* Sunvell R69: cpu voltage regulator (re-)added - dram clock reduced.
CPU regulator (re-)added to u-boot and kernel dts - the box will not boot without it.
Dram clock reduced in defconfig to increase stability.
[AR-85]
* Updated rockchip64-dev to u-boot v2019.10 and BL31 v1.30 (rk3399 boards)
* Updated rk3399 to u-boot v2019.10 and BL31 v1.30
* Revert changes to renegade u-boot patches
* Moved renegade u-boot patches into board dir
* Added debug info for RockPro64 and switched sdmmc to fifo-mode
* Disabled regulators in SPL for RockPro64
* Re-enabled sd vcc regulator in SPL for RockPro64
* Some device tree and config changes for OrangePi RK3399
* Fixed Rock Pi 4A's $BOOTCONFIG
* Let some boards use mainline atf instead of the one in rkbin
For example, roc-rk3399-pc can just boot the kernel using the
mainline atf.
* Add roc-rk3399-pc
* Fixed reset in mainline ATF
* Attached ATF version to v2.2 tag
* WIP: sdmmc fifo-mode in SPL only
* Renamed source config files
* Reverted changes to rockchip64 sources config
* Reverted patch moves
* Add missing trust.ini patch to rk3399 u-boot
* Reinstated tpl/spl patches in rk3399 family
* Added $RKBIN_DIR prefix in rk3399 sources
* Add demonstration of boards bootloader assignment in rk3399
AR-1 - Adding support category for distributions
AR-4 - Remove Allwinner legacy
AR-5 - Drop Udoo family and move Udoo board into newly created imx6 family
AR-9 - Rename sunxi-next to sunxi-legacy
AR-10 - Rename sunxi-dev to sunxi-current
AR-11 - Adding Radxa Rockpi S support
AR-13 - Rename rockchip64-default to rockchip64-legacy
AR-14 - Add rockchip64-current as mainline source
AR-15 - Drop Rockchip 4.19.y NEXT, current become 5.3.y
AR-16 - Rename RK3399 default to legacy
AR-17 - Rename Odroid XU4 next and default to legacy 4.14.y, add DEV 5.4.y
AR-18 - Add Odroid N2 current mainline
AR-19 - Move Odroid C1 to meson family
AR-20 - Rename mvebu64-default to mvebu64-legacy
AR-21 - Rename mvebu-default to mvebu-legacy
AR-22 - Rename mvebu-next to mvebu-current
AR-23 - Drop meson64 default and next, current becomes former DEV 5.3.y
AR-24 - Drop cubox family and move Cubox/Hummingboard boards under imx6
AR-26 - Adjust motd
AR-27 - Enabling distribution release status
AR-28 - Added new GCC compilers
AR-29 - Implementing Ubuntu Eoan
AR-30 - Add desktop packages per board or family
AR-31 - Remove (Ubuntu/Debian) distribution name from image filename
AR-32 - Move arch configs from configuration.sh to separate arm64 and armhf config files
AR-33 - Revision numbers for beta builds changed to day_in_the_year
AR-34 - Patches support linked patches
AR-35 - Break meson64 family into gxbb and gxl
AR-36 - Add Nanopineo2 Black
AR-38 - Upgrade option from old branches to new one via armbian-config
AR-41 - Show full timezone info
AR-43 - Merge Odroid N2 to meson64
AR-44 - Enable FORCE_BOOTSCRIPT_UPDATE for all builds
* Fix wifi
patch "board-h2plus-nanopi-duo-add-device.patch": increase post-power-on-delay-ms from 50ms to 200ms in wifi_pwrseq node in nanopi-duo dts [dev-branch].
Change in line with other XRADIO device trees (orange pi zero, sunvell).
See also Pull Request #1605.
* Fix xradio patch (dev-branch)
fix KConfig to 5.x - WLAN_VENDOR-flag set to "y" in line with other drivers - otherwise module not loaded.
* correct device name
change nodes "model" and "compatible" to correct device name (from "NanoPi Duo AIR" to "NanoPi Duo") [dev-branch]
Not functionally necessary, but more correct.
* Initial commit for serial consoles rfc
* Board configuration cleanup + small tweaks
* Add serial gadget rename to dev kernel as well
* Cleanup, fixing permissions
* Cleanup board configs
* Initial commit for FA ZeroPi.
* Tested for building.
* Adjust few bugs.
* Move to WIP since its not tested on hardware yet.
