + regulator-name = "vdd12-hsic"; +}; + +®_fldo2 { + /* + * Despite the embedded CPUs core not being used in any way, + * this must remain on or the system will hang. + */ + regulator-always-on; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpus"; +}; + +®_rtc_ldo { + regulator-name = "vcc-rtc"; }; -®_vcc5v0 { - status = "disabled"; +®_sw { + /* + * The PHY requires 20ms after all voltages + * are applied until core logic is ready and + * 30ms after the reset pin is de-asserted. + * Set a 100ms delay to account for PMIC + * ramp time and board traces. + */ + regulator-enable-ramp-delay = <100000>; + regulator-name = "vcc-ephy"; }; &uart0 { diff --git a/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts b/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts index 716a205..6da08cd 100644 --- a/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts +++ b/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts @@ -44,7 +44,6 @@ /dts-v1/; #include "sun8i-a83t.dtsi" -#include "sunxi-common-regulators.dtsi" #include @@ -53,6 +52,7 @@ compatible = "cubietech,cubietruck-plus", "allwinner,sun8i-a83t"; aliases { + ethernet0 = &emac; serial0 = &uart0; }; @@ -95,6 +95,26 @@ refclk-frequency = <19200000>; }; + reg_usb1_vbus: reg-usb1-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb1-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + enable-active-high; + gpio = <&pio 3 29 GPIO_ACTIVE_HIGH>; /* PD29 */ + }; + + reg_usb2_vbus: reg-usb2-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb2-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + enable-active-high; + gpio = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */ + }; + sound { compatible = "simple-audio-card"; simple-audio-card,name = "On-board SPDIF"; @@ -112,6 +132,17 @@ #sound-dai-cells = <0>; compatible = "linux,spdif-dit"; }; + + wifi_pwrseq: wifi_pwrseq { + compatible = "mmc-pwrseq-simple"; + clocks = <&ac100_rtc 1>; + clock-names = "ext_clock"; + /* The WiFi low power clock must be 32768 Hz */ + assigned-clocks = <&ac100_rtc 1>; + assigned-clock-rates = <32768>; + /* enables internal regulator and de-asserts reset */ + reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 WL-PMU-EN */ + }; }; &ehci0 { @@ -124,20 +155,45 @@ status = "okay"; }; +&emac { + pinctrl-names = "default"; + pinctrl-0 = <&emac_rgmii_pins>; + phy-supply = <®_dldo4>; + phy-handle = <&rgmii_phy>; + phy-mode = "rgmii"; + status = "okay"; +}; + +&mdio { + rgmii_phy: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; +}; + &mmc0 { pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins>; - vmmc-supply = <®_vcc3v3>; + vmmc-supply = <®_dcdc1>; bus-width = <4>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */ cd-inverted; status = "okay"; }; +&mmc1 { + vmmc-supply = <®_dcdc1>; + vqmmc-supply = <®_sw>; + mmc-pwrseq = <&wifi_pwrseq>; + bus-width = <4>; + non-removable; + status = "okay"; +}; + &mmc2 { pinctrl-names = "default"; pinctrl-0 = <&mmc2_8bit_emmc_pins>; - vmmc-supply = <®_vcc3v3>; + vmmc-supply = <®_dcdc1>; bus-width = <8>; non-removable; cap-mmc-hw-reset; @@ -152,6 +208,9 @@ reg = <0x3a3>; interrupt-parent = <&r_intc>; interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + eldoin-supply = <®_dcdc1>; + swin-supply = <®_dcdc1>; + x-powers,drive-vbus-en; }; ac100: codec@e89 { @@ -179,22 +238,143 @@ }; }; -®_usb1_vbus { - gpio = <&pio 3 29 GPIO_ACTIVE_HIGH>; /* PD29 */ - status = "okay"; +#include "axp81x.dtsi" + +®_aldo1 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-1v8"; +}; + +®_aldo2 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "dram-pll"; +}; + +®_aldo3 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "avcc"; +}; + +®_dcdc1 { + /* + * The schematics say this should be 3.3V, but the FEX file says + * it should be 3V. The latter makes sense, as the WiFi module's + * I/O is indirectly powered from DCDC1, through SW. It is rated + * at 2.98V maximum. + */ + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "vcc-3v"; +}; + +®_dcdc2 { + regulator-always-on; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpua"; +}; + +®_dcdc3 { + regulator-always-on; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpub"; +}; + +®_dcdc4 { + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-gpu"; +}; + +®_dcdc5 { + regulator-always-on; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-name = "vcc-dram"; +}; + +®_dcdc6 { + regulator-always-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + regulator-name = "vdd-sys"; +}; + +®_dldo2 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "dp-pwr"; }; -®_usb2_vbus { - gpio = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */ +®_dldo3 { + regulator-always-on; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-name = "ephy-io"; +}; + +®_dldo4 { + /* + * The PHY requires 20ms after all voltages are applied until core + * logic is ready and 30ms after the reset pin is de-asserted. + * Set a 100ms delay to account for PMIC ramp time and board traces. + */ + regulator-enable-ramp-delay = <100000>; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "ephy"; +}; + +®_drivevbus { + regulator-name = "usb0-vbus"; status = "okay"; }; -®_vcc3v0 { - status = "disabled"; +®_eldo1 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "dp-bridge-1"; +}; + +®_eldo2 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "dp-bridge-2"; +}; + +®_fldo1 { + /* TODO should be handled by USB PHY */ + regulator-always-on; + regulator-min-microvolt = <1080000>; + regulator-max-microvolt = <1320000>; + regulator-name = "vdd12-hsic"; +}; + +®_fldo2 { + /* + * Despite the embedded CPUs core not being used in any way, + * this must remain on or the system will hang. + */ + regulator-always-on; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpus"; +}; + +®_rtc_ldo { + regulator-name = "vcc-rtc"; }; -®_vcc5v0 { - status = "disabled"; +®_sw { + regulator-name = "vcc-wifi-io"; }; &spdif { diff --git a/arch/arm/boot/dts/sun8i-a83t.dtsi b/arch/arm/boot/dts/sun8i-a83t.dtsi index f996bd3..952923a 100644 --- a/arch/arm/boot/dts/sun8i-a83t.dtsi +++ b/arch/arm/boot/dts/sun8i-a83t.dtsi @@ -54,12 +54,6 @@ #address-cells = <1>; #size-cells = <1>; - aliases { - }; - - chosen { - }; - cpus { #address-cells = <1>; #size-cells = <0>; @@ -218,6 +212,8 @@ resets = <&ccu RST_BUS_MMC1>; reset-names = "ahb"; interrupts = ; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; status = "disabled"; #address-cells = <1>; #size-cells = <0>; @@ -242,7 +238,7 @@ #size-cells = <0>; }; - usb_otg: usb@01c19000 { + usb_otg: usb@1c19000 { compatible = "allwinner,sun8i-a83t-musb", "allwinner,sun8i-a33-musb"; reg = <0x01c19000 0x0400>; @@ -340,6 +336,39 @@ #interrupt-cells = <3>; #gpio-cells = <3>; + emac_rgmii_pins: emac-rgmii-pins { + pins = "PD2", "PD3", "PD4", "PD5", "PD6", "PD7", + "PD11", "PD12", "PD13", "PD14", "PD18", + "PD19", "PD21", "PD22", "PD23"; + function = "gmac"; + /* + * data lines in RGMII mode use DDR mode + * and need a higher signal drive strength + */ + drive-strength = <40>; + }; + + i2c0_pins: i2c0-pins { + pins = "PH0", "PH1"; + function = "i2c0"; + }; + + i2c1_pins: i2c1-pins { + pins = "PH2", "PH3"; + function = "i2c1"; + }; + + i2c2_ph_pins: i2c2-ph-pins { + pins = "PH4", "PH5"; + function = "i2c2"; + }; + + i2s1_pins: i2s1-pins { + /* I2S1 does not have external MCLK pin */ + pins = "PG10", "PG11", "PG12", "PG13"; + function = "i2s1"; + }; + mmc0_pins: mmc0-pins { pins = "PF0", "PF1", "PF2", "PF3", "PF4", "PF5"; @@ -348,6 +377,14 @@ bias-pull-up; }; + mmc1_pins: mmc1-pins { + pins = "PG0", "PG1", "PG2", + "PG3", "PG4", "PG5"; + function = "mmc1"; + drive-strength = <30>; + bias-pull-up; + }; + mmc2_8bit_emmc_pins: mmc2-8bit-emmc-pins { pins = "PC5", "PC6", "PC8", "PC9", "PC10", "PC11", "PC12", "PC13", @@ -371,6 +408,16 @@ pins = "PF2", "PF4"; function = "uart0"; }; + + uart1_pins: uart1-pins { + pins = "PG6", "PG7"; + function = "uart1"; + }; + + uart1_rts_cts_pins: uart1-rts-cts-pins { + pins = "PG8", "PG9"; + function = "uart1"; + }; }; timer@1c20c00 { @@ -404,7 +451,48 @@ status = "disabled"; }; - uart0: serial@01c28000 { + i2s0: i2s@1c22000 { + #sound-dai-cells = <0>; + compatible = "allwinner,sun8i-a83t-i2s"; + reg = <0x01c22000 0x400>; + interrupts = ; + clocks = <&ccu CLK_BUS_I2S0>, <&ccu CLK_I2S0>; + clock-names = "apb", "mod"; + dmas = <&dma 3>, <&dma 3>; + resets = <&ccu RST_BUS_I2S0>; + dma-names = "rx", "tx"; + status = "disabled"; + }; + + i2s1: i2s@1c22400 { + #sound-dai-cells = <0>; + compatible = "allwinner,sun8i-a83t-i2s"; + reg = <0x01c22400 0x400>; + interrupts = ; + clocks = <&ccu CLK_BUS_I2S1>, <&ccu CLK_I2S1>; + clock-names = "apb", "mod"; + dmas = <&dma 4>, <&dma 4>; + resets = <&ccu RST_BUS_I2S1>; + dma-names = "rx", "tx"; + pinctrl-names = "default"; + pinctrl-0 = <&i2s1_pins>; + status = "disabled"; + }; + + i2s2: i2s@1c22800 { + #sound-dai-cells = <0>; + compatible = "allwinner,sun8i-a83t-i2s"; + reg = <0x01c22800 0x400>; + interrupts = ; + clocks = <&ccu CLK_BUS_I2S2>, <&ccu CLK_I2S2>; + clock-names = "apb", "mod"; + dmas = <&dma 27>; + resets = <&ccu RST_BUS_I2S2>; + dma-names = "tx"; + status = "disabled"; + }; + + uart0: serial@1c28000 { compatible = "snps,dw-apb-uart"; reg = <0x01c28000 0x400>; interrupts = ; @@ -415,6 +503,78 @@ status = "disabled"; }; + i2c0: i2c@1c2ac00 { + compatible = "allwinner,sun8i-a83t-i2c", + "allwinner,sun6i-a31-i2c"; + reg = <0x01c2ac00 0x400>; + interrupts = ; + clocks = <&ccu CLK_BUS_I2C0>; + resets = <&ccu RST_BUS_I2C0>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c1: i2c@1c2b000 { + compatible = "allwinner,sun8i-a83t-i2c", + "allwinner,sun6i-a31-i2c"; + reg = <0x01c2b000 0x400>; + interrupts = ; + clocks = <&ccu CLK_BUS_I2C1>; + resets = <&ccu RST_BUS_I2C1>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c2: i2c@1c2b400 { + compatible = "allwinner,sun8i-a83t-i2c", + "allwinner,sun6i-a31-i2c"; + reg = <0x01c2b400 0x400>; + interrupts = ; + clocks = <&ccu CLK_BUS_I2C2>; + resets = <&ccu RST_BUS_I2C2>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + emac: ethernet@1c30000 { + compatible = "allwinner,sun8i-a83t-emac"; + syscon = <&syscon>; + reg = <0x01c30000 0x104>; + interrupts = ; + interrupt-names = "macirq"; + resets = <&ccu 13>; + reset-names = "stmmaceth"; + clocks = <&ccu 27>; + clock-names = "stmmaceth"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + + mdio: mdio { + compatible = "snps,dwmac-mdio"; + #address-cells = <1>; + #size-cells = <0>; + }; + }; + + uart1: serial@1c28400 { + compatible = "snps,dw-apb-uart"; + reg = <0x01c28400 0x400>; + interrupts = ; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&ccu CLK_BUS_UART1>; + resets = <&ccu RST_BUS_UART1>; + status = "disabled"; + }; + gic: interrupt-controller@1c81000 { compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic"; reg = <0x01c81000 0x1000>, diff --git a/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts b/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts new file mode 100644 index 0000000..5587d72 --- /dev/null +++ b/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts @@ -0,0 +1,228 @@ +/* + * Copyright (C) 2017 Chen-Yu Tsai + * Copyright (C) 2017 Icenowy Zheng + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "sun8i-r40.dtsi" + +#include + +/ { + model = "Banana Pi BPI-M2-Ultra"; + compatible = "sinovoip,bpi-m2-ultra", "allwinner,sun8i-r40"; + + aliases { + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + leds { + compatible = "gpio-leds"; + + pwr-led { + label = "bananapi:red:pwr"; + gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + + user-led-green { + label = "bananapi:green:user"; + gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>; + }; + + user-led-blue { + label = "bananapi:blue:user"; + gpios = <&pio 7 22 GPIO_ACTIVE_HIGH>; + }; + }; + + reg_vcc5v0: vcc5v0 { + compatible = "regulator-fixed"; + regulator-name = "vcc5v0"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&pio 7 23 GPIO_ACTIVE_HIGH>; /* PH23 */ + enable-active-high; + }; + + wifi_pwrseq: wifi_pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&pio 6 10 GPIO_ACTIVE_LOW>; /* PG10 WIFI_EN */ + }; +}; + +&ehci1 { + status = "okay"; +}; + +&ehci2 { + status = "okay"; +}; + +&i2c0 { + status = "okay"; + + axp22x: pmic@34 { + compatible = "x-powers,axp221"; + reg = <0x34>; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + }; +}; + +#include "axp22x.dtsi" + +&ahci { + vdd1v2-supply = <®_eldo3>; + vdd2v5-supply = <®_dldo4>; + status = "okay"; +}; + +®_aldo3 { + regulator-always-on; + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <3300000>; + regulator-name = "avcc"; +}; + +®_dldo4 { + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-name = "vdd-2v5-sata"; +}; + +®_eldo3 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "vdd-1v2-sata"; +}; + +®_dcdc1 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "vcc-3v0"; +}; + +®_dcdc2 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1300000>; + regulator-name = "vdd-cpu"; +}; + +®_dcdc3 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1300000>; + regulator-name = "vdd-sys"; +}; + +®_dcdc5 { + regulator-always-on; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-name = "vcc-dram"; +}; + +®_dldo1 