Merge branch 'master' of git://git.denx.de/u-boot-i2c

* 'master' of git://git.denx.de/u-boot-i2c:
  mx28evk: Add I2C support
  mxs-i2c: Fix internal address byte order
  mxc_i2c: remove setting speed at each start
  mx6qsabrelite: add i2c support
  mxc_i2c: specify i2c base address in config file

Signed-off-by: Wolfgang Denk <wd@denx.de>

arch/arm/include/asm/arch-mx31/imx-regs.h

@@ -606,6 +606,13 @@ struct esdc_regs {
 #define UART4_BASE	0x43FB0000
 #define UART5_BASE	0x43FB4000
 
+#define I2C1_BASE_ADDR          0x43f80000
+#define I2C1_CLK_OFFSET		26
+#define I2C2_BASE_ADDR          0x43F98000
+#define I2C2_CLK_OFFSET		28
+#define I2C3_BASE_ADDR          0x43f84000
+#define I2C3_CLK_OFFSET		30
+
 #define ESDCTL_SDE			(1 << 31)
 #define ESDCTL_CMD_RW			(0 << 28)
 #define ESDCTL_CMD_PRECHARGE		(1 << 28)

arch/arm/include/asm/arch-mx35/imx-regs.h

@@ -39,7 +39,7 @@
 #define MAX_BASE_ADDR           0x43F04000
 #define EVTMON_BASE_ADDR        0x43F08000
 #define CLKCTL_BASE_ADDR        0x43F0C000
-#define I2C_BASE_ADDR           0x43F80000
+#define I2C1_BASE_ADDR		0x43F80000
 #define I2C3_BASE_ADDR          0x43F84000
 #define ATA_BASE_ADDR           0x43F8C000
 #define UART1_BASE		0x43F90000

board/freescale/mx28evk/iomux.c

@@ -159,6 +159,9 @@ const iomux_cfg_t iomux_setup[] = {
 	MX28_PAD_SSP2_MISO__SSP2_D0 | MUX_CONFIG_SSP2,
 	MX28_PAD_SSP2_SS0__SSP2_D3 |
 		(MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_PULLUP),
+	/* I2C */
+	MX28_PAD_I2C0_SCL__I2C0_SCL,
+	MX28_PAD_I2C0_SDA__I2C0_SDA,
 };
 
 #define HW_DRAM_CTL29	(0x74 >> 2)

board/freescale/mx6qsabrelite/mx6qsabrelite.c

@@ -55,6 +55,11 @@ DECLARE_GLOBAL_DATA_PTR;
 	PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED   |		\
 	PAD_CTL_DSE_40ohm   | PAD_CTL_HYS)
 
+#define I2C_PAD_CTRL	(PAD_CTL_PKE | PAD_CTL_PUE |		\
+	PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED |		\
+	PAD_CTL_DSE_40ohm | PAD_CTL_HYS |			\
+	PAD_CTL_ODE | PAD_CTL_SRE_FAST)
+
 int dram_init(void)
 {
        gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
@@ -72,6 +77,11 @@ iomux_v3_cfg_t uart2_pads[] = {
        MX6Q_PAD_EIM_D27__UART2_RXD | MUX_PAD_CTRL(UART_PAD_CTRL),
 };
 
+iomux_v3_cfg_t i2c3_pads[] = {
+	MX6Q_PAD_GPIO_5__I2C3_SCL | MUX_PAD_CTRL(I2C_PAD_CTRL),
+	MX6Q_PAD_GPIO_16__I2C3_SDA | MUX_PAD_CTRL(I2C_PAD_CTRL),
+};
+
 iomux_v3_cfg_t usdhc3_pads[] = {
        MX6Q_PAD_SD3_CLK__USDHC3_CLK   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
        MX6Q_PAD_SD3_CMD__USDHC3_CMD   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
@@ -336,6 +346,7 @@ int board_init(void)
 #ifdef CONFIG_MXC_SPI
 	setup_spi();
 #endif
+	imx_iomux_v3_setup_multiple_pads(i2c3_pads, ARRAY_SIZE(i2c3_pads));
 
