GitHub-Mirror/u-boot
2
0
Fork 0
mirror of https://github.com/Fishwaldo/u-boot.git synced 2025-03-22 07:01:39 +00:00
Code Issues Projects Releases Packages Wiki Activity Actions
u-boot/board/atmel/at91sam9263ek/at91sam9263ek.c
Andreas Henriksson 81724e09a0 at91sam9263ek: add mmc support 
Add support for using the Atmel MCI driver on at91sam9263ek.
This change is modeled after the existing at91sam9260ek support.

Please note that this hooks up slot1 (MCI1) for SD. Not both.

Tested with at91bootstrap and u-boot on dataflash in slot 0
and fat-formatted 8GB SDHC in slot 1 on first revision
at91sam9263ek (which must use dataflash in slot0 to boot).

CONFIG_ATMEL_MCI_PORTB not tested.

Signed-off-by: Andreas Henriksson <andreas.henriksson@endian.se>
[remove empty line]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-03-09 18:24:52 +01:00

287 lines
6.9 KiB
C
Raw Blame History

/*
* (C) Copyright 2007-2008
* Stelian Pop <stelian@popies.net>
* Lead Tech Design <www.leadtechdesign.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <asm/sizes.h>
#include <asm/arch/at91sam9263.h>
#include <asm/arch/at91sam9_smc.h>
#include <asm/arch/at91_common.h>
#include <asm/arch/at91_pmc.h>
#include <asm/arch/at91_matrix.h>
#include <asm/arch/at91_pio.h>
#include <asm/arch/clk.h>
#include <asm/io.h>
#include <asm/arch/gpio.h>
#include <asm/arch/hardware.h>
#include <lcd.h>
#include <atmel_lcdc.h>
#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB)
#include <net.h>
#endif
#include <netdev.h>
#include <atmel_mci.h>
DECLARE_GLOBAL_DATA_PTR;
/* ------------------------------------------------------------------------- */
/*
* Miscelaneous platform dependent initialisations
*/
#ifdef CONFIG_CMD_NAND
static void at91sam9263ek_nand_hw_init(void)
{
unsigned long csa;
at91_smc_t *smc = (at91_smc_t *) ATMEL_BASE_SMC0;
at91_matrix_t *matrix = (at91_matrix_t *) ATMEL_BASE_MATRIX;
at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC;
/* Enable CS3 */
csa = readl(&matrix->csa[0]) | AT91_MATRIX_CSA_EBI_CS3A;
writel(csa, &matrix->csa[0]);
/* Enable CS3 */
/* Configure SMC CS3 for NAND/SmartMedia */
writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0),
&smc->cs[3].setup);
writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(3) |
AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(3),
&smc->cs[3].pulse);
writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5),
&smc->cs[3].cycle);
writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
AT91_SMC_MODE_EXNW_DISABLE |
#ifdef CONFIG_SYS_NAND_DBW_16
AT91_SMC_MODE_DBW_16 |
#else /* CONFIG_SYS_NAND_DBW_8 */
AT91_SMC_MODE_DBW_8 |
#endif
AT91_SMC_MODE_TDF_CYCLE(2),
&smc->cs[3].mode);
writel(1 << ATMEL_ID_PIOA | 1 << ATMEL_ID_PIOCDE,
&pmc->pcer);
/* Configure RDY/BSY */
at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1);
/* Enable NandFlash */
at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
}
#endif
#ifdef CONFIG_MACB
static void at91sam9263ek_macb_hw_init(void)
{
at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC;
at91_pio_t *pio = (at91_pio_t *) ATMEL_BASE_PIO;
/* Enable clock */
writel(1 << ATMEL_ID_EMAC, &pmc->pcer);
/*
* Disable pull-up on:
* RXDV (PC25) => PHY normal mode (not Test mode)
* ERX0 (PE25) => PHY ADDR0
* ERX1 (PE26) => PHY ADDR1 => PHYADDR = 0x0
*
* PHY has internal pull-down
*/
writel(1 << 25, &pio->pioc.pudr);
writel((1 << 25) | (1 <<26), &pio->pioe.pudr);
at91_phy_reset();
/* Re-enable pull-up */
writel(1 << 25, &pio->pioc.puer);
writel((1 << 25) | (1 <<26), &pio->pioe.puer);
at91_macb_hw_init();
}
#endif
#ifdef CONFIG_LCD
vidinfo_t panel_info = {
vl_col: 240,
vl_row: 320,
vl_clk: 4965000,
vl_sync: ATMEL_LCDC_INVLINE_INVERTED |
ATMEL_LCDC_INVFRAME_INVERTED,
vl_bpix: 3,
vl_tft: 1,
vl_hsync_len: 5,
vl_left_margin: 1,
vl_right_margin:33,
vl_vsync_len: 1,
vl_upper_margin:1,
vl_lower_margin:0,
mmio: ATMEL_BASE_LCDC,
};
void lcd_enable(void)
{
