board: stm32: Add Engicam i.Core STM32MP1 C.TOUCH 2.0

Engicam C.TOUCH 2.0 is an EDIMM compliant general purpose Carrier
board.

Genaral features:
- Ethernet 10/100
- Wifi/BT
- USB Type A/OTG
- Audio Out
- CAN
- LVDS panel connector

i.Core STM32MP1 is an EDIMM SoM based on STM32MP157A from Engicam.

i.Core STM32MP1 needs to mount on top of this Carrier board for
creating complete i.Core STM32MP1 C.TOUCH 2.0 board.

Linux dts commit details:

commit <6ca2898df59f> ("ARM: dts: stm32: Add Engicam i.Core STM32MP1
C.TOUCH 2.0")

Add support for it.

Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

arch/arm/dts/Makefile

@@ -989,6 +989,7 @@ dtb-$(CONFIG_ARCH_STI) += stih410-b2260.dtb
 dtb-$(CONFIG_STM32MP15x) += \
 	stm32mp157a-dk1.dtb \
 	stm32mp157a-avenger96.dtb \
+	stm32mp157a-icore-stm32mp1-ctouch2.dtb \
 	stm32mp157a-icore-stm32mp1-edimm2.2.dtb \
 	stm32mp157c-dk2.dtb \
 	stm32mp157c-ed1.dtb \

arch/arm/dts/stm32mp157a-icore-stm32mp1-ctouch2-u-boot.dtsi

@@ -0,0 +1,51 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2019 - All Rights Reserved
+ * Copyright (c) 2020 Amarula Solutions(India)
+ * Author: Jagan Teki <jagan@amarulasolutions.com>
+ */
+
+#include "stm32mp157a-icore-stm32mp1-u-boot.dtsi"
+
+/{
+	aliases {
+		mmc0 = &sdmmc1;
+	};
+
+	chosen {
+		stdout-path = &uart4;
+	};
+};
+
+&sdmmc1 {
+	u-boot,dm-pre-reloc;
+};
+
+&sdmmc1_b4_pins_a {
+	u-boot,dm-pre-reloc;
+
+	pins1 {
+		u-boot,dm-pre-reloc;
+	};
+
+	pins2 {
+		u-boot,dm-pre-reloc;
+	};
+};
+
+&uart4 {
+	u-boot,dm-pre-reloc;
+};
+
+&uart4_pins_a {
+	u-boot,dm-pre-reloc;
+
+	pins1 {
+		u-boot,dm-pre-reloc;
+	};
+
+	pins2 {
+		u-boot,dm-pre-reloc;
+		bias-pull-up;
+	};
+};

arch/arm/dts/stm32mp157a-icore-stm32mp1-ctouch2.dts

@@ -0,0 +1,47 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (c) STMicroelectronics 2019 - All Rights Reserved
+ * Copyright (c) 2020 Engicam srl
+ * Copyright (c) 2020 Amarula Solutons(India)
+ */
+
+/dts-v1/;
+#include "stm32mp157.dtsi"
+#include "stm32mp157a-icore-stm32mp1.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxaa-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Engicam i.Core STM32MP1 C.TOUCH 2.0";
+	compatible = "engicam,icore-stm32mp1-ctouch2",
+		     "engicam,icore-stm32mp1", "st,stm32mp157";
+
+	aliases {
+		serial0 = &uart4;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&sdmmc1 {
+	bus-width = <4>;
+	disable-wp;
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	st,neg-edge;
+	vmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&uart4_pins_a>;
+	pinctrl-1 = <&uart4_sleep_pins_a>;
+	pinctrl-2 = <&uart4_idle_pins_a>;
+	status = "okay";
+};

arch/arm/mach-stm32mp/Kconfig

@@ -96,6 +96,11 @@ config TARGET_ICORE_STM32MP1
 	  * i.Core STM32MP1 needs to mount on top of EDIMM2.2 for
 	    creating complete i.Core STM32MP1 EDIMM2.2 Starter Kit.
 
