Updates configs/am43xx_evm.h to use CONFIG options from
SOC specific Kconfig file for various calculations.
On AM43x devices, the address of SPL entry point depends on
the device type, i.e. whether it is secure or non-secure.
Further, for non-secure devices, the SPL entry point is different
between USB HOST boot mode, other "memory" boot modes (MMC, NAND)
and "peripheral" boot modes (UART, USB)
To add to the complexity, on secure devices, in addition to the
above differences, the SPL entry point can change because of the
space occupied by other components (other than u-boot or spl)
that go into a secure boot image.
To prevent the user from having to modify source files every time
any component of the secure image changes, the value of
CONFIG_SPL_TEXT_BASE has been set using a Kconfig option that
is supplied in the am43xx_*_defconfig files
Using the CONFIG options also enables us to do away with some
compile time flags that were used to specify CONFIG_SPL_TEXT_BASE
for different boot modes.
On QSPI devices, the same problem described above occurs w.r.t. the
address of the u-boot entry point in flash, when booting secure
devices. To handle this, CONFIG_SYS_TEXT_BASE is also setup via
a Kconfig option and the defconfig files.
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Daniel Allred <d-allred@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Adding support for AM43xx secure devices require the addition
of some SOC specific config options like the amount of memory
used by public ROM and the address of the entry point of u-boot
or SPL, as seen by the ROM code, for the image to be built
correctly.
This mandates the addition of am AM43xx CONFIG option and the
ARM Kconfig file has been modified to source this SOC Kconfig
file. Moving the TARGET_AM43XX_EVM config option to the SOC
KConfig and out of the arch/arm/Kconfig.
Updating defconfigs to add the CONFIG_AM43XX=y statement and
removing the #define CONFIG_AM43XX from the header file.
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Daniel Allred <d-allred@ti.com>
Tested-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This option is always enabled and is about to be removed. Drop references
to it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
It is well past the deadline for conversion to generic board init. Remove
the old code.
Stefan, can you test this please and perhaps send a follow-up patch if needed?
Signed-off-by: Simon Glass <sjg@chromium.org>
Some hardware that is supported by U-Boot can not handle DMA above 32bits.
For these systems, we need to come up with a way to expose the disk interface
in a safe way.
This patch implements EFI specific bounce buffers. For non-EFI cases, this
apparently was no issue so far, since we can just define our environment
variables conveniently.
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds platform code for the Amlogic Meson GXBaby (S905) SoC and a
board definition for ODROID-C2. This initial submission only supports
UART and Ethernet (through the existing Designware driver). DTS files
are the ones submitted to Linux arm-soc for 4.7 [1].
[1] https://patchwork.ozlabs.org/patch/603583/
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that we can expose network functionality to EFI applications,
the logical next step is to load them via pxe to execute them as
well.
This patch adds the necessary bits to the distro script to automatically
load and execute EFI payloads. It identifies the dhcp client as a uEFI
capable PXE client, hoping the server returns a tftp path to a workable
EFI binary that we can then execute.
To enable boards that don't come with a working device tree preloaded,
this patch also adds support to load a device tree from the /dtb directory
on the remote tftp server.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
There are client identifiers specifically reserved for ARM U-Boot
according to http://www.ietf.org/assignments/dhcpv6-parameters/dhcpv6-parameters.xml#processor-architecture.
So let's actually make use of them rather than the bogus 0x100 that
we emitted so far.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Drop the Xilinx define to 0x100 as it's not the correct value to
use].
Signed-off-by: Tom Rini <trini@konsulko.com>
This code does not currently build with driver model enabled for block
devices. Update it to correct this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexander Graf <agraf@suse.de>
We have a bunch of boards that define their vendor class identifier and
client archs in the board files or in the distro config. Move everything
to the generic Kconfig options.
We're missing the distinction between i386 and x86_64, as I couldn't find
any config variable that would tell us the difference. Is that really important
to people? I guess not, so I left it out.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
We can now successfully boot EFI applications from disk, but users
may want to also run them from a PXE setup.
This patch implements rudimentary network support, allowing a payload
to send and receive network packets.
With this patch, I was able to successfully run grub2 with network
access inside of QEMU's -M xlnx-ep108.
Signed-off-by: Alexander Graf <agraf@suse.de>
This shows a proper progress display and the total amount of data
transferred. Enable it for Raspberry Pi.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
A mailbox is a hardware mechanism for transferring small message and/or
notifications between the CPU on which U-Boot runs and some other device
such as an auxilliary CPU running firmware or a hardware module.
This patch defines a standard API that connects mailbox clients to mailbox
providers (drivers). Initially, DT is the only supported method for
connecting the two.
The DT binding specification (mailbox.txt) was taken from Linux kernel
v4.5's Documentation/devicetree/bindings/mailbox/mailbox.txt.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
The current reset API implements a method to reset the entire system.
In the near future, I'd like to introduce code that implements the device
tree reset bindings; i.e. the equivalent of the Linux kernel's reset API.