 #ifdef CONFIG_CMD_SATA
 	setup_sata();

drivers/i2c/mxc_i2c.c

@@ -59,27 +59,10 @@ struct mxc_i2c_regs {
 #define I2SR_IIF	(1 << 1)
 #define I2SR_RX_NO_AK	(1 << 0)
 
-#if defined(CONFIG_SYS_I2C_MX31_PORT1)
+#ifdef CONFIG_SYS_I2C_BASE
-#define I2C_BASE	0x43f80000
+#define I2C_BASE	CONFIG_SYS_I2C_BASE
-#define I2C_CLK_OFFSET	26
-#elif defined (CONFIG_SYS_I2C_MX31_PORT2)
-#define I2C_BASE	0x43f98000
-#define I2C_CLK_OFFSET	28
-#elif defined (CONFIG_SYS_I2C_MX31_PORT3)
-#define I2C_BASE	0x43f84000
-#define I2C_CLK_OFFSET	30
-#elif defined(CONFIG_SYS_I2C_MX53_PORT1)
-#define I2C_BASE        I2C1_BASE_ADDR
-#elif defined(CONFIG_SYS_I2C_MX53_PORT2)
-#define I2C_BASE        I2C2_BASE_ADDR
-#elif defined(CONFIG_SYS_I2C_MX35_PORT1)
-#define I2C_BASE	I2C_BASE_ADDR
-#elif defined(CONFIG_SYS_I2C_MX35_PORT2)
-#define I2C_BASE	I2C2_BASE_ADDR
-#elif defined(CONFIG_SYS_I2C_MX35_PORT3)
-#define I2C_BASE	I2C3_BASE_ADDR
 #else
-#error "define CONFIG_SYS_I2C_MX<Processor>_PORTx to use the mx I2C driver"
+#error "define CONFIG_SYS_I2C_BASE to use the mxc_i2c driver"
 #endif
 
 #define I2C_MAX_TIMEOUT		10000
@@ -114,7 +97,7 @@ static uint8_t i2c_imx_get_clk(unsigned int rate)
 		(struct clock_control_regs *)CCM_BASE;
 
 	/* start the required I2C clock */
-	writel(readl(&sc_regs->cgr0) | (3 << I2C_CLK_OFFSET),
+	writel(readl(&sc_regs->cgr0) | (3 << CONFIG_SYS_I2C_CLK_OFFSET),
 		&sc_regs->cgr0);
 #endif
 
@@ -248,12 +231,6 @@ int i2c_imx_start(void)
 	struct mxc_i2c_regs *i2c_regs = (struct mxc_i2c_regs *)I2C_BASE;
 	unsigned int temp = 0;
 	int result;
-	int speed = i2c_get_bus_speed();
-	u8 clk_idx = i2c_imx_get_clk(speed);
-	u8 idx = i2c_clk_div[clk_idx][1];
-
-	/* Store divider value */
-	writeb(idx, &i2c_regs->ifdr);
 
 	/* Enable I2C controller */
 	writeb(0, &i2c_regs->i2sr);

drivers/i2c/mxs_i2c.c

@@ -97,7 +97,7 @@ void mxs_i2c_write(uchar chip, uint addr, int alen,
 
 	for (i = 0; i < alen; i++) {
 		data >>= 8;
-		data |= ((char *)&addr)[i] << 24;
+		data |= ((char *)&addr)[alen - i - 1] << 24;
 		if ((i & 3) == 2)
 			writel(data, &i2c_regs->hw_i2c_data);
 	}

include/configs/flea3.h

@@ -66,7 +66,7 @@
  */
 #define CONFIG_HARD_I2C
 #define CONFIG_I2C_MXC
-#define CONFIG_SYS_I2C_MX35_PORT3
+#define CONFIG_SYS_I2C_BASE		I2C3_BASE_ADDR
 #define CONFIG_SYS_I2C_SPEED		100000
 #define CONFIG_SYS_I2C_SLAVE		0xfe
 #define CONFIG_MXC_SPI

include/configs/imx31_phycore.h

@@ -54,7 +54,8 @@
 
 #define CONFIG_HARD_I2C
 #define CONFIG_I2C_MXC
-#define CONFIG_SYS_I2C_MX31_PORT2
+#define CONFIG_SYS_I2C_BASE		I2C2_BASE_ADDR
+#define CONFIG_SYS_I2C_CLK_OFFSET	I2C2_CLK_OFFSET
 #define CONFIG_SYS_I2C_SPEED		100000
 