at91_set_pio_value(AT91_PIO_PORTA, 30, 1); /* power up */
}
void lcd_disable(void)
{
at91_set_pio_value(AT91_PIO_PORTA, 30, 0); /* power down */
}
static void at91sam9263ek_lcd_hw_init(void)
{
at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC;
at91_set_a_periph(AT91_PIO_PORTC, 1, 0); /* LCDHSYNC */
at91_set_a_periph(AT91_PIO_PORTC, 2, 0); /* LCDDOTCK */
at91_set_a_periph(AT91_PIO_PORTC, 3, 0); /* LCDDEN */
at91_set_b_periph(AT91_PIO_PORTB, 9, 0); /* LCDCC */
at91_set_a_periph(AT91_PIO_PORTC, 6, 0); /* LCDD2 */
at91_set_a_periph(AT91_PIO_PORTC, 7, 0); /* LCDD3 */
at91_set_a_periph(AT91_PIO_PORTC, 8, 0); /* LCDD4 */
at91_set_a_periph(AT91_PIO_PORTC, 9, 0); /* LCDD5 */
at91_set_a_periph(AT91_PIO_PORTC, 10, 0); /* LCDD6 */
at91_set_a_periph(AT91_PIO_PORTC, 11, 0); /* LCDD7 */
at91_set_a_periph(AT91_PIO_PORTC, 14, 0); /* LCDD10 */
at91_set_a_periph(AT91_PIO_PORTC, 15, 0); /* LCDD11 */
at91_set_a_periph(AT91_PIO_PORTC, 16, 0); /* LCDD12 */
at91_set_b_periph(AT91_PIO_PORTC, 12, 0); /* LCDD13 */
at91_set_a_periph(AT91_PIO_PORTC, 18, 0); /* LCDD14 */
at91_set_a_periph(AT91_PIO_PORTC, 19, 0); /* LCDD15 */
at91_set_a_periph(AT91_PIO_PORTC, 22, 0); /* LCDD18 */
at91_set_a_periph(AT91_PIO_PORTC, 23, 0); /* LCDD19 */
at91_set_a_periph(AT91_PIO_PORTC, 24, 0); /* LCDD20 */
at91_set_b_periph(AT91_PIO_PORTC, 17, 0); /* LCDD21 */
at91_set_a_periph(AT91_PIO_PORTC, 26, 0); /* LCDD22 */
at91_set_a_periph(AT91_PIO_PORTC, 27, 0); /* LCDD23 */
writel(1 << ATMEL_ID_LCDC, &pmc->pcer);
gd->fb_base = ATMEL_BASE_SRAM0;
}
#ifdef CONFIG_LCD_INFO
#include <nand.h>
#include <version.h>
#ifndef CONFIG_SYS_NO_FLASH
extern flash_info_t flash_info[];
#endif
void lcd_show_board_info(void)
{
ulong dram_size, nand_size;
#ifndef CONFIG_SYS_NO_FLASH
ulong flash_size;
#endif
int i;
char temp[32];
lcd_printf ("%s\n", U_BOOT_VERSION);
lcd_printf ("(C) 2008 ATMEL Corp\n");
lcd_printf ("at91support@atmel.com\n");
lcd_printf ("%s CPU at %s MHz\n",
ATMEL_CPU_NAME,
strmhz(temp, get_cpu_clk_rate()));
dram_size = 0;
for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++)
dram_size += gd->bd->bi_dram[i].size;
nand_size = 0;
for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++)
nand_size += nand_info[i].size;
#ifndef CONFIG_SYS_NO_FLASH
flash_size = 0;
for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i++)
flash_size += flash_info[i].size;
#endif
lcd_printf (" %ld MB SDRAM, %ld MB NAND",
dram_size >> 20,
nand_size >> 20 );
#ifndef CONFIG_SYS_NO_FLASH
lcd_printf (",\n %ld MB NOR",
flash_size >> 20);
#endif
lcd_puts ("\n");
}
#endif /* CONFIG_LCD_INFO */
#endif
#ifdef CONFIG_GENERIC_ATMEL_MCI
int board_mmc_init(bd_t *bd)
{
at91_mci_hw_init();
return atmel_mci_init((void *)ATMEL_BASE_MCI1);
}
#endif
int board_early_init_f(void)
{
struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
/* Enable clocks for all PIOs */
writel((1 << ATMEL_ID_PIOA) | (1 << ATMEL_ID_PIOB) |
(1 << ATMEL_ID_PIOCDE),
&pmc->pcer);
at91_seriald_hw_init();
return 0;
}
int board_init(void)
{
/* arch number of AT91SAM9263EK-Board */
gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9263EK;
/* adress of boot parameters */
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
#ifdef CONFIG_CMD_NAND
at91sam9263ek_nand_hw_init();
#endif
#ifdef CONFIG_HAS_DATAFLASH
at91_set_pio_output(AT91_PIO_PORTE, 20, 1); /* select spi0 clock */
at91_spi0_hw_init(1 << 0);
#endif
#ifdef CONFIG_MACB
at91sam9263ek_macb_hw_init();
#endif
#ifdef CONFIG_USB_OHCI_NEW
at91_uhp_hw_init();
#endif
#ifdef CONFIG_LCD
at91sam9263ek_lcd_hw_init();
#endif
return 0;
}
int dram_init(void)
{
gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
CONFIG_SYS_SDRAM_SIZE);
return 0;
}
#ifdef CONFIG_RESET_PHY_R
void reset_phy(void)
{
}
#endif
int board_eth_init(bd_t *bis)
{
int rc = 0;
#ifdef CONFIG_MACB
rc = macb_eth_initialize(0, (void *) ATMEL_BASE_EMAC, 0x00);
#endif
return rc;
}
Reference in a new issue View git blame Copy permalink