From d177c8b61d6b4ef360b1c2682e4d8e3bae01738b Mon Sep 17 00:00:00 2001
From: Icenowy Zheng <icenowy@aosc.io>
Date: Thu, 26 Jul 2018 12:48:05 +0800
Subject: [PATCH 1/4] arm64: allwinner: dts: h6: fix Pine H64 MMC bus width
Currently the enabled MMC controllers on Pine H64 do not have bus-width
set, which make them fall back to 1-bit mode and become quite slow.
Fix this by add the corresponding bus-width properties.
Fixes: ecbd611882a1 ("arm64: allwinner: h6: enable MMC0/2 on Pine H64")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
---
arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts
index ceffc40810ee..48daec7f78ba 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts
@@ -46,6 +46,7 @@
pinctrl-0 = <&mmc0_pins>;
vmmc-supply = <®_cldo1>;
cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
+ bus-width = <4>;
status = "okay";
};
@@ -56,6 +57,7 @@
vqmmc-supply = <®_bldo2>;
non-removable;
cap-mmc-hw-reset;
+ bus-width = <8>;
status = "okay";
};
From d07f05fb86439c41dd6967c94be3ba3837b21567 Mon Sep 17 00:00:00 2001
From: Peter Robinson <pbrobinson@gmail.com>
Date: Sat, 21 Jul 2018 00:02:12 +0100
Subject: [PATCH 2/4] hwmon: rpi: add module alias to raspberrypi-hwmon
The raspberrypi-hwmon driver doesn't automatically load, although it does work
when loaded, by adding the alias it auto loads as expected when built as a
module. Tested on RPi2/RPi3 on 32 bit kernel and RPi3B+ on aarch64 with
Fedora 28 and a patched 4.18 RC kernel.
Fixes: 3c493c885cf ("hwmon: Add support for RPi voltage sensor")
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
CC: Stefan Wahren <stefan.wahren@i2se.com>
CC: Eric Anholt <eric@anholt.net>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
---
drivers/hwmon/raspberrypi-hwmon.c | 1 +
1 file changed, 1 insertion(+)
diff --git a/drivers/hwmon/raspberrypi-hwmon.c b/drivers/hwmon/raspberrypi-hwmon.c
index fb4e4a6bb1f6..be5ba4690895 100644
--- a/drivers/hwmon/raspberrypi-hwmon.c
+++ b/drivers/hwmon/raspberrypi-hwmon.c
@@ -164,3 +164,4 @@ module_platform_driver(rpi_hwmon_driver);
MODULE_AUTHOR("Stefan Wahren <stefan.wahren@i2se.com>");
MODULE_DESCRIPTION("Raspberry Pi voltage sensor driver");
MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:raspberrypi-hwmon");
From 96d529bac562574600eda85726fcfa3eef6dde8e Mon Sep 17 00:00:00 2001
From: Sudeep Holla <sudeep.holla@arm.com>
Date: Thu, 6 Sep 2018 16:10:39 +0100
Subject: [PATCH 3/4] firmware: arm_scmi: fix divide by zero when
sustained_perf_level is zero
Firmware can provide zero as values for sustained performance level and
corresponding sustained frequency in kHz in order to hide the actual
frequencies and provide only abstract values. It may endup with divide
by zero scenario resulting in kernel panic.
Let's set the multiplication factor to one if either one or both of them
(sustained_perf_level and sustained_freq) are set to zero.
Fixes: a9e3fbfaa0ff ("firmware: arm_scmi: add initial support for performance protocol")
Reported-by: Ionela Voinescu <ionela.voinescu@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
---
drivers/firmware/arm_scmi/perf.c | 8 +++++++-
1 file changed, 7 insertions(+), 1 deletion(-)
diff --git a/drivers/firmware/arm_scmi/perf.c b/drivers/firmware/arm_scmi/perf.c
index 721e6c57beae..64342944d917 100644
--- a/drivers/firmware/arm_scmi/perf.c
+++ b/drivers/firmware/arm_scmi/perf.c
@@ -166,7 +166,13 @@ scmi_perf_domain_attributes_get(const struct scmi_handle *handle, u32 domain,
le32_to_cpu(attr->sustained_freq_khz);
dom_info->sustained_perf_level =
le32_to_cpu(attr->sustained_perf_level);
- dom_info->mult_factor = (dom_info->sustained_freq_khz * 1000) /
+ if (!dom_info->sustained_freq_khz ||
+ !dom_info->sustained_perf_level)
+ /* CPUFreq converts to kHz, hence default 1000 */
+ dom_info->mult_factor = 1000;
+ else
+ dom_info->mult_factor =
+ (dom_info->sustained_freq_khz * 1000) /
dom_info->sustained_perf_level;
memcpy(dom_info->name, attr->name, SCMI_MAX_STR_SIZE);
}
From 6b45a2b1c0bc2aec84d1c56a1976ca9c8a621ecb Mon Sep 17 00:00:00 2001
From: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Date: Thu, 6 Sep 2018 14:12:19 +0200
Subject: [PATCH 4/4] memory: ti-aemif: fix a potential NULL-pointer
dereference
Platform data pointer may be NULL. We check it everywhere but in one
place. Fix it.
Fixes: 8af70cd2ca50 ("memory: aemif: add support for board files")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: stable@vger.kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
---
drivers/memory/ti-aemif.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/memory/ti-aemif.c b/drivers/memory/ti-aemif.c
index 31112f622b88..475e5b3790ed 100644
--- a/drivers/memory/ti-aemif.c
+++ b/drivers/memory/ti-aemif.c
@@ -411,7 +411,7 @@ static int aemif_probe(struct platform_device *pdev)
if (ret < 0)
goto error;
}
- } else {
+ } else if (pdata) {
for (i = 0; i < pdata->num_sub_devices; i++) {
pdata->sub_devices[i].dev.parent = dev;
ret = platform_device_register(&pdata->sub_devices[i]);