+	  i.Core STM32MP1 C.TOUCH 2.0
+	  * C.TOUCH 2.0 is a general purpose Carrier board.
+	  * i.Core STM32MP1 needs to mount on top of this Carrier board
+	    for creating complete i.Core STM32MP1 C.TOUCH 2.0 board.
+
 config TARGET_DH_STM32MP1_PDK2
 	bool "DH STM32MP1 PDK2"
 	select STM32MP15x

board/engicam/stm32mp1/MAINTAINERS

@@ -1,3 +1,9 @@
+i.Core-STM32MP1-CTOUCH2.0
+M:	Jagan Teki <jagan@amarulasolutions.com>
+M:	Matteo Lisi <matteo.lisi@engicam.com>
+S:	Maintained
+F:	configs/stm32mp15-icore-stm32mp1-ctouch2_defconfig
+
 i.Core-STM32MP1-EDIMM2.2
 M:	Jagan Teki <jagan@amarulasolutions.com>
 M:	Matteo Lisi <matteo.lisi@engicam.com>

configs/stm32mp15-icore-stm32mp1-ctouch2_defconfig

@@ -0,0 +1,79 @@
+CONFIG_ARM=y
+CONFIG_ARCH_STM32MP=y
+CONFIG_SYS_MALLOC_F_LEN=0x3000
+CONFIG_SYS_MEMTEST_START=0xc0000000
+CONFIG_SYS_MEMTEST_END=0xc4000000
+CONFIG_ENV_OFFSET=0x280000
+CONFIG_SPL_TEXT_BASE=0x2FFC2500
+CONFIG_SPL_MMC_SUPPORT=y
+CONFIG_SPL=y
+CONFIG_TARGET_ICORE_STM32MP1=y
+CONFIG_ENV_OFFSET_REDUND=0x2C0000
+# CONFIG_ARMV7_VIRT is not set
+CONFIG_DEFAULT_DEVICE_TREE="stm32mp157a-icore-stm32mp1-ctouch2"
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_FIT=y
+CONFIG_BOOTCOMMAND="run bootcmd_stm32mp"
+CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION=y
+CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION=3
+CONFIG_SPL_ENV_SUPPORT=y
+CONFIG_SPL_I2C_SUPPORT=y
+CONFIG_SPL_POWER_SUPPORT=y
+CONFIG_SYS_PROMPT="STM32MP> "
+CONFIG_CMD_ADTIMG=y
+CONFIG_CMD_ERASEENV=y
+CONFIG_CMD_MEMINFO=y
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_ADC=y
+CONFIG_CMD_CLK=y
+CONFIG_CMD_FUSE=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_REMOTEPROC=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_TIME=y
+CONFIG_CMD_TIMER=y
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
+CONFIG_CMD_EXT4_WRITE=y
+# CONFIG_SPL_DOS_PARTITION is not set
+CONFIG_OF_SPL_REMOVE_PROPS="interrupts interrupt-names interrupts-extended interrupt-controller \\\#interrupt-cells interrupt-parent dmas dma-names assigned-clocks assigned-clock-rates assigned-clock-parents hwlocks"
+CONFIG_ENV_IS_NOWHERE=y
+CONFIG_ENV_IS_IN_MMC=y
+CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+# CONFIG_SPL_ENV_IS_NOWHERE is not set
+CONFIG_DM_HWSPINLOCK=y
+CONFIG_HWSPINLOCK_STM32=y
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_STM32F7=y
+CONFIG_LED=y
+CONFIG_LED_GPIO=y
+CONFIG_DM_MAILBOX=y
+CONFIG_STM32_IPCC=y
+CONFIG_STM32_FMC2_EBI=y
+CONFIG_DM_MMC=y
+CONFIG_SUPPORT_EMMC_BOOT=y
+CONFIG_STM32_SDMMC2=y
+CONFIG_PHY_REALTEK=y
+CONFIG_DM_ETH=y
+CONFIG_DWC_ETH_QOS=y
+CONFIG_PHY=y
+CONFIG_PINCONF=y
+# CONFIG_SPL_PINCTRL_FULL is not set
+CONFIG_PINCTRL_STMFX=y
+CONFIG_DM_PMIC=y
+# CONFIG_SPL_PMIC_CHILDREN is not set
+CONFIG_PMIC_STPMIC1=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
+CONFIG_REMOTEPROC_STM32_COPRO=y
+CONFIG_DM_RTC=y
+CONFIG_RTC_STM32=y
+CONFIG_SERIAL_RX_BUFFER=y
+CONFIG_WDT=y
+CONFIG_WDT_STM32MP=y
+CONFIG_LZO=y
+CONFIG_ERRNO_STR=y