build/patch/kernel/sunxi-dev/xxx-teres-fixed.patch

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dts
index c455b24dd..9f018de23 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dts
@@ -19,6 +19,15 @@
 
 	aliases {
 		serial0 = &uart0;
+		ethernet0 = &rtl8723bs;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 0 50000 0>;
+		brightness-levels = <0 5 10 15 20 30 40 55 70 85 100>;
+		default-brightness-level = <2>;
+		enable-gpios = <&pio 3 23 GPIO_ACTIVE_HIGH>; /* PD23 */
 	};
 
 	chosen {
@@ -42,6 +51,17 @@
 		};
 	};
 
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 
@@ -66,26 +86,83 @@
 		status = "okay";
 	};
 
+	speaker_amp: speaker_amp {
+		compatible = "simple-audio-amplifier";
+		VCC-supply = <&reg_aldo2>;
+		enable-gpios = <&r_pio 0 12 GPIO_ACTIVE_HIGH>; /*PL12*/
+	};
+
 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
 	};
 };
 
+&codec {
+	status = "okay";
+};
+
+&codec_analog {
+	status = "okay";
+};
+
+&dai {
+	status = "okay";
+};
+
+&de {
+	status = "okay";
+};
+
+&ehci0 {
+	phys = <&usbphy 0>;
+	phy-names = "usb";
+	status = "okay";
+};
+
 &ehci1 {
 	status = "okay";
 };
 
 
-/* The ANX6345 eDP-bridge is on i2c0. There is no linux (mainline)
- * driver for this chip at the moment, the bootloader initializes it.
- * However it can be accessed with the i2c-dev driver from user space.
- */
 &i2c0 {
 	clock-frequency = <100000>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c0_pins>;
 	status = "okay";
+
+	anx6345: anx6345@38 {
+		compatible = "analogix,anx6345";
+		reg = <0x38>;
+		reset-gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */
+		dvdd25-supply = <&reg_dldo2>;
+		dvdd12-supply = <&reg_dldo3>;
+
+		port {
+			anx6345_in: endpoint {
+				remote-endpoint = <&tcon0_out_anx6345>;
+			};
+		};
+	};
+};
+
+&hdmi {
+	hvcc-supply = <&reg_dldo1>;
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&i2s2 {
+	status = "okay";
+};
+
+&mixer0 {
+	status = "okay";
 };
 
 &mmc0 {
@@ -127,6 +204,12 @@
 	status = "okay";
 };
 
+&ohci0 {
+	phys = <&usbphy 0>;
+	phy-names = "usb";
+	status = "okay";
+};
+
 &ohci1 {
 	status = "okay";
 };
@@ -143,6 +230,29 @@
 	};
 };
 
+&sound {
+	status = "okay";
+	simple-audio-card,aux-devs = <&codec_analog>, <&speaker_amp>;
+	simple-audio-card,widgets = "Microphone", "Internal Microphone Left",
+				"Microphone", "Internal Microphone Right",
+				"Headphone", "Headphone Jack",
+				"Speaker", "Internal Speaker";
+	simple-audio-card,routing =
+			"Left DAC", "AIF1 Slot 0 Left",
+			"Right DAC", "AIF1 Slot 0 Right",
+			"Speaker Amp INL", "LINEOUT",
+			"Speaker Amp INR", "LINEOUT",
+			"Internal Speaker", "Speaker Amp OUTL",
+			"Internal Speaker", "Speaker Amp OUTR",
+			"Headphone Jack", "HP",
+			"AIF1 Slot 0 Left ADC", "Left ADC",
+			"AIF1 Slot 0 Right ADC", "Right ADC",
+			"Internal Microphone Left", "MBIAS",
+			"MIC1", "Internal Microphone Left",
+			"Internal Microphone Right", "HBIAS",
+			"MIC2", "Internal Microphone Right";
+};
+
 #include "axp803.dtsi"
 
 &ac_power_supply {
@@ -266,12 +376,48 @@
 	vcc-hdmi-supply = <&reg_dldo1>;
 };
 
+&sound_hdmi {
+	status = "okay";
+};
+
+&tcon0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&lcd_rgb666_pins>;
+
+	status = "okay";
+};
+
+&tcon0_out {
+	tcon0_out_anx6345: endpoint@0 {
+		reg = <0>;
+		remote-endpoint = <&anx6345_in>;
+	};
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pb_pins>;
 	status = "okay";
 };
 
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+	status = "okay";
+
+	bluetooth {
+		compatible = "realtek,rtl8723bs-bt";
+		reset-gpios = <&r_pio 0 4 GPIO_ACTIVE_LOW>; /* PL4 */
+		device-wake-gpios = <&r_pio 0 5 GPIO_ACTIVE_HIGH>; /* PL5 */
+		host-wake-gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
+		firmware-postfix = "teres";
+	};
+};
+
+&usb_otg {
+	dr_mode = "host";
+};
+
 &usbphy {
 	usb1_vbus-supply = <&reg_usb1_vbus>;
 	status = "okay";