Patches by Jon Loeliger, 11 May 2004:

(partially, as they contained a lot of crap)

CHANGELOG

@@ -2,7 +2,7 @@
 Changes since U-Boot 1.1.1:
 ======================================================================
 
-* Patches Part 1 by Jon Loeliger, 11 May 2004:
+* Patches by Jon Loeliger, 11 May 2004:
   Dynamically handle REV1 and REV2 MPC85xx parts.
     (Jon Loeliger, 10-May-2004).
   New consistent memory map and Local Access Window across MPC85xx line.

doc/README.mpc85xxads

@@ -13,36 +13,44 @@ use the newest binutils-2.14.tar.bz2 from http://ftp.gnu.org/gnu/binutils.
     shipped with your board. Then apply the following changes:
     SW3[1-6]="all OFF"  (boot from 32bit flash, no boot sequence is used)
     SW10[2-6]="all OFF" (turn on CPM SCC for serial port,works for 8540/8560)
-    SW11[2]='OFF for dracom, ON for draco' (single switch to toggle draco.dracom mode)
+    SW11[2]='OFF for 8560, ON for 8540' (single switch to toggle 8540.8560 mode)
+    SW11[7]='ON' (rev2), 'OFF' (rev1)
     SW4[7-8]="OFF OFF" (enable serial ports,I'm using the top serial connector)
     SW22[1-4]="OFF OFF ON OFF"
     SW5[1-10[="ON ON OFF OFF OFF OFF OFF OFF OFF OFF"
     J1 = "Enable Prog" (Make sure your flash is programmable for development)
-    Ethernet PHY connectors(J47,J56) should be removed if you want to use the ethernet.
+1.2 If you want to test PCI functionality with a 33Mhz PCI card, you will
-1.2 If you want to test PCI functionality with a 33Mhz PCI card, you will have to change
+    have to change the system clock from the default 66Mhz to 33Mhz by
-    the system clock from the default 66Mhz to 33Mhz by  setting SW15[1]="OFF" and
+    setting SW15[1]="OFF" and SW17[8]="OFF". After that you may also need
-    SW17[8]="OFF". After that you may also need double your platform clock(SW6) because
+    double your platform clock(SW6) because the system clock is now only
-    the system clock is now only half of its original value.
+    half of its original value. 
-1.3 SW6 is a very important switch, it decides your platform clock and CPU clock based on
+1.3 SW6 is a very important switch, it decides your platform clock and CPU
-    the on-board system clock(default 66MHz). Check the document along with your board
+    clock based on the on-board system clock(default 66MHz). Check the
-    for details.
+    document along with your board for details.
+
 
 2. MEMORY MAP TO WORK WITH LINUX KERNEL
-2.1. For the initial bringup, we adopted a consistent memory scheme between u-boot and
+
-    linux kernel, you can customize it based on your system requirements:
+2.1. For the initial bringup, we adopted a consistent memory scheme
-      DDR:          0x00000000-0x1fffffff (max 512MB)
+     between u-boot and linux kernel, you can customize it based on your
-      PCI:          0xe0000000-0xefffffff (256MB)
+     system requirements:
-      RIO:          0xf0000000-0xf7ffffff (128MB)
+
-      Local SDRAM:  0xf8000000-0xfbffffff (64MB)
+     0x0000_0000     0x7fff_ffff     DDR                     2G 
-      Local CSx:    0xfc000000-0xfdefffff (31MB) BCSR,RTC,ATM config,etc.
+     0x8000_0000     0x9fff_ffff     PCI MEM                 512M
-      CCSRBAR:      0xfdf00000-0xfdffffff (1MB)
+     0xc000_0000     0xdfff_ffff     Rapid IO                512M
-      Flash:        0xfe000000-0xffffffff (max 32MB)
+     0xe000_0000     0xe000_ffff     CCSR                    1M
-2.2  We are submitting Linux kernel patches for MPC8540 and MPC8560. Hope you will be
+     0xe200_0000     0xe2ff_ffff     PCI IO                  16M
-     able to download them from linuxppc-2.4 public source by the time you are reading
+     0xf000_0000     0xf7ff_ffff     SDRAM                   128M
-     this. Please make sure the kernel's ppcboot.h is consistent with U-Boot's u-boot.h,
+     0xf800_0000     0xf80f_ffff     BCSR                    1M
-     then you can use two default configuration files in the kernel source as a test:
+     0xff00_0000     0xffff_ffff     FLASH (boot bank)       16M
-	arch/ppc/configs/mpc8540ads_defconfig
+
-	arch/ppc/configs/mpc8560ads_defconfig
+2.2 We are submitting Linux kernel patches for MPC8540 and MPC8560. You
+    can download them from linuxppc-2.4 public source. Please make sure the
+    kernel's ppcboot.h is consistent with U-Boot's u-boot.h. You can use two
+    default configuration files as your starting points to configure the
+    kernel:
+	arch/ppc/configs/mpc8540_ads_defconfig
+	arch/ppc/configs/mpc8560_ads_defconfig
 