This controls resets to individual HW blocks or external chips with reset
signals. It doesn't make sense to merge the two APIs into one since they
have different semantic purposes. Resolve the naming conflict by renaming
the existing reset API to sysreset instead, so the new reset API can be
called just reset.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
This will allow a driver's bind function to use the driver data. One
example is the Tegra186 GPIO driver, which instantiates child devices
for each of its GPIO ports, yet supports two different HW instances each
with a different set of ports, and identified by the udevice_id .data
field.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
The exynos5 platforms use DM in U-Boot and do not use DM in SPL. The serial
driver, serial_s5p.c, is DM-only. This is OK for U-Boot, but in SPL, this
will fail with the following compile error:
drivers/built-in.o: In function `get_current':
...u-boot/drivers/serial/serial.c:387: undefined reference to `default_serial_console'
This warning happens because common/console.c is compiled into U-Boot SPL
if CONFIG_SPL_SERIAL_SUPPORT . The common/console.c invokes serial_*()
functions and since exynos5 does not use DM in SPL, these functions come
from drivers/serial/serial.c . The serial_*() locate default serial port
by calling default_serial_console(), but because the serial_s5p.c is DM-only,
it does no longer define default_serial_console(). Thus the error.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Move CONFIG_SYS_TEXT_BASE to Kconfig, and add default values in board
Kconfig files matching what was present in their config headers. This
will make it cleaner to conditionalise the value for Malta based on 32
vs 64 bit builds.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Make use of device model & device tree to probe the UART driver. This is
the initial step in bringing Malta up to date with driver model, and
allows for cleaner handling of the different I/O addresses for different
system controllers by specifying the ISA bus address instead of a
translated memory address.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The address of the UART differs based upon the system controller because
it's actually within the I/O port region, which is in a different
location for each system controller. Rather than handling this as 2
UARTs with the correct one selected at runtime, use I/O port accessors
for the UART such that access to it gets translated into the I/O port
region automatically.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
As arm64 has slightly different expectations about load addresses, lets
use a different set of default addresses for things like the kernel.
As arm64 kernels don't come with a decompressor right now, reserve some
more space for really big uncompressed kernels.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The current SPL header, created by the 'mksunxiboot' tool, has size
32 bytes. But the code in the boot ROM stores the information about
the boot media at the offset 0x28 before passing control to the SPL.
For example, when booting from the SD card, the magic number written
by the boot ROM is 0. And when booting from the SPI flash, the magic
number is 3. NAND and eMMC probably have their own special magic
numbers too.
Currently the corrupted byte is a part of one of the instructions in
the reset vectors table:
b reset
ldr pc, _undefined_instruction
ldr pc, _software_interrupt <- Corruption happens here
ldr pc, _prefetch_abort
ldr pc, _data_abort
ldr pc, _not_used
ldr pc, _irq
ldr pc, _fiq
In practice this does not cause any visible problems, but it's still
better to fix it. As a bonus, the reported boot media type can be
later used in the 'spl_boot_device' function, but this is out of
the scope of this patch.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The A80 uses the AXP809 as its primary PMIC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Adds poweroff support for axp818 pmic.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The AXP818 has a switchable output, SW. This is commonly used for
controlling power to the LCD backlight.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Update several boards to use driver model for video. This involves changes
to the EDP and FIMD (frame buffer) drivers. Existing PWM, simple-panel and
pwm-backlight drivers are used. These work without additional configuration
since they use the device tree settings in the same way as Linux.
Boards converted are:
- snow
- spring
- peach-pit
- peach-pi
All have been tested. Not converted:
- MIPI display driver
- s5pc210_universal
- smdk5420
- smdk5250
- trats
- trats2
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Use 'priv' for a private pointer and 'regs' for a register pointer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
These are used by peach_pit and peach_pi. Add them so they can be referenced
in the device tree files.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Some boards have the LCD enabled but I cannot test operation for the driver
model conversion. Disable the LCD on these to avoid build errors.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This file currently requires an LCD. Adjust it to work without one.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This is used for video signals in some drivers so provide a standard way
of representing it in an enum.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Put the pointer to this structure in struct vidinfo so that we can
reference it without it being global.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Drop these and use parameters instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
We always use device tree with video, so can drop these #ifdefs. Some of the
hardware addresses are not needed either.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add support for Exynos7420 SoC. The Exynos7420 SoC has four Cortex-A57
and four Cortex-A53 CPUs and includes various peripheral controllers.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add a clock driver for Exynos7420 SoC. There are about 25 clock controller
blocks in Exynos7420 out of which support for topc, top0 and peric1 blocks
are added in this initial version of the driver.
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add a helper to phy.h to identify whether the
phy is configured for SGMII all variables.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Move the phy_interface_is_rgmii to the phy.h
file for all phy's to be able to use the API.
This now aligns with the Linux kernel based on
commit e463d88c36d42211aa72ed76d32fb8bf37820ef1
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add the device tree bindings and the accompanying documentation
for the TI DP83867 Giga bit ethernet phy driver.
The original document was from:
[commit 2a10154abcb75ad0d7b6bfea6210ac743ec60897 from the Linux kernel]
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
