mirror of
https://github.com/Fishwaldo/build.git
synced 2025-03-25 16:21:32 +00:00
91 lines
2 KiB
Diff
91 lines
2 KiB
Diff
diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts b/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts
|
|
old mode 100644
|
|
new mode 100755
|
|
index 03ff6f8..ddbb92b
|
|
--- a/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts
|
|
+++ b/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts
|
|
@@ -47,7 +47,7 @@
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
|
|
/ {
|
|
- model = "FriendlyARM NanoPi NEO Air";
|
|
+ model = "FriendlyElec NanoPi NEO Air";
|
|
compatible = "friendlyarm,nanopi-neo-air", "allwinner,sun8i-h3";
|
|
|
|
aliases {
|
|
@@ -58,6 +58,13 @@
|
|
stdout-path = "serial0:115200n8";
|
|
};
|
|
|
|
+ wifi_pwrseq: wifi_pwrseq {
|
|
+ compatible = "mmc-pwrseq-simple";
|
|
+ pinctrl-names = "default";
|
|
+ pinctrl-0 = <&wifi_en_neoair>;
|
|
+ reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
|
|
+ };
|
|
+
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
@@ -70,10 +77,18 @@
|
|
status {
|
|
label = "nanopi:blue:status";
|
|
gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>; /* PA10 */
|
|
+ linux,default-trigger = "heartbeat";
|
|
};
|
|
};
|
|
};
|
|
|
|
+&r_pio {
|
|
+ wifi_en_neoair: wifi_en_pin@0 {
|
|
+ allwinner,pins = "PL7";
|
|
+ allwinner,function = "gpio_out";
|
|
+ };
|
|
+};
|
|
+
|
|
&mmc0 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
|
|
@@ -84,6 +99,42 @@
|
|
status = "okay";
|
|
};
|
|
|
|
+&mmc1 {
|
|
+ pinctrl-names = "default";
|
|
+ pinctrl-0 = <&mmc1_pins_a>;
|
|
+ vmmc-supply = <®_vcc3v3>;
|
|
+ vqmmc-supply = <®_vcc3v3>;
|
|
+ mmc-pwrseq = <&wifi_pwrseq>;
|
|
+ bus-width = <4>;
|
|
+ non-removable;
|
|
+ status = "okay";
|
|
+
|
|
+ brcmf: bcrmf@1 {
|
|
+ reg = <1>;
|
|
+ compatible = "brcm,bcm4329-fmac";
|
|
+ interrupt-parent = <&pio>;
|
|
+ interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
|
|
+ interrupt-names = "host-wake";
|
|
+ };
|
|
+};
|
|
+
|
|
+&mmc2 {
|
|
+ pinctrl-names = "default";
|
|
+ pinctrl-0 = <&mmc2_8bit_pins>;
|
|
+ vmmc-supply = <®_vcc3v3>;
|
|
+ bus-width = <8>;
|
|
+ non-removable;
|
|
+ cap-mmc-hw-reset;
|
|
+ status = "okay";
|
|
+};
|
|
+
|
|
+&mmc2_8bit_pins {
|
|
+ /* Increase drive strength for DDR modes */
|
|
+ drive-strength = <40>;
|
|
+ /* eMMC is missing pull-ups */
|
|
+ bias-pull-up;
|
|
+};
|
|
+
|
|
&uart0 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&uart0_pins_a>;
|