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi-io"; +}; + +®_dldo2 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi"; +}; + +&mmc0 { + vmmc-supply = <®_dcdc1>; + bus-width = <4>; + cd-gpios = <&pio 7 13 GPIO_ACTIVE_HIGH>; /* PH13 */ + cd-inverted; + status = "okay"; +}; + +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pg_pins>; + vmmc-supply = <®_dldo2>; + vqmmc-supply = <®_dldo1>; + mmc-pwrseq = <&wifi_pwrseq>; + bus-width = <4>; + non-removable; + status = "okay"; +}; + +&mmc2 { + vmmc-supply = <®_dcdc1>; + vqmmc-supply = <®_dcdc1>; + bus-width = <8>; + non-removable; + status = "okay"; +}; + +&ohci1 { + status = "okay"; +}; + +&ohci2 { + status = "okay"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pb_pins>; + status = "okay"; +}; + +&usbphy { + usb1_vbus-supply = <®_vcc5v0>; + usb2_vbus-supply = <®_vcc5v0>; + pinctrl-names = "default"; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/sun8i-r40.dtsi b/arch/arm/boot/dts/sun8i-r40.dtsi new file mode 100755 index 0000000..ef4df3b --- /dev/null +++ b/arch/arm/boot/dts/sun8i-r40.dtsi @@ -0,0 +1,482 @@ +/* + * Copyright 2017 Chen-Yu Tsai + * Copyright 2017 Icenowy Zheng + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include +#include +#include + +/ { + #address-cells = <1>; + #size-cells = <1>; + interrupt-parent = <&gic>; + + clocks { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + osc24M: osc24M { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <24000000>; + clock-output-names = "osc24M"; + }; + + osc32k: osc32k { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <32768>; + clock-output-names = "osc32k"; + }; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + compatible = "arm,cortex-a7"; + device_type = "cpu"; + reg = <0>; + }; + + cpu@1 { + compatible = "arm,cortex-a7"; + device_type = "cpu"; + reg = <1>; + }; + + cpu@2 { + compatible = "arm,cortex-a7"; + device_type = "cpu"; + reg = <2>; + }; + + cpu@3 { + compatible = "arm,cortex-a7"; + device_type = "cpu"; + reg = <3>; + }; + }; + + soc { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + nmi_intc: interrupt-controller@1c00030 { + compatible = "allwinner,sun7i-a20-sc-nmi"; + interrupt-controller; + #interrupt-cells = <2>; + reg = <0x01c00030 0x0c>; + interrupts = ; + }; + + mmc0: mmc@1c0f000 { + compatible = "allwinner,sun8i-r40-mmc", + "allwinner,sun50i-a64-mmc"; + reg = <0x01c0f000 0x1000>; + clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>; + clock-names = "ahb", "mmc"; + resets = <&ccu RST_BUS_MMC0>; + reset-names = "ahb"; + pinctrl-0 = <&mmc0_pins>; + pinctrl-names = "default"; + interrupts = ; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + mmc1: mmc@1c10000 { + compatible = "allwinner,sun8i-r40-mmc", + "allwinner,sun50i-a64-mmc"; + reg = <0x01c10000 0x1000>; + clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>; + clock-names = "ahb", "mmc"; + resets = <&ccu RST_BUS_MMC1>; + reset-names = "ahb"; + interrupts = ; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + mmc2: mmc@1c11000 { + compatible = "allwinner,sun8i-r40-emmc", + "allwinner,sun50i-a64-emmc"; + reg = <0x01c11000 0x1000>; + clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>; + clock-names = "ahb", "mmc"; + resets = <&ccu RST_BUS_MMC2>; + reset-names = "ahb"; + pinctrl-0 = <&mmc2_pins>; + pinctrl-names = "default"; + interrupts = ; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + mmc3: mmc@1c12000 { + compatible = "allwinner,sun8i-r40-mmc", + "allwinner,sun50i-a64-mmc"; + reg = <0x01c12000 0x1000>; + clocks = <&ccu CLK_BUS_MMC3>, <&ccu CLK_MMC3>; + clock-names = "ahb", "mmc"; + resets = <&ccu RST_BUS_MMC3>; + reset-names = "ahb"; + interrupts = ; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + usbphy: phy@1c13400 { + compatible = "allwinner,sun8i-r40-usb-phy"; + reg = <0x01c13400 0x14>, + <0x01c14800 0x4>, + <0x01c19800 0x4>, + <0x01c1c800 0x4>; + reg-names = "phy_ctrl", + "pmu0", + "pmu1", + "pmu2"; + clocks = <&ccu CLK_USB_PHY0>, + <&ccu CLK_USB_PHY1>, + <&ccu CLK_USB_PHY2>; + clock-names = "usb0_phy", + "usb1_phy", + "usb2_phy"; + resets = <&ccu RST_USB_PHY0>, + <&ccu RST_USB_PHY1>, + <&ccu RST_USB_PHY2>; + reset-names = "usb0_reset", + "usb1_reset", + "usb2_reset"; + status = "disabled"; + #phy-cells = <1>; + }; + + ehci1: usb@1c19000 { + compatible = "allwinner,sun8i-r40-ehci", "generic-ehci"; + reg = <0x01c19000 0x100>; + interrupts = ; + clocks = <&ccu CLK_BUS_EHCI1>; + resets = <&ccu RST_BUS_EHCI1>; + phys = <&usbphy 1>; + phy-names = "usb"; + status = "okay"; + }; + + ohci1: usb@1c19400 { + compatible = "allwinner,sun8i-r40-ohci", "generic-ohci"; + reg = <0x01c19400 0x100>; + interrupts = ; + clocks = <&ccu CLK_BUS_OHCI1>, + <&ccu CLK_USB_OHCI1>; + resets = <&ccu RST_BUS_OHCI1>; + phys = <&usbphy 1>; + phy-names = "usb"; + status = "disabled"; + }; + + ehci2: usb@1c1c000 { + compatible = "allwinner,sun8i-r40-ehci", "generic-ehci"; + reg = <0x01c1c000 0x100>; + interrupts = ; + clocks = <&ccu CLK_BUS_EHCI2>; + resets = <&ccu RST_BUS_EHCI2>; + phys = <&usbphy 2>; + phy-names = "usb"; + status = "okay"; + }; + + ohci2: usb@1c1c400 { + compatible = "allwinner,sun8i-r40-ohci", "generic-ohci"; + reg = <0x01c1c400 0x100>; + interrupts = ; + clocks = <&ccu CLK_BUS_OHCI2>, + <&ccu CLK_USB_OHCI2>; + resets = <&ccu RST_BUS_OHCI2>; + phys = <&usbphy 2>; + phy-names = "usb"; + status = "disabled"; + }; + + ahci: sata@1c18000 { + compatible = "allwinner,sun8i-r40-ahci", "allwinner,sun4i-a10-ahci"; + reg = <0x01c18000 0x1000>; + interrupts = ; + clocks = <&ccu CLK_SATA>, <&ccu CLK_BUS_SATA>; + resets = <&ccu RST_BUS_SATA>; + status = "enabled"; + }; + + ccu: clock@1c20000 { + compatible = "allwinner,sun8i-r40-ccu"; + reg = <0x01c20000 0x400>; + clocks = <&osc24M>, <&osc32k>; + clock-names = "hosc", "losc"; + #clock-cells = <1>; + #reset-cells = <1>; + }; + + pio: pinctrl@1c20800 { + compatible = "allwinner,sun8i-r40-pinctrl"; + reg = <0x01c20800 0x400>; + interrupts = ; + clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>; + clock-names = "apb", "hosc", "losc"; + gpio-controller; + interrupt-controller; + #interrupt-cells = <3>; + #gpio-cells = <3>; + + i2c0_pins: i2c0-pins { + pins = "PB0", "PB1"; + function = "i2c0"; + }; + + mmc0_pins: mmc0-pins { + pins = "PF0", "PF1", "PF2", + "PF3", "PF4", "PF5"; + function = "mmc0"; + drive-strength = <30>; + bias-pull-up; + }; + + mmc1_pg_pins: mmc1-pg-pins { + pins = "PG0", "PG1", "PG2", + "PG3", "PG4", "PG5"; + function = "mmc1"; + drive-strength = <30>; + bias-pull-up; + }; + + mmc2_pins: mmc2-pins { + pins = "PC5", "PC6", "PC7", "PC8", "PC9", + "PC10", "PC11", "PC12", "PC13", "PC14", + "PC15", "PC24"; + function = "mmc2"; + drive-strength = <30>; + bias-pull-up; + }; + + uart0_pb_pins: uart0-pb-pins { + pins = "PB22", "PB23"; + function = "uart0"; + }; + }; + + wdt: watchdog@1c20c90 { + compatible = "allwinner,sun4i-a10-wdt"; + reg = <0x01c20c90 0x10>; + }; + + uart0: serial@1c28000 { + compatible = "snps,dw-apb-uart"; + reg = <0x01c28000 0x400>; + interrupts = ; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&ccu CLK_BUS_UART0>; + resets = <&ccu RST_BUS_UART0>; + status = "disabled"; + }; + + uart1: serial@1c28400 { + compatible = "snps,dw-apb-uart"; + reg = <0x01c28400 0x400>; + interrupts = ; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&ccu CLK_BUS_UART1>; + resets = <&ccu RST_BUS_UART1>; + status = "disabled"; + }; + + uart2: serial@1c28800 { + compatible = "snps,dw-apb-uart"; + reg = <0x01c28800 0x400>; + interrupts = ; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&ccu CLK_BUS_UART2>; + resets = <&ccu RST_BUS_UART2>; + status = "disabled"; + }; + + uart3: serial@1c28c00 { + compatible = "snps,dw-apb-uart"; + reg = <0x01c28c00 0x400>; + interrupts = ; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&ccu CLK_BUS_UART3>; + resets = <&ccu RST_BUS_UART3>; + status = "disabled"; + }; + + uart4: serial@1c29000 { + compatible = "snps,dw-apb-uart"; + reg = <0x01c29000 0x400>; + interrupts = ; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&ccu CLK_BUS_UART4>; + resets = <&ccu RST_BUS_UART4>; + status = "disabled"; + }; + + uart5: serial@1c29400 { + compatible = "snps,dw-apb-uart"; + reg = <0x01c29400 0x400>; + interrupts = ; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&ccu CLK_BUS_UART5>; + resets = <&ccu RST_BUS_UART5>; + status = "disabled"; + }; + + uart6: serial@1c29800 { + compatible = "snps,dw-apb-uart"; + reg = <0x01c29800 0x400>; + interrupts = ; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&ccu CLK_BUS_UART6>; + resets = <&ccu RST_BUS_UART6>; + status = "disabled"; + }; + + uart7: serial@1c29c00 { + compatible = "snps,dw-apb-uart"; + reg = <0x01c29c00 0x400>; + interrupts = ; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&ccu CLK_BUS_UART7>; + resets = <&ccu RST_BUS_UART7>; + status = "disabled"; + }; + + i2c0: i2c@1c2ac00 { + compatible = "allwinner,sun6i-a31-i2c"; + reg = <0x01c2ac00 0x400>; + interrupts = ; + clocks = <&ccu CLK_BUS_I2C0>; + resets = <&ccu RST_BUS_I2C0>; + pinctrl-0 = <&i2c0_pins>; + pinctrl-names = "default"; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c1: i2c@1c2b000 { + compatible = "allwinner,sun6i-a31-i2c"; + reg = <0x01c2b000 0x400>; + interrupts = ; + clocks = <&ccu CLK_BUS_I2C1>; + resets = <&ccu RST_BUS_I2C1>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c2: i2c@1c2b400 { + compatible = "allwinner,sun6i-a31-i2c"; + reg = <0x01c2b400 0x400>; + interrupts = ; + clocks = <&ccu CLK_BUS_I2C2>; + resets = <&ccu RST_BUS_I2C2>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c3: i2c@1c2b800 { + compatible = "allwinner,sun6i-a31-i2c"; + reg = <0x01c2b800 0x400>; + interrupts = ; + clocks = <&ccu CLK_BUS_I2C3>; + resets = <&ccu RST_BUS_I2C3>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c4: i2c@1c2c000 { + compatible = "allwinner,sun6i-a31-i2c"; + reg = <0x01c2c000 0x400>; + interrupts = ; + clocks = <&ccu CLK_BUS_I2C4>; + resets = <&ccu RST_BUS_I2C4>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + gic: interrupt-controller@1c81000 { + compatible = "arm,gic-400"; + reg = <0x01c81000 0x1000>, + <0x01c82000 0x1000>, + <0x01c84000 0x2000>, + <0x01c86000 0x2000>; + interrupt-controller; + #interrupt-cells = <3>; + interrupts = ; + }; + }; + + timer { + compatible = "arm,armv7-timer"; + interrupts = , + , + , + ; + }; +}; diff --git a/drivers/phy/allwinner/phy-sun4i-usb.c b/drivers/phy/allwinner/phy-sun4i-usb.c index 1161e11..9df7a2c 100644 --- a/drivers/phy/allwinner/phy-sun4i-usb.c +++ b/drivers/phy/allwinner/phy-sun4i-usb.c @@ -112,6 +112,7 @@ enum sun4i_usb_phy_type { sun8i_a33_phy, sun8i_a83t_phy, sun8i_h3_phy, + sun8i_r40_phy, sun8i_v3s_phy, sun50i_a64_phy, }; @@ -919,6 +920,16 @@ static const struct sun4i_usb_phy_cfg sun8i_h3_cfg = { .phy0_dual_route = true, }; +static const struct sun4i_usb_phy_cfg sun8i_r40_cfg = { + .num_phys = 3, + .type = sun8i_r40_phy, + .disc_thresh = 3, + .phyctl_offset = REG_PHYCTL_A33, + .dedicated_clocks = true, + .enable_pmu_unk1 = true, + .phy0_dual_route = true, +}; + static const struct sun4i_usb_phy_cfg sun8i_v3s_cfg = { .num_phys = 1, .type = sun8i_v3s_phy, @@ -947,6 +958,7 @@ static const struct of_device_id sun4i_usb_phy_of_match[] = { { .compatible = "allwinner,sun8i-a33-usb-phy", .data = &sun8i_a33_cfg }, { .compatible = "allwinner,sun8i-a83t-usb-phy", .data = &sun8i_a83t_cfg }, { .compatible = "allwinner,sun8i-h3-usb-phy", .data = &sun8i_h3_cfg }, + { .compatible = "allwinner,sun8i-r40-usb-phy", .data = &sun8i_r40_cfg }, { .compatible = "allwinner,sun8i-v3s-usb-phy", .data = &sun8i_v3s_cfg }, { .compatible = "allwinner,sun50i-a64-usb-phy", .data = &sun50i_a64_cfg}, diff --git a/sound/soc/sunxi/sun4i-i2s.c b/sound/soc/sunxi/sun4i-i2s.c index 7826fb3..1a7fef8 100644 --- a/sound/soc/sunxi/sun4i-i2s.c +++ b/sound/soc/sunxi/sun4i-i2s.c @@ -905,6 +905,23 @@ static const struct sun4i_i2s_quirks sun6i_a31_i2s_quirks = { .field_rxchansel = REG_FIELD(SUN4I_I2S_RX_CHAN_SEL_REG, 0, 2), }; +static const struct sun4i_i2s_quirks sun8i_a83t_i2s_quirks = { + .has_reset = true, + .reg_offset_txdata = SUN8I_I2S_FIFO_TX_REG, + .sun4i_i2s_regmap = &sun4i_i2s_regmap_config, + .field_clkdiv_mclk_en = REG_FIELD(SUN4I_I2S_CLK_DIV_REG, 7, 7), + .field_fmt_wss = REG_FIELD(SUN4I_I2S_FMT0_REG, 2, 3), + .field_fmt_sr = REG_FIELD(SUN4I_I2S_FMT0_REG, 4, 5), + .field_fmt_bclk = REG_FIELD(SUN4I_I2S_FMT0_REG, 6, 6), + .field_fmt_lrclk = REG_FIELD(SUN4I_I2S_FMT0_REG, 7, 7), + .has_slave_select_bit = true, + .field_fmt_mode = REG_FIELD(SUN4I_I2S_FMT0_REG, 0, 1), + .field_txchanmap = REG_FIELD(SUN4I_I2S_TX_CHAN_MAP_REG, 0, 31), + .field_rxchanmap = REG_FIELD(SUN4I_I2S_RX_CHAN_MAP_REG, 0, 31), + .field_txchansel = REG_FIELD(SUN4I_I2S_TX_CHAN_SEL_REG, 0, 2), + .field_rxchansel = REG_FIELD(SUN4I_I2S_RX_CHAN_SEL_REG, 0, 2), +}; + static const struct sun4i_i2s_quirks sun8i_h3_i2s_quirks = { .has_reset = true, .reg_offset_txdata = SUN8I_I2S_FIFO_TX_REG, @@ -1136,6 +1153,10 @@ static const struct of_device_id sun4i_i2s_match[] = { .data = &sun6i_a31_i2s_quirks, }, { + .compatible = "allwinner,sun8i-a83t-i2s", + .data = &sun8i_a83t_i2s_quirks, + }, + { .compatible = "allwinner,sun8i-h3-i2s", .data = &sun8i_h3_i2s_quirks, },