 3. DEFINITIONS AND COMPILATION
 3.1 Explanation on NEW definitions in include/configs/MPC8540ADS.h and include/
@@ -50,9 +58,6 @@ use the newest binutils-2.14.tar.bz2 from http://ftp.gnu.org/gnu/binutils.
     CONFIG_BOOKE            BOOKE(e.g. Motorola MPC85xx, IBM 440, etc)
     CONFIG_E500             BOOKE e500 family(Motorola)
     CONFIG_MPC85xx          MPC8540,MPC8560 and their derivatives
-    CONFIG_MPC85xx_REV1     MPC85xx Rev 1 Chip, in general you will use a Rev2
-			    chip from Nov.2003. If you still see this definition
-			    while you have a Rev2(and newer) chip,undef this.
     CONFIG_MPC8540          MPC8540 specific
     CONFIG_MPC8560          MPC8560 specific
     CONFIG_MPC8540ADS       MPC8540ADS board specific
@@ -61,8 +66,7 @@ use the newest binutils-2.14.tar.bz2 from http://ftp.gnu.org/gnu/binutils.
     CONFIG_SPD_EEPROM       Use SPD EEPROM for DDR auto configuration, you can also
 			    manual config the DDR after undef this definition.
     CONFIG_DDR_ECC          only for ECC DDR module
-    CONFIG_DDR_DLL          possible DLL fix needed for Rev1 chip for more stability.
+    CONFIG_DDR_DLL          DLL fix on some ADS boards needed for more stability.
-			    you can disable this if you're having a newer chip.
     CONFIG_RAM_AS_FLASH     after define this, you can load U-Boot into localbus
 			    SDRAM and treat localbus SDRAM as a flash. We use this
 			    memory based U-Boot before flash is working while Metrowerks
@@ -78,8 +82,19 @@ use the newest binutils-2.14.tar.bz2 from http://ftp.gnu.org/gnu/binutils.
    make MPC8560ADS_config (or make MPC8540ADS_config)
    make
 
-4.  Note on the 10/100/1000 Ethernet controller:
+4.  Notes:
-4.1 Sometimes after U-Boot is up, the 'tftp' won't work well with TSEC ethernet. If that
+4.1 When connecting with kermit, the following commands must be present.in
+   your .kermrc file. These are especially important when booting as
+   MPC8560, as the serial console will not work without them:
+
+set speed 115200
+set carrier-watch off
+set handshake none
+set flow-control none
+robust
+
+   
+4.2 Sometimes after U-Boot is up, the 'tftp' won't work well with TSEC ethernet. If that
    happens, you can try the following steps to make network work:
    MPC8560ADS>tftp 1000000 pImage
    (if it hangs, use Ctrl-C to quit)
@@ -88,6 +103,17 @@ use the newest binutils-2.14.tar.bz2 from http://ftp.gnu.org/gnu/binutils.
    >1
    >. (to quit this memory operation)
    MPC8560ADS>tftp 1000000 pImage
+4.3 If you're one of the early developers using the Rev1 8540/8560 chips, please use U-Boot 
+   1.0.0, as the newer silicon will only support Rev2 and future revisions of 8540/8560.
+
+
+4.4 Reflash U-boot Image using U-boot
+
+    => tftp 0 u-boot.bin
+    => protect off fff80000 ffffffff
+    => erase fff80000 ffffffff
+    => cp.b 0 fff80000 80000
+
 