Signed-off-by: Igor Pecovnik <igor.pecovnik@gmail.com>
* Added initial support of MCIMX7SABRE board
MCIMX7SABRE is NXP iMX7d-based board with 1Gb RAM
2xGBE, 1xmPCIe
Change-Id: I62685a55de54fa6109bef2a8e2ee760d831ffa0e
* Added initial support of MCIMX7SABRE board
MCIMX7SABRE is NXP iMX7d-based board with 1Gb RAM
2xGBE, 1xmPCIe
Change-Id: I62685a55de54fa6109bef2a8e2ee760d831ffa0e
* Changed BOARDFAMILY from mx7dsabre to imx7d
Change-Id: Id351c9f6a8c907b415b804bfe11b86027278ed86
* Disabled MD driver for imx7d Kernel
MD driver does not work correctly on NXP-modified kernel
Change-Id: I58e8de6ee0b99282c452f594e22f6f7e1ff59ae0
* Added ALSA configuration bits for rk3288 HDMI and SPDIF to allow
pulseaudio show proper sound device/profile/mapping names instead of
just "Built-in Audio" for all of them
* Added ALSA device description in asound.conf to provide correct labels for PulseAudio for RK3288 devices when SPDIF and DW-I2S-HDMI simple audio cards are exposed
Removed unnecessary ALSA configuration files previously added from rockchip.conf
* Fixed cpu operating points tables and raised a bit (+5°C) cooling for non-critical temperatures for xt-q8l-v10 in dev and next kernel flavours
* Fixed again cpu opp table
* Removed whole cpu opp table and retouch only necessary operating points
* Enabled gpiomem driver for xt-q8l-v10 in next kernel flavour
* Added debounce delay and card detect gpio pins for sdmmc card holder for xt-q8l-v10 board
* Added card-detect and debounce delay for sdmmc for xt-q8l-v10 board in next kernel flavour too
* Fixed missing comment in xt-q8l-v10 device tree patch
* Added gpiomem to xt-q8l-v10 board for dev kernel
* Fixed FAN53555/Silergy patches to accomodate changes in u-boot v2019.04
* Changed property property flags for USB regulators in u-boot and kernel: kernel is now informed that bootloader is going to turn the USB power on
* Removed assert-phy-reset-when-waking-up-in-rk3288-platform patch due to inclusion in mainline 5.2 kernel
Reenabled ARM-DTSI-rk3288-add-usbphy-reset patch to include USB PHY reset lines to all rk3288 devices
* Removed ARM-DTSI-rk3288-add-usbphy-reset.patch due to inclusion in mainline kernel 5.2
* Initial Mvebu RFC https://github.com/armbian/build/issues/1426
Signed-off-by: Igor Pecovnik <igor.pecovnik@gmail.com>
* mvebu: add missing patches
Signed-off-by: Igor Pecovnik <igor.pecovnik@gmail.com>
* mvebu: change making u-boot targets to standard way, adjust patches and config
Signed-off-by: Igor Pecovnik <igor.pecovnik@gmail.com>
* helios4: set default branch to use U-Boot 2018.11
Switch over to U-Boot 2018.11 that has been used for some time in next
branch.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* mvebu: helios4: Enable DEV branch
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* u-boot: Add RTC support on Clearfog and Helios4
Added DM driver for mvebu RTC and enable it on Clearfog and Helios4
configuration.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* add boot-marvell.cmd backward compatibility
The patches added missing variable that used on boot-marvell.cmd and
also adjust the some memory addresses to prevent crash due to usage of
fdt_high and initrd_high.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* helios4: Added SPI NOR flash target
Build bootable SPI NOR flash image.
Change the boot order to USB -> SATA -> MMC
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* Restore SPI support on U-Boot 2019.04
* mvebu: kernel: Added Wake-On-GPIO and WoL support
The patch set was missing during transition.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* [#1429] SolidRun's ARMADA A388 SOM U-Boot ODT Update
Old versions of U-Boot did not configure correctly the ODT on data
signals of DDR RAM on SolidRun's ARMADA A388 SOMs.
According to SolidRun Knowledge Base, the changes already pushed to
mainline U-Boot. But then it was overwritten when Marvell DDR Training
Tool updated
[URL]
https://developer.solid-run.com/knowledge-base/armada-38x-som-u-boot-odt-update/
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* [#1429] mvebu: u-boot: Add revision id for Armada 38x B0
Added patch for SolidRun U-Boot v2018.01 and
for Helios4 U-Boot v2018.11
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* clearfog: Added SPI NOR flash target
Build bootable SPI NOR flash image.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* mvebu: clearfog: DEV branch use mainline U-Boot
Also move clearfog base patch into its own board folder.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* mvebu: enable U-Boot uart target
Normal MMC image can be used for uart boot using following command:
./tools/kwboot -b u-boot-spl.kwb /dev/ttyUSBX
But on Helios4, the SPL failed to continue the booting process if ECC is
enabled, so disable it.
