Polished and fixed xt-q8lv-10 rockchip-legacy dtb
Reworked act8846 reboot patch for rockchip-legacy (applies, but not yet working though)
Renamed kernel updated patches in rockchip-legacy directory adding "04-" prefix to make them uniform with existing
* Moving Rockchip 32bit to 5.8.y
xt-q8l-v10 seems to be broken. I did a quick scan but couldn't resolve it. @paolosabatino
* Add wifi patches for 5.8.y
* [rockchip] Fixed xt-q8l-v10 DTS, reworked ath9k driver patch for 5.8.y (#2184)
* Fixed xt-q8l-v10 device tree to work on kernel 5.8.y on rockchip-current and -dev
* Reworked ath9k driver patch to compile on kernel 5.8.y for rockchip-current and -dev
* Add also wifi patches to DEV kernel
Co-authored-by: Paolo <paolo.sabatino@gmail.com>
Those were removed from mainline kernels by Chromebook devs,
wanting to protect their broken babies at all cost.
This patch was dully tested here :
https://forum.armbian.com/topic/13515-panfrost-on-rk3288-and-gpu-on-600mhz-problems/
But you're welcome to test it again !
I did it, with a whole glmark2 round and it worked flawlessly.
To test the GPU at that frequency, locate the **devfreq** folder of your GPU unit on your system (For tinkerboards, it's in **/sys/devices/platform/ffa30000.gpu/devfreq/ffa30000.gpu**) and then :
* Check the available frequencies by doing `sudo cat available_frequencies` .
That should output something like this : `100000000 200000000 300000000 400000000 500000000 600000000`
Be sure that `500000000` is in the list.
* Setup the minimum GPU frequency to 500Mhz like this : `sudo echo 500000000 > min_freq`
You can also set up the GPU to not go over 500Mhz like this : `sudo echo 500000000 > max_freq`
Signed-off-by: Miouyouyou (Myy) <myy@miouyouyou.fr>
* Move current to 5.7.x
* Update linux-rockchip-current.config
* Move dev patches to current
* copy dev to current
* move dev patches to current
* move rockchip64-current to 5.7.x
* For xt-q8l-v10 rk3288 board:
- Upgraded u-boot to v2020.04, reworked configuration to match new version, enabled HDMI video console
- Increased u-boot boot delay from 0 seconds to 1 second for rockchip boards, to allow user interrupt u-boot boot process
- Imported efuse rk3288 driver into u-boot, made ethernet address stable using soc serial
- Upgraded ddrbin loader to v1.08
- Added VDSO patch for rockchip-current and rockchip-dev kernels for clock_gettime64 to fix erratic clock on 32 bit ARM devices with recent glibc
- Disabled 600 Mhz OPP node for GPU due to Panfrost instabilities, thus enabled 500 Mhz node
- Various fixes and enhancements to xt-q8l-v10 device trees for current and dev targets
- Added (disabled) u-boot HDMI patch for Tinkerboard
* Removed rk3288 ddrbin v1.08 from rockchip blobs, changed reference to use rkbin-tools repository
* Removed unneeded disabled patch for tinkerboard HDMI
* Added ALSA configuration bits for rk3288 HDMI and SPDIF to allow
pulseaudio show proper sound device/profile/mapping names instead of
just "Built-in Audio" for all of them
* Added ALSA device description in asound.conf to provide correct labels for PulseAudio for RK3288 devices when SPDIF and DW-I2S-HDMI simple audio cards are exposed
Removed unnecessary ALSA configuration files previously added from rockchip.conf
* Fixed cpu operating points tables and raised a bit (+5°C) cooling for non-critical temperatures for xt-q8l-v10 in dev and next kernel flavours
* Fixed again cpu opp table
* Removed whole cpu opp table and retouch only necessary operating points
* Enabled gpiomem driver for xt-q8l-v10 in next kernel flavour
* Added debounce delay and card detect gpio pins for sdmmc card holder for xt-q8l-v10 board
* Added card-detect and debounce delay for sdmmc for xt-q8l-v10 board in next kernel flavour too
* Fixed missing comment in xt-q8l-v10 device tree patch
* Added gpiomem to xt-q8l-v10 board for dev kernel
* Fixed FAN53555/Silergy patches to accomodate changes in u-boot v2019.04
* Changed property property flags for USB regulators in u-boot and kernel: kernel is now informed that bootloader is going to turn the USB power on
* Fixed indentation in rk3288-xt-q8l-v10.dts, raised debounce delay to sdmmc, added vbus-supply to USB host, removed some unneeded properties
* Added working DDR52 mode for eMMC on xt-q8l-v10
* Removed regulator-off-in-suspend for some xt-q8l-v10 regulators due to changed in act8865.c driver which causes the regulators to be misconfigured
* Adjusted targets for xt-q8l-v10 (provides bionic desktop + buster server)
* Removed all regular-state-mem nodes in xt-q8l-v10 device tree because the change in act8865.c affects also non-off entries
* Brought xt-q8l-v10 device tree from rockchip-current to rockchip-dev
* Wireguard: bump tag to most recent since it breaks building on 5.4.y
* Move rockchip current to 5.4.y
* Move sunxi current to 5.4.y
* Move meson64 to 5.4.y
* Move odroidxu4 to 5.4.y and enable "current" targets
* Enable missing target
AR-1 - Adding support category for distributions
AR-4 - Remove Allwinner legacy
AR-5 - Drop Udoo family and move Udoo board into newly created imx6 family
AR-9 - Rename sunxi-next to sunxi-legacy
AR-10 - Rename sunxi-dev to sunxi-current
AR-11 - Adding Radxa Rockpi S support
AR-13 - Rename rockchip64-default to rockchip64-legacy
AR-14 - Add rockchip64-current as mainline source
AR-15 - Drop Rockchip 4.19.y NEXT, current become 5.3.y
AR-16 - Rename RK3399 default to legacy
AR-17 - Rename Odroid XU4 next and default to legacy 4.14.y, add DEV 5.4.y
AR-18 - Add Odroid N2 current mainline
AR-19 - Move Odroid C1 to meson family
AR-20 - Rename mvebu64-default to mvebu64-legacy
AR-21 - Rename mvebu-default to mvebu-legacy
AR-22 - Rename mvebu-next to mvebu-current
AR-23 - Drop meson64 default and next, current becomes former DEV 5.3.y
AR-24 - Drop cubox family and move Cubox/Hummingboard boards under imx6
AR-26 - Adjust motd
AR-27 - Enabling distribution release status
AR-28 - Added new GCC compilers
AR-29 - Implementing Ubuntu Eoan
AR-30 - Add desktop packages per board or family
AR-31 - Remove (Ubuntu/Debian) distribution name from image filename
AR-32 - Move arch configs from configuration.sh to separate arm64 and armhf config files
AR-33 - Revision numbers for beta builds changed to day_in_the_year
AR-34 - Patches support linked patches
AR-35 - Break meson64 family into gxbb and gxl
AR-36 - Add Nanopineo2 Black
AR-38 - Upgrade option from old branches to new one via armbian-config
AR-41 - Show full timezone info
AR-43 - Merge Odroid N2 to meson64
AR-44 - Enable FORCE_BOOTSCRIPT_UPDATE for all builds