 5. Screen dump:
 5.1 MPC8540ADS board

include/asm-ppc/immap_85xx.h

@@ -89,7 +89,13 @@ typedef struct ccsr_ddr {
 	uint	sdram_mode;		/* 0x2118 - DDR SDRAM Mode Configuration */
 	char	res7[8];
 	uint	sdram_interval;		/* 0x2124 - DDR SDRAM Interval Configuration */
+#ifdef MPC85xx_DDR_SDRAM_CLK_CNTL
+	char	res7_5[8];
+	uint	sdram_clk_cntl;		/* 0x2130 - DDR SDRAM Clock Control */
+	char	res8[3276];
+#else
 	char	res8[3288];
+#endif
 	uint	data_err_inject_hi;	/* 0x2e00 - DDR Memory Data Path Error Injection Mask High */
 	uint	data_err_inject_lo;	/* 0x2e04 - DDR Memory Data Path Error Injection Mask Low */
 	uint	ecc_err_inject;		/* 0x2e08 - DDR Memory Data Path Error Injection Mask ECC */
@@ -150,7 +156,7 @@ typedef struct ccsr_i2c {
 	char	res6[4075];
 } ccsr_i2c_t;
 
-#ifdef CONFIG_MPC8540
+#if defined (CONFIG_MPC8540) || defined (CONFIG_MPC8555)
 /* DUART Registers(0x4000-0x5000) */
 typedef struct ccsr_duart {
 	char	res1[1280];
@@ -1015,7 +1021,7 @@ typedef struct ccsr_pic {
 } ccsr_pic_t;
 
 /* CPM Block(0x8_0000-0xc_0000) */
-#ifdef CONFIG_MPC8540
+#if defined (CONFIG_MPC8540) || defined (CONFIG_MPC8555)
 typedef struct ccsr_cpm {
 	char res[262144];
 } ccsr_cpm_t;

include/asm-ppc/u-boot.h

@@ -83,6 +83,7 @@ typedef struct bd_info {
     defined(CONFIG_SXNI855T)		|| \
     defined(CONFIG_SVM_SC8xx)		|| \
     defined(CONFIG_MPC8540ADS)          || \
+    defined(CONFIG_MPC8555CDS)		|| \
     defined(CONFIG_MPC8560ADS)		|| \
     defined(CONFIG_440_GX)
 	/* second onboard ethernet port */
@@ -90,7 +91,7 @@ typedef struct bd_info {
 #endif
 #if defined(CFG_GT_6426x) || defined(CONFIG_SVM_SC8xx) || \
     defined(CONFIG_MPC8540ADS) || defined(CONFIG_MPC8560ADS) || \
-    defined(CONFIG_440_GX)
+    defined(CONFIG_MPC8555CDS) || defined(CONFIG_440_GX)
 	/* third onboard ethernet port */
 	unsigned char	bi_enet2addr[6];
 #endif

include/common.h

@@ -316,6 +316,7 @@ uint	get_immr      (uint);
 #endif
 uint	get_pir	      (void);
 uint	get_pvr	      (void);
+uint	get_svr	      (void);
 uint	rd_ic_cst     (void);
 void	wr_ic_cst     (uint);
 void	wr_ic_adr     (uint);