Since the usage of uart boot is more for rescue/debug, disable autoboot.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* mvebu: NEXT branch use mainline U-Boot
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* mvebu: helios4: fix fancontrol related bug during buster testing
- On kernel 4.19, cpu thermal sensor changed the name from
armada_thermal into f10e4078.thermal. Added this new name to udev rules
- Since DEFAULT branch now use kernel 4.14, update fancontrol
configuration
- Load lm75 kernel module
- On kernel 4.19, cpu temp reading about 20 degree C lower, update
fancontrol configuration.
[URL]
https://forum.armbian.com/topic/10214-clearfogpro-possible-change-in-temperature-reporting-between-414next-and-419dev
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* mvebu: helios4: Override vendor provided fancontrol unit
systemd emit following message on dmesg
systemd[1]: /lib/systemd/system/fancontrol.service:9: PIDFile=
references path below legacy directory /var/run/, updating
/var/run/fancontrol.pid \xe2\x86\x92 /run/fancontrol.pid; please update
the unit file accordingly.
Override and change the value in the unit file to remove the message.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* mvebu: DEV branch use its own u-boot patch folder
The patches are copied over from u-boot-mvebu-next
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* mvebu: u-boot: Make clearfog model distinction more obvious
While at it, also change SerDes LANE4 into USB 3.0 on Clearfog Base.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* lib: Use apt-get install instead of dpkg on install_deb_chroot()
dpkg -i does not install dependencies required by the package.
This is needed if the BSP package requires other package that is not
installed during debootstrap.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* config: mvebu: helios4: Move various tweak to family_tweak_bsp()
Various tweak in family_tweaks_s() only applied to SD card image.
Move it to family_tweaks_bsp() so it will also included on the BSP
package and applied to existing user.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* config: mvebu: helios4: Add /etc/modules to BSP
On kernel 4.19, user need to modify the /etc/modules to add lm75 kernel
module. Pack the file into BSP so user no longer needed to modify it.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* mvebu: kernel: Make zbud as built-in module
To remove the following error:
[ 1.705485] zswap: default zpool zbud not available
[ 1.705488] zswap: pool creation failed
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* bootscripts: mvebu: Add default value for spi_workaround
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* mvebu: kernel: Backport armada_thermal changes to 4.14 (#1452)
On kernel 4.19, armada_thermal driver has been fixed to address
Marvell's Errata #132698 (The changes first appear on LK 4.16). The
result is temperature reading is around 20 degree Celsius lower.
Currently armbian-motd apply -20C tweak for both LK 4.14 and LK 4.19
which is incorrect. Instead of adding some logic on what condition to
apply the tweak, it is better to remove the tweak and patch the kernel
instead.
Revert commit b3dd4e9 ("[ mvebu ] Put back Armada temperature tweak in
motd")
which is part of #1421 solution.
[URL]
https://forum.armbian.com/topic/10214-clearfogpro-possible-change-in-temperature-reporting-between-414next-and-419dev/
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* mvebu: helios4: unified fancontrol config
Since LK 4.14 on DEFAULT branch already patched and the temp reading is
same as LK 4.19 on NEXT branch, it is no longer needed to separate
fancontrol configuration file.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* u-boot: helios4: Remove rev id patch
The patch is already applied in helios4 repo, no need to have it in
armbian.
This revert helios4 part of commit 7411c55
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* u-boot: clearfog: enable PCIe support and PCIe reset
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* u-boot: clearfog: add boot-marvell.cmd backward compatibility
The patches added missing variable that used on boot-marvell.cmd and
also adjust the some memory addresses to prevent crash due to usage of
fdt_high and initrd_high.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* mvebu: helios4: tweak regarding temperature setting
Make fan speed similar compared to pre-patched armada-thermal. Target
PWM value around 70 during idle.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* config: sources: clearfog to use u-boot 2018.01 for NEXT branch
This changes also affect Helios4. Moved the shared U-Boot source setting
back to Helios4 for NEXT branch.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* config: boards: build Stretch image for Clearfog and Helios4
Also remove DEV from Helios4 CLI_TARGET
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* kernel: mvebu-next: Disable access to SPI Flash
User need to set spi_workaround=yes to enable SPI Flash access and lost
access to internal SATA.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* mvebu-next: adjust kernel config
* mvebu-dev: bump to 5.2 and adjust kernel configuraion. Tested for building.
* Adjust kernel config, add AUFS
Signed-off-by: Igor Pecovnik <igor.pecovnik@gmail.com>
* mvebu-next: Adjust kernel config, add debug GPIO
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* mvebu-dev: separate Clearfog Base U-boot configuration file and patch
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
The eMMC must have been forgotten when the device tree for the NanoPi Neo Air was being added to mainline u-boot, which results in the device being unable to boot when installed to the internal eMMC using the nand-sata-install utility.