 #define CONFIG_MXC_UART

include/configs/mx28evk.h

@@ -68,6 +68,7 @@
 #define CONFIG_CMD_SPI
 #define CONFIG_CMD_USB
 #define CONFIG_CMD_BOOTZ
+#define CONFIG_CMD_I2C
 
 /*
  * Memory configurations
@@ -188,6 +189,13 @@
 #define	CONFIG_USB_STORAGE
 #endif
 
+/* I2C */
+#ifdef CONFIG_CMD_I2C
+#define CONFIG_I2C_MXS
+#define CONFIG_HARD_I2C
+#define CONFIG_SYS_I2C_SPEED	400000
+#endif
+
 /*
  * SPI
  */

include/configs/mx35pdk.h

@@ -57,7 +57,7 @@
  */
 #define CONFIG_HARD_I2C
 #define CONFIG_I2C_MXC
-#define CONFIG_SYS_I2C_MX35_PORT1
+#define CONFIG_SYS_I2C_BASE		I2C1_BASE_ADDR
 #define CONFIG_SYS_I2C_SPEED		100000
 #define CONFIG_MXC_SPI
 #define CONFIG_MXC_GPIO

include/configs/mx53ard.h

@@ -50,7 +50,7 @@
 #define CONFIG_CMD_I2C
 #define CONFIG_HARD_I2C
 #define CONFIG_I2C_MXC
-#define CONFIG_SYS_I2C_MX53_PORT2
+#define CONFIG_SYS_I2C_BASE		I2C2_BASE_ADDR
 #define CONFIG_SYS_I2C_SPEED            100000
 
 /* MMC Configs */

include/configs/mx53evk.h

@@ -53,7 +53,7 @@
 #define CONFIG_CMD_I2C
 #define CONFIG_HARD_I2C
 #define CONFIG_I2C_MXC
-#define CONFIG_SYS_I2C_MX53_PORT2       1
+#define CONFIG_SYS_I2C_BASE		I2C2_BASE_ADDR
 #define CONFIG_SYS_I2C_SPEED            100000
 
 /* PMIC Configs */

include/configs/mx53loco.h

@@ -89,7 +89,7 @@
 /* I2C Configs */
 #define CONFIG_HARD_I2C
 #define CONFIG_I2C_MXC
-#define CONFIG_SYS_I2C_MX53_PORT1
+#define CONFIG_SYS_I2C_BASE		I2C1_BASE_ADDR
 #define CONFIG_SYS_I2C_SPEED		100000
 
 /* PMIC Controller */

include/configs/mx53smd.h

@@ -50,7 +50,7 @@
 #define CONFIG_CMD_I2C
 #define CONFIG_HARD_I2C
 #define CONFIG_I2C_MXC
-#define CONFIG_SYS_I2C_MX53_PORT2
+#define CONFIG_SYS_I2C_BASE		I2C2_BASE_ADDR
 #define CONFIG_SYS_I2C_SPEED            100000
 
 /* MMC Configs */

include/configs/mx6qsabrelite.h

@@ -58,6 +58,14 @@
 #define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0)
 #endif
 
+/* I2C Configs */
+#define CONFIG_CMD_I2C
+#define CONFIG_HARD_I2C
+#define CONFIG_I2C_MXC
+#define CONFIG_SYS_I2C_BASE		I2C3_BASE_ADDR
+#define CONFIG_SYS_I2C_SPEED            100000
+#define CONFIG_SYS_I2C_SLAVE            0xfe
+
 /* MMC Configs */
 #define CONFIG_FSL_ESDHC
 #define CONFIG_FSL_USDHC