The initial R8A7745 SoC device tree including CPU0, GIC, timer, SYSC, RST,
CPG, and the required clock descriptions.
Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the SK-RZG1M board dependent part of the Ether device node.
Enable DHCP and NFS root for the kernel booting.
Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the initial device tree for the R8A7743 SoC based SK-RZG1M board.
The board has one debug serial port (SCIF0); include support for it, so
that the serial console can work.
Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the IRQC interrupt controller in the R8A7743 device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A7743 part of the Ether device node.
Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe [H]SCIF{|A|B} ports in the R8A7743 device tree.
Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
[simon: consistently use tabs for indentation]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe SYS-DMAC0/1 in the R8A7743 device tree.
Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The initial R8A7743 SoC device tree including CPU0, GIC, timer, SYSC, RST,
CPG, and the required clock descriptions.
Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
And the sd-uhs-sdr104 property to SDHI0.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
And the sd-uhs-sdr104 property to SDHI0.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Add the sd-uhs-sdr104 property to SDHI0.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Make it possible to fallback to GPIO for I2C4 on the EXIO-B connector.
This is based on reference work for the I2C0 core of the lager/r8a7790
by Wolfram Sang.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
[wsa: rebased and fixed aliases]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Make it possible to fallback to GPIO for I2C1 on the EXIO-C connector.
This is based on reference work for the I2C0 core of the lager/r8a7790
by Wolfram Sang.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
[wsa: rebased and fixed aliases]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Make it possible to select which I2C1 IP core you want to run on the
EXIO-A connector.
This is based on reference work for the I2C0 core of the lager board
by Wolfram Sang.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
[wsa: rebased and fixed aliases]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
The rename from i2cexio to i2cexio0 is in preparation for adding
i2cexio1 which will use the demuxer for IIC1/I2C1.
The reindexing from i2c8 to i2c10 is to allow space for grouping of
additional GPIO buses to be added by follow-up patches to support demuxing
of other i2c buses.
Also note that fallback to GPIO is not provided by the hardware for IIC0/I2C0.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
[wsa: rebased, fixed alias and removed typo in commit message]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
The parent clock of the HSUSB clock is the HP clock, not the MP clock.
Fixes: c7bab9f929 ("ARM: shmobile: r8a7794: Add USB clocks to device tree")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Update the PFC pin groups and function names of DU interface for
r8a7794 ALT board.
The currently specified pin groups and function names prevented PFC and
DU interfaces from being correctly configured:
sh-pfc e6060000.pin-controller: function 'du' not supported
sh-pfc e6060000.pin-controller: invalid function du in map table
sh-pfc e6060000.pin-controller: function 'du' not supported
sh-pfc e6060000.pin-controller: invalid function du in map table
sh-pfc e6060000.pin-controller: function 'du' not supported
sh-pfc e6060000.pin-controller: invalid function du in map table
sh-pfc e6060000.pin-controller: function 'du' not supported
sh-pfc e6060000.pin-controller: invalid function du in map table
rcar-du: probe of feb00000.display failed with error -22
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Odroid XU3/4 didn't need to use the cd-gpios for detecting card.
Because host controller has the CDETECT register through SDx_CDN line.
Host controller can know whether card is inserted or not with this
register.
When I have checked the Odroid XU3/4, they are using CDETECT register
(not using exteranl cd-gpio).
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
devicetree binding for stmmac states:
- compatible: Should be "snps,dwmac-<ip_version>", "snps,dwmac"
For backwards compatibility: "st,spear600-gmac" is also supported.
No functional change intended.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The AM571x-IDK board is a board based on TI's AM5718 SOC
which has a single core 1.5GHz A15 processor. This board is a
development platform for the Industrial market with:
- 1GB of DDR3L
- Dual 1Gbps Ethernet
- HDMI,
- PRU-ICSS
- uSD
- 16GB eMMC
- CAN
- RS-485
- PCIe
- USB3.0
- Video Input Port
- Industrial IO port and expansion connector
The link to the data sheet and TRM can be found here:
http://www.ti.com/product/AM5718
Initial support is only for basic peripherals.
Signed-off-by: Schuyler Patton <spatton@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
phy-phandle is now a preferred method to reference a PHY device.
Especially in regards to cpsw it enables PHY specific settings like
max-speed etc. being specified in DTS.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The PMICs have POWERHOLD set by default which prevents PMIC shutdown
even on DEV_CTRL On bit set to 0 as the Powerhold has higher priority.
So to enable pmic power off this property lets one over ride the default
value and enable pmic power off.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The PMICs have POWERHOLD set by default which prevents PMIC shutdown
even on DEV_CTRL On bit set to 0 as the Powerhold has higher priority.
So to enable pmic power off this property lets one over ride the default
value and enable pmic power off.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The I2C nodes are missing #address-cells and #size-cells. This is
causing warning at device tree compilation when some I2C device
sub-nodes are defined.
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
The Hummingbird A31 board has a VGA DAC which converts RGB output
from the LCD interface to VGA analog signals.
Add nodes for the VGA DAC, its power supply, and enable this part
of the display pipeline.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Just like on sun8i all sun5i tablets use the same interrupt and power
gpios for their touchscreens. I've checked all known a13 fex files and
only the UTOO P66 uses a different gpio for the interrupt.
Add a touchscreen node to sun5i-reference-design-tablet.dtsi, which
fills in the necessary gpios to avoid duplication in the tablet dts files,
just like we do in sun8i-reference-design-tablet.dtsi.
This will make future patches adding touchscreen nodes to a13 tablets
simpler.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The pin controllers also use the two oscillators for debouncing. Add them
to the DTs.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The Bananapi M1+ supports USB OTG, with the PMIC doing VBUS sensing.
Enable the USB OTG related functions.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Bananapi M1+, like other Allwinner A20 based boards, uses the
AXP209 PMIC to supply its power.
Add the AXP209 regulators.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The 2 USB host ports are directly tied to the 2 USB hosts in the SoC.
The 2 host pairs were already enabled, but the USB PHY wasn't.
VBUS on the 2 ports are always on.
Enable the USB PHY.
Fixes: 04c85ecad3 ("ARM: dts: sun7i: Add dts file for Bananapi M1 Plus
board")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The micro-USB on the SinA33 has a somewhat interesting design in the sense
that it has a micro USB connector, but the VBUS is (supposed to be)
controlled through an (unpopulated) jumper.
Obviously, that doesn't work really well, and only the peripheral mode
really works. Still enable it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On some Q8 and other tablets ldo_io1 is used as vcc-touchscreen,
config at as such in sun8i-reference-design-tablet.dtsi.
Note that it will only be enabled when it us actually referenced by
a foo-supply property in the touchscreen node, so for tablets which
do not use ldo_io1 as vcc-touchscreen, it will be disabled.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Though the mmc core driver will continue to support the legacy
"enable-sdio-wakeup" property to enable SDIO as the wakeup source,
"wakeup-source" is the new standard binding.
This patch replaces the legacy "enable-sdio-wakeup" with the unified
"wakeup-source" property in order to avoid any further copy-paste
duplication.
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The GR8-EVB comes with a wm8978 codec connected to the i2s bus.
Add a card in order to have it working
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The SinA31s routes the SoC's LINEOUT pins to a line out jack, and MIC1
to a microphone jack, with MBIAS providing phantom power.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Hummingbird A31 has headset and line in audio jacks and an onboard
mic routed to the pins for the SoC's internal codec. The line out pins
are routed to an onboard speaker amp, whose output is available on a
pin header.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A31 SoC includes the Allwinner audio codec, capable of 24-bit
playback up to 192 kHz and 24-bit capture up to 48 kHz.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The GR8-EVB has a SPDIF out connector. Enable it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
H3 SPI subsystem is almost same as A31 SPI except buffer size, so those
DT properties are reusable.
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
H3 supports two SPI controllers. Four pins (MOSI, MISO, SCLK, SS) are
configured through the pinctrl subsystem.
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
NanoPi M1 is the Allwinner H3 based board.
This patch enables UART for debug console, LEDs, GPIO key switch, 3 USB
host ports, a micro SD slot and related power and pin controls by using
NanoPi common dtsi file.
Cc: James Pettigrew <james@innovum.com.au>
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
NanoPi common dtsi supports all components of NEO SBC, so just include it.
Cc: James Pettigrew <james@innovum.com.au>
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch provides a common file for NanoPi M1 and Neo SBC.
Those have common features below.
* UART0
* 2 LEDs
* USB host (EHCI3, OHCI3) and PHY
* MicroSD
* GPIO key switch
Cc: James Pettigrew <james@innovum.com.au>
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The board has a Ampak AP6330 WiFi/BT/FM module. Inside it is a Broadcom
BCM4330 WiFi/BT/FM combo IC. The WiFi portion is connected to mmc1, with
the enabling pin connected to PL2. The AC100 RTC provides a low power
clock signal.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The board has a Ampak AP6330 WiFi/BT/FM module. Inside it is a Broadcom
BCM4330 WiFi/BT/FM combo IC. The WiFi portion is connected to mmc1, with
the enabling pin connected to PL2. The AC100 RTC provides a low power
clock signal.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On the A80, mmc1 is available on pingroup G. Designs mostly use this
to connect to an SDIO WiFi chip.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The I2C1 and SPI2 buses are exposed on the CHIP headers, and are not
explicitly dedicated to anything.
Add them to the DTS with the muxing already set, but keep them disabled.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Some boards use the LCD in RGB565. Enable the pin muxing option.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
