mirror of
https://github.com/Fishwaldo/build.git
synced 2025-03-22 23:01:56 +00:00
123 lines
2.1 KiB
Diff
123 lines
2.1 KiB
Diff
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-zero-plus2.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-zero-plus2.dts
|
|
index b8f46e2..24cb8b9 100644
|
|
--- a/arch/arm/boot/dts/sun8i-h3-orangepi-zero-plus2.dts
|
|
+++ b/arch/arm/boot/dts/sun8i-h3-orangepi-zero-plus2.dts
|
|
@@ -53,12 +53,29 @@
|
|
|
|
aliases {
|
|
serial0 = &uart0;
|
|
+ ethernet1 = &brcmf;
|
|
};
|
|
|
|
chosen {
|
|
stdout-path = "serial0:115200n8";
|
|
};
|
|
|
|
+ leds {
|
|
+ compatible = "gpio-leds";
|
|
+
|
|
+ pwr_led {
|
|
+ label = "orangepi:green:pwr";
|
|
+ gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
|
|
+ default-state = "on";
|
|
+ };
|
|
+
|
|
+ status_led {
|
|
+ label = "orangepi:red:status";
|
|
+ gpios = <&pio 0 17 GPIO_ACTIVE_HIGH>;
|
|
+ linux,default-trigger = "heartbeat";
|
|
+ };
|
|
+ };
|
|
+
|
|
connector {
|
|
compatible = "hdmi-connector";
|
|
type = "a";
|
|
@@ -88,6 +105,11 @@
|
|
status = "okay";
|
|
};
|
|
|
|
+&ehci0 {
|
|
+ status = "okay";
|
|
+};
|
|
+
|
|
+
|
|
&hdmi {
|
|
status = "okay";
|
|
};
|
|
@@ -98,6 +120,22 @@
|
|
};
|
|
};
|
|
|
|
+&sound_hdmi {
|
|
+ status = "okay";
|
|
+};
|
|
+
|
|
+&i2s2 {
|
|
+ status = "okay";
|
|
+};
|
|
+
|
|
+&mixer0 {
|
|
+ status = "okay";
|
|
+};
|
|
+
|
|
+&tcon0 {
|
|
+ status = "okay";
|
|
+};
|
|
+
|
|
&mmc0 {
|
|
vmmc-supply = <®_vcc3v3>;
|
|
bus-width = <4>;
|
|
@@ -132,8 +170,53 @@
|
|
status = "okay";
|
|
};
|
|
|
|
+&pio {
|
|
+ bt_pwr_pin: bt_pwr_pin@0 {
|
|
+ pins = "PA10";
|
|
+ function = "gpio_out";
|
|
+ };
|
|
+};
|
|
+
|
|
+&ohci0 {
|
|
+ status = "okay";
|
|
+};
|
|
+
|
|
+&spi0 {
|
|
+ /* Disable SPI NOR by default: it optional on Orange Pi Zero boards */
|
|
+ status = "disabled";
|
|
+
|
|
+ flash@0 {
|
|
+ #address-cells = <1>;
|
|
+ #size-cells = <1>;
|
|
+ compatible = "mxicy,mx25l1606e", "winbond,w25q128";
|
|
+ reg = <0>;
|
|
+ spi-max-frequency = <40000000>;
|
|
+ };
|
|
+};
|
|
+
|
|
&uart0 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&uart0_pa_pins>;
|
|
status = "okay";
|
|
};
|
|
+
|
|
+&uart1 {
|
|
+ pinctrl-names = "default";
|
|
+ pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
|
|
+ status = "okay";
|
|
+};
|
|
+
|
|
+&usb_otg {
|
|
+ dr_mode = "peripheral";
|
|
+ status = "okay";
|
|
+};
|
|
+
|
|
+&usbphy {
|
|
+ /*
|
|
+ * USB Type-A port VBUS is always on. However, MicroUSB VBUS can only
|
|
+ * power up the board; when it's used as OTG port, this VBUS is
|
|
+ * always off even if the board is powered via GPIO pins.
|
|
+ */
|
|
+ status = "okay";
|
|
+ usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
|
|
